CA3059 MOTOROLA | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
/C0067/C0065/C0051/C0048/C0053/C0057 SEMICONDUCTOR TECHNICAL DATA ZERO VOLTAGE SWITCH
ORDERING INFORMATION
CA3059 T A = – 40° to +85°C Plastic DIP PLASTIC PACKAGE CASE 646 Order this document by CA3059/D FUNCTIONAL BLOCK
DESCRIPTION
- Limiter–Power Supply — Allows operation of the CA3059 directly from an AC line. Suggested dropping resistor (RS) values are given in the table below.
Figure 1. Representative Block Diagram
400 Hz Input
- Differential On/Off Sensing Amplifier — Tests
may be implemented using this block.
- Zero–Crossing Detector — Synchronizes the
output pulses to the zero voltage point of the AC cycle.
- Triac Drive — Supplies high–current pulses to
the external power controlling thyristor.
- Protection Circuit — A built–in circuit may be
drive current from the external triac.
- Inhibit Capability — Thyristor firing may be
- High Power DC Comparator Operation —
respect to Pin 9, current to the thyristor is continuous.
- Relay Control • Heater Control
- Valve Control • Lamp Control
- On–Off Motor Switching
- Differential Comparator with Self–Contained Power Supply for Industrial
Applications
- Synchronous Switching of Flashing Lights AC Input Voltage (50/60 Hz) Vac Input Series Resistor (RS) kΩ Dissipation Rating for RS W 24 2.0 0.5 120 10 2.0 208/230 20 4.0 277 25 5.0 Motorola, Inc. 1996 Rev 0
2 MOTOROLA ANALOG IC DEVICE DATA
(Between Pins 2 and 7) 12 DC Supply Voltage VCC Vdc (Between Pins 2 and 8) 12 Peak Supply Current (Pins 5 and 7) I5,7 ± 50 mA Fail–Safe Input Current (Pin 14) I14 2.0 mA Output Pulse Current (Pin 4) (Note 1) Iout 150 mA Junction Temperature TJ 150 °C Operating Temperature Range TA – 40 to + 85 °C Storage Temperature Range Tstg – 65 to + 150 °C ELECTRICAL CHARACTERISTICS (Operation @ 120 Vrms, 50–60 Hz, TA = 25°C [Note 2]) Characteristic Figure Symbol Min Typ Max Unit DC Supply Voltage 2 VS Vdc Inhibit Mode R S = 10 k, IL = 0 6.1 6.5 7.0 R S = 5.0 k, IL = 2.0 mA — 6.1 — Pulse Mode R S = 10 k, IL = 0 6.0 6.4 7.0 R S = 5.0 k, RL = 2.0 mA — 6.2 — Gate Trigger Current 3 IGT — 160 — mA (VGT = 1.0 V, Pins 3 and 2 connected) Peak Output Current, Pulsed 3 IOM mA With Internal Power Supply, VGT = 0 Pin 3 Open 50 125 — Pins 3 and 2 Connected 90 190 — With External Power Supply, VCC = 12 V, VGT = 0 4 Pin 3 Open — 230 — Pins 3 and 2 Connected — 300 — Inhibit Input Ratio 5 V9/V2 0.465 0.485 0.520 — (Ratio of Voltage @ Pin 9 to Pin 2) Total Gate Pulse Duration (CExt = 0) 6 µs Positive dv/dt tp 70 100 140 Negative dv/dt tn 70 100 140 Pulse Duration After Zero Crossing 6 µs (CExt = 0, RExt = /C0082) Positive dv/dt tp1 — 50 — Negative dv/dt tn1 — 60 — Output Leakage Current Inhibit Mode (Note 3) 3 I4 — 0.001 10 µA Input Bias Current 7 IIB — 0.15 1.0 µA Common Mode Input Voltage Range (Pins 9 and 13 Connected) — VCMR — 1.4 to 5.0 — Vdc (Pins 9 and 13 Connected) Inhibit Input Voltage 8 V1 — 1.4 1.6 Vdc External Trigger Voltage — V6–V4 — 1.4 — Vdc NOTES: 1. Care must be taken, especially when using an external power supply, that total package dissipation is not exceeded. 2. The values given in the Electrical Characteristics Table at 120 V also apply for operation at input voltages of 24 V, 208/230 V, and 277 V, except for Pulse Duration test. However, the series resistor (RS) must have the indicated value, shown in Table A for the specified input voltage. 3. I4 out of Pin 4, 2.0 V on Pin 1, S1 position 2.
Figure 2. DC Supply Voltage Figure 3. Peak Output (Pulsed) and Gate
120 Vrms
Figure 4. Peak Output Current (Pulsed) Figure 5. Input Inhibit Ratio Figure 6. Gate Pulse Duration Test Circuit Figure 7. Input Bias Current Test Circuit
4 MOTOROLA ANALOG IC DEVICE DATA
120 Vrms, 60 Hz
Figure 8. Inhibit Input Voltage Test Figure 9. Peak Output Current (Pulsed)
120 Vrms, 60Hz
120 Vrms, 60 Hz Operation
Figure 10. Peak Output Current (Pulsed) Figure 11. Total Pulse Width versus Figure 12. Internal Supply versus Figure 13. Inhibit Voltage Ratio versus
6 MOTOROLA ANALOG IC DEVICE DATA
CASE 646–06 ISSUE L OUTLINE DIMENSIONS NOTES: 1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 4. ROUNDED CORNERS OPTIONAL. 14 8 B A F HG D K C N L J M SEATING PLANE DIM MIN MAX MIN MAX MILLIMETERSINCHES A 0.715 0.770 18.16 19.56 B 0.240 0.260 6.10 6.60 C 0.145 0.185 3.69 4.69 D 0.015 0.021 0.38 0.53 F 0.040 0.070 1.02 1.78 G 0.100 BSC 2.54 BSC H 0.052 0.095 1.32 2.41 J 0.008 0.015 0.20 0.38 K 0.115 0.135 2.92 3.43 L 0.300 BSC 7.62 BSC M 0 10 0 10 N 0.015 0.039 0.39 1.01 /C0095/C0095/C0095/C0095 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;JAPAN : Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–54543–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 INTERNET : http://Design–NET.com 51 Ting Kok R oad, Tai Po, N.T., Hong Kong. 852–26629298 CA3059/D /C0042/C0067/C0065/C0051/C0048/C0053/C0057/C0047/C0068/C0042