CA3078 INTERSIL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 12

Technical content

Features

  • Adjustable Quiescent Current
  • Output Short Circuit Protection

Applications

  • Portable Electronics • Intrusion Alarms
  • Telemetry • Instrumentation
  • Medical Electronics Pinouts CA3078 (PDIP, SOIC) TOP VIEW CA3078 (METAL CAN) TOP VIEW NOTE: Case Voltage = Floating Schematic Diagram

Ordering Information

(BRAND) TEMP. RANGE ( oC) PACKAGE PKG. NO. CA3078AE -55 to 125 8 Ld PDIP E8.3 CA3078AM (3078A) -55 to 125 8 Ld SOIC M8.15 CA3078AM96 (3078A) -55 to 125 8 Ld SOIC Tape and ReelM8.15 CA3078AT -55 to 125 8 Pin Metal Can T8.C CA3078E 0 to 70 8 Ld PDIP E8.3 CA3078M (3078) 0 to 70 8 Ld SOIC M8.15 CA3078T 0 to 70 8 Pin Metal Can T8.C COMP INV. INPUT NON-INV. INPUT COMP OUTPUT BIAS COMP OUTPUT BIAS TAB R SETV+ NON-INV. INPUT INV. INPUT

3 Q 1 Q 3

50Ω Q 18 OUTPUTQ 16 Q 11 Q 13 Q 15 Q 17 D 8 Q 9 Q 14 50Ω COMPENSATION D 6 D 7 Q 5 D 4 Q 2 D 1 BIAS INVERTING D 2 D 3 D 5 NON- INVERTING Q 7 Q 8 Data Sheet December 1998 File Number 535.5 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143| Copyright © Intersil Corporation 1999

Absolute Maximum Ratings Thermal Information Supply Voltage (Between V+ and V- Terminal) Operating Conditions Temperature Range Thermal Resistance (Typical, Note 2)θJA (oC/W) θJC (oC/W) oC (SOIC - Lead Tips Only) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Short circuit may be applied to ground or to either supply. 2. θ JA is measured with the component mounted on an evaluation PC board in free air. Electrical SpecificationsFor Equipment Design PARAMETER TEST CONDITIONS CA3078 LIMITS CA3078A LIMITS UNITS R SET = 1MΩ R SET = 5.1MΩ and V- R S (kΩ ) R L (kΩ ) TA = 25oC TA = 0oC to 70oCT A = 25oC TA = -55oC to 125oC MIN TYP MAX MIN MAX MIN TYP MAX MIN MAX IIO - - - 6 32 - 40 - 0.50 2.5 - 5.0 nA IIB - - - 60 170 - 200 - 7 12 - 50 nA AOL - ≥10 88 92 - 86 - 92 100 - 90 - dB IQ - - - 100 130 - 150 - 20 25 - 45 µA PD - - - 1200 1560 - 1800 - 240 300 - 540 µW VICR ≤10 - - -5.5 to +5.8 - -5 to - - -5.5 to +5.8 - -5 to CMRR ≤10 - 80 110 - - - 80 115 - - - dB IOM + or IOM - - - - 12 - 6.5 30 - 12 - 6.5 30 mA R SET = 13MΩ AOL - ≥10 - - - - - 92 100 - 88 - dB PD - - - - - - - - 600 750 - 1350 µW CA3078, CA3078A

Electrical SpecificationsTA = 25oC, Typical Values Intended Only for Design Guidance PARAMETER CA3078 CA3078A UNITS V+ = +1.3V, V- = -1.3V R SET = 2MΩ V+ = +0.75V, V- = -0.75V R SET = 10MΩ V+ = +1.3V, V- = -1.3V R SET = 2MΩ V+ = +0.75V, V- = -0.75V R SET = 10MΩ VIO 1.3 1.5 0.7 0.9 mV IIO 1.7 0.5 0.3 0.054 nA IIB 9 1.3 3.7 0.45 nA AOL 80 60 84 65 dB IQ 10 1 10 1 µA PD 26 1.5 26 1.5 µW VOP-P 1.4 0.3 1.4 0.3 V CMRR 100 90 100 90 dB IOM ± 12 0.5 12 0.5 mA ∆VIO/∆V± 20 50 20 50 µV/V Electrical SpecificationsTA = 25oC and VSUPPLY =±6V, Typical Values Intended Only for Design Guidance PARAMETER TEST CONDITIONS CA3078 CA3078A UNITSR SET = 1MΩ R SET = 5.1MΩ R SET = 1MΩ ∆VIO/∆TA R S ≤10kΩ 656 µV/oC ∆IIO/∆TA R S ≤10kΩ 70 6.3 70 pA/ oC GBWP A V = 100, C1 = 10pF 2 0.3 2 MHz SR See Figures 23, 24 0.04 0.027 0.04 V/ µs 1.5 0.5 1.5 V/ µs tR 10% to 90% Rise Time 2.5 3 2.5 µs R I - 0.87 7.4 1.7 M Ω R O - 0.8 1 0.8 k Ω eN (10Hz) R S = 0 25 40 - nV/ √Hz iN (10Hz) R S = 1MΩ 1 0.25 - pA/ √Hz CA3078, CA3078A

Dual-In-Line Plastic Packages (PDIP) CL E eA C eB eC -B- INDEX 1 2 3 N/2 N AREA SEATING BASE PLANE PLANE -C- B e D AA2 L -A- 0.010 (0.25) C AM B S NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication No. 95. 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. 5. D, D1, and E1 dimensions do not include mold flash or protru- sions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and are measured with the leads constrained to be per- pendicular to datum . 7. e B and eC are measured at the lead tips with the leads uncon- strained. eC must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). eA -C- E8.3(JEDEC MS-001-BA ISSUE D)

8 LEAD DUAL-IN-LINE PLASTIC PACKAGE

A - 0.210 - 5.33 4 A1 0.015 - 0.39 - 4 A2 0.115 0.195 2.93 4.95 - B 0.014 0.022 0.356 0.558 - B1 0.045 0.070 1.15 1.77 8, 10 C 0.008 0.014 0.204 0.355 - D 0.355 0.400 9.01 10.16 5 D1 0.005 - 0.13 - 5 E 0.300 0.325 7.62 8.25 6 E1 0.240 0.280 6.10 7.11 5 e 0.100 BSC 2.54 BSC - e A 0.300 BSC 7.62 BSC 6 eB - 0.430 - 10.92 7 L 0.115 0.150 2.93 3.81 4 N8 8 9 Rev. 0 12/93 CA3078, CA3078A

Small Outline Plastic Packages (SOIC) INDEX AREA E D N 123 -B- 0.25(0.010) C AM B S e -A- L B M -C- A SEATING PLANE 0.10(0.004) h x 45o C H 0.25(0.010) BM M α NOTES: 11. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 12. Dimensioning and tolerancing per ANSI Y14.5M-1982. 13. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 14. Dimension “E” does not include interlead flash or protrusions. Inter- lead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 15. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 16. “L” is the length of terminal for soldering to a substrate. 17. “N” is the number of terminal positions. 18. Terminal numbers are shown for reference only. 19. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 20. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. M8.15 (JEDEC MS-012-AA ISSUE C)

8 LEAD NARROW BODY SMALL OUTLINE PLASTIC

A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.1890 0.1968 4.80 5.00 3 E 0.1497 0.1574 3.80 4.00 4 e 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N8 8 7 α 0o 8o 0o 8o - Rev. 0 12/93 CA3078, CA3078A

All Intersil semiconductor products are manufactured, assembled and tested underISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time with- out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web sitewww.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee

1130 Brussels, Belgium

TEL: (32) 2.724.2111 ASIA Intersil (Taiwan) Ltd. 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029 Metal Can Packages (Can) NOTES: 1. (All leads) Øb applies between L1 and L2. Øb1 applies between L2 and 0.500 from the reference plane. Diameter is uncontrolled in L1 and beyond 0.500 from the reference plane. 2. Measured from maximum diameter of the product. α is the basic spacing from the centerline of the tab to terminal 1 and β is the basic spacing of each lead or lead position (N -1 places) fromα ,looking at the bottom of the package. 4. N is the maximum number of terminal positions. 5. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 6. Controlling dimension: INCH. Øb ØD2 Ø e k1 k βØb1 BASE AND SEATING PLANE F Q ØD ØD1 REFERENCE PLANE L A α Øb2Øb1 BASE METAL LEAD FINISH SECTION A-A A A N CL T8.C MIL-STD-1835 MACY1-X8 (A1)

8 LEAD METAL CAN PACKAGE

A 0.165 0.185 4.19 4.70 - Øb 0.016 0.019 0.41 0.48 1 Øb1 0.016 0.021 0.41 0.53 1 Øb2 0.016 0.024 0.41 0.61 - ØD 0.335 0.375 8.51 9.40 - ØD1 0.305 0.335 7.75 8.51 - ØD2 0.110 0.160 2.79 4.06 - e 0.200 BSC 5.08 BSC - e1 0.100 BSC 2.54 BSC - F - 0.040 - 1.02 - k 0.027 0.034 0.69 0.86 - k1 0.027 0.045 0.69 1.14 2 L 0.500 0.750 12.70 19.05 1 L1 - 0.050 - 1.27 1 L2 0.250 - 6.35 - 1 Q 0.010 0.045 0.25 1.14 - α 45o BSC 45 o BSC 3 β 45o BSC 45 o BSC 3 N8 8 4 Rev. 0 5/18/94 CA3078, CA3078A