DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

PET-HT DIELECTRIC – CB Series GENERAL DESCRIPTION Film chip capacitor using a naked and stacked construction with metallized High Temperature PET (polyethylene terephtalate). ADVANTAGES

  • Use of high temperature dielectric films makes these capacitors suitable for IR or vapor phase reflow processes. This chip is built without specific encapsulation.
  • The intrinsic elasticity of the dielectric film allows an excellent compatibility of the capacitor with all types of material for printed circuit boards.
  • The self-healing property of film technology results to a safety open failure mode and better overall reliability.
  • Excellent thermal shock resistance.
  • Low dissipation factor ESR & ESL.
  • No piezoelectric effect.
  • Available in tape and reel suitable for automatic placement.
  • Non-polar construction. Outer Layer Termination Plating : 100% matte Sn Ni Barrier Under Termination Silver Epoxy Resin Brass Active Layers : PET dielectric

APPLICATIONS

General purpose function in low voltage applications where miniaturization and SMD is required. Typical applications would be:

  • Automotive (Airbag, Fuel injection calculator...)
  • Telecom (Public switching systems, modems, telephone set, cordless, mobile)
  • Industrial (SMPS, Power convertor module...) PERFORMANCE CHARACTERISTICS Climatic Category 55/125/56 Capacitance Range 10nF to 4.7μF Tolerance on CR ±5%, ±10% Nominal Voltages 63Vdc to 630Vdc Test Voltage 1.4Vr 2 sec. at 25°C Soldering methods IR or vapor phase reflow (not suitable for wave soldering) Tangent of Loss Angle at 1kHz (DF) < 100 x 10-4 Insulation resistance minimum : IR for C ≤ 0.33μF IR > 1000 MΩ at 20°C for 1 min. charge at 10Vdc for VR < 100Vdc and 100Vdc for VR ≥ 100Vdc for C > 0.33μF IR C > 400 sec. at 20°C for 1 min. charge at 10Vdc for VR < 100Vdc and 100Vdc for VR ≥ 100Vdc Temperature range -55°C to 125°C with voltage derating of 1.25%/°C between 105°C and 125°C A.C. applications for high frequency A.C. application please check with AVX

PET-HT DIELECTRIC – CB Series CAPACITANCE VALUES (CR) AND NOMINAL VOLTAGES (VR) VOLTAGE Vdc: 63V Vac: 40V Capacitance Chip Dimensions Reel Range Ordering *Tolerances Tape Dimensions Reel Dimensions Packaging Unit Pkg (CR) Code (page 6) Code L W H max T W P1 K0 A W1 W2 max Bulk Reel VOLTAGE Vdc: 100V Vac: 63V Replace the + by the tolerance code: J = 5% or K = 10% Replace the -- by the packaging suffix: -- = bulk BC = tape & reel millimeters (inches) W L H T

PET-HT DIELECTRIC – CB Series CAPACITANCE VALUES (CR) AND NOMINAL VOLTAGES (VR) VOLTAGE Vdc: 100V Vac: 63V Capacitance Chip Dimensions Reel Range Ordering *Tolerances Tape Dimensions Reel Dimensions Packaging Unit Pkg (CR) Code (page 6) Code L W H max T W P1 K0 A W1 W2 max Bulk Reel VOLTAGE Vdc: 250V Vac: 160V Replace the + by the tolerance code: J = 5% or K = 10% Replace the -- by the packaging suffix: -- = bulk BC = tape & reel millimeters (inches) W L H T

PET-HT DIELECTRIC – CB Series CAPACITANCE VALUES (CR) AND NOMINAL VOLTAGES (VR) VOLTAGE Vdc: 400V Vac: 200V Capacitance Chip Dimensions Reel Range Ordering *Tolerances Tape Dimensions Reel Dimensions Packaging Unit Pkg (CR) Code (page 6) Code L W H max T W P1 K0 A W1 W2 max Bulk Reel VOLTAGE Vdc: 630V Vac: 250V Replace the + by the tolerance code: J = 5% or K = 10% Replace the -- by the packaging suffix: -- = bulk BC = tape & reel millimeters (inches) W L H T

PET-HT DIELECTRIC – CB Series CAPACITANCE VALUES (CR) AND NOMINAL VOLTAGES (VR) VOLTAGE Vdc: 630V Vac: 250V Capacitance Chip Dimensions Reel Range Ordering *Tolerances Tape Dimensions Reel Dimensions Packaging Unit Pkg (CR) Code (page 6) Code L W H max T W P1 K0 A W1 W2 max Bulk Reel Replace the + by the tolerance code: J = 5% or K = 10% Replace the -- by the packaging suffix: -- = bulk BC = tape & reel millimeters (inches) W L H T

PET-HT DIELECTRIC – CB Series MOUNTING AND SOLDERING RECOMMENDATIONS *Reflow soldering referring to JEDEC Standard with some limitations *JEDEC J-Std 020C SOLDERING PROFILE The capacitors can be mounted using infrared and vapor phase soldering following recommended below. They are NOT suitable for wave soldering. All temperature refer to topside of the package, measured on the package body surface. RECOMMENDED SOLDER PASTE THICKNESS Profile Feature 2220 to 2824 4030 to 6054 Ramp-Up (Ts max to Tp) 3°C / second max 3°C / second max Preheat - Temperature Min (Ts min) 150°C 150°C - Temperature Min (Ts max) 200°C 200°C - Time (ts min to ts max) 180 sec. max 180 sec. max Time maintained above - Temperature (T L) 217°C 217°C - Time (tL) 60 sec. max 75 sec. max Peak temperature (Tp) 240°C 245°C Time within 5°C of peak 10 sec. 10 sec.temperature (tp) Ramp-Down 6°C / sec. 6°C / sec. For optimum solderability, the recommended soldering paste thickness: 2220 to 2824 :150 to 200µm 4030 to 6054 :200 to 300µm In case of hand soldering, the temperature of the soldering iron should not be above 250°C. Special care must be taken to avoid touching the capacitor body with the iron tip. Size Code Case Size A B C PAD DIMENSIONS:millimeters (inches) A CB RECOMMENDED CLEANING To clean flux from the PC board assembly, the recommended products are: ethanol, isopropyl alcohol, and deionized water wash. The cleaning products to avoid are: Toluene, Xylene, Trichloroethylene, Terpene Cleaner EC-7, surface active agent. In case of using another solvent, please contact us. OTHER CAUTIONS Flame retardancy: the dielectric film is not a flame retardant material. Environment: contact us when chips are used in humid or gas atmosphere and /or when using resin. Recommended handling: do not use edged tools, so not to damage the capacitors. TIN WHISKERS TESTS : JEDEC STANDARD NO 22A121 Stress Type Ref. Spec. Test Conditions Analysis Results Temperature cycling JESD22-A104 -55°C +85(+10/-0)°C air SEM x 1000 Pass 5 to 10 minutes soak 3 cycles/hour Ambient Temperature / 30+/-2°C - 60+/-3% RH -2000H SEM x 1000 Pass Humidity Storage High Temperature / 70+/-5°C - 93+3/-2% RH -1000H SEM x 1000 Pass Humidity Storage 03 0 Time (seconds) Temperature (ºC) 60 90 120 150 180 210 240 Ramp down Ramp up 270 300 330 Tp Tp - 5ºC Ts min Ts max TL tS tp tL

PET-HT DIELECTRIC – CB Series ELECTRICAL CHARACTERISTICS VERSUS TEMPERATURE AND FREQUENCY

ELECTRICAL CHARACTERISTICS

/H9004C/C vs TEMPERATURE Temperature 10000.0 1000.0 100.0 10.0 1.0 0.1 IR(G.ohm) Temperature IR vs TEMPERATURE 100nF 160 140 120 100 DC/C = (temperature) Temperature DF (1kHz) vs TEMPERATURE D.F . (10-4) Capacitance Dissipation Factor Insulation Resistance FREQUENCY CHARACTERISTICS 0.1 1 10 100 1000 /H9004C/C 20°C (%) FREQUENCY (kHz) 1000.00 100.00 10.00 1.00 1.00 10.00 FREQUENCY (MHz) Z (mOhm) 1µF 470 nF 220 nF 47 nF 100 nF 4.7µF 400 300 200 100 0 10 100 100010.1 DF 20°C (10 )-4 FREQUENCY (kHz) Capacitance Dissipation Factor Impedance

PET-HT DIELECTRIC – CB Series RMS VOLTAGE AND CURRENT VERSUS FREQUENCY MAXIMUM VOLTAGE (VRMS) AND CURRENT (IRMS) VS FREQUENCY Typical curves results from measurement carried out at ambient temperature (25ºC) and sinusoidal wave-forms (for size CB04 to CB18) 0.1 1 10 100 1000 10000 FREQUENCY (kHz) V rms (V) 4.7µF 1.5µF 0.47µF 100 120 140 160 180 0.1 1 10 100 1000 10000 FREQUENCY (kHz) V rms (V) 1µF 0.47µF 0.1µF 0.1 1 10 100 1000 10000 FREQUENCY (kHz) V rms (V) 4.7µF 1.5µF 0.22µF 63Vdc / 40 Vac

100 Vdc / 63 Vac

250 Vdc / 160 Vac

0.5 1.5 2.5 3.5 4.5 0.1 1 10 100 1000 10000 I rms (A) 4.7µF 1.5µF 0.47µF FREQUENCY (kHz) 0.5 1.5 2.5 3.5 4.5 5.5 0.1 1 10 100 1000 10000 FREQUENCY (kHz) I rms (A) 1µF 0.47µF 0.1µF 0.5 1.5 2.5 3.5 4.5 5.5 6.5 0.1 1 10 100 1000 10000 FREQUENCY (kHz) I rms (A) 4.7µF 1.5µF 0.22µF 63Vdc / 40 Vac

PET-HT DIELECTRIC – CB Series RMS VOLTAGE AND CURRENT VERSUS FREQUENCY MAXIMUM PULSE RISE TIME (DV/DT) MAXIMUM VOLTAGE (VRMS) AND CURRENT (IRMS) VS FREQUENCY Typical curves results from measurement carried out at ambient temperature (25ºC) and sinusoidal wave-forms (for size CB04 to CB18) 100 120 140 160 180 200 220 0.1 1 10 100 1000 10000 FREQUENCY (kHz) V rms (V) 0.47µF 0.1µF 0.01µF 0.5 0.1 1 10 100 1000 10000 FREQUENCY (kHz) I rms (A) 0.47µF 0.1µF 0.01µF

400 Vdc / 200 Vac 400 Vdc / 200 Vac

0.1 1 10 100 1000 10000 FREQUENCY (kHz) V rms (V) 0.27µF 0.1µF 0.01µF 0.5 0.1 1 10 100 1000 10000 FREQUENCY (kHz) I rms (A) 0.27µF 0.1µF 0.01µF

630 Vdc / 250 Vac 630 Vdc / 250 Vac

Voltage Range 63 100 250 400 630 Dv/dt max. 40 50 150 200 250(V/µsec)

PET-HT DIELECTRIC – CB Series – RoHS MATERIALS CONTROLLED BY ROHS (PPM BY WEIGHT): Mass / unit (g) Lead Mercury Cadmium Hexavalent PBB PBDEChromium CB range 000 0 00 RoHS Limit (ppm) 1000 1000 100 1000 1000 1000 Pass/Fail Pass Pass Pass Pass Pass Pass This product has been tested and found to be compliant with all requirements, provisions, and exemptions of EU Directive 2002/9 5/EC of the European Parliament and Council of January 27, 2003. On the Restriction of use of certain Hazardous Substances (RoHS) in electrical and electronic equi pment and EU Directive 2000/53/EC regarding ELV or End of Life Vehicle. ROHS / ELV STATUS External Plating 100% Matte Sn as standard LEAD-FREE STATUS / MOISTURE SENSITIVITY RANKING Pb Free Reflow Solder compliant, MSL = 3. Reflow soldering referring to Jedec Standard with some limitations. Additional JESD-97 data to be phased in MSL e3 termination. PRODUCT LABELING: (For informational purposes only to be phased in on reel and container.) PRODUCT TRACEABILITY: Full internal material traceability by reference to unique lot number marked on reel and external package. RoHS Compliant:Pb Free: