C062C-K-G

C622C102MDR5TA KEMET | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 14

Technical content

© KEMET Electronics Corporation, P .O. Box 5928, Greenville, S.C. 29606, (864) 963-63004 MULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED Multilayer ceramic capacitors are available in a variety of physical sizes and configurations, including leaded devices and surface mounted chips. Leaded styles include molded and conformally coated parts with axial and radial leads. However, the basic capacitor element is similar for all styles. It is called a chip and consists of formulated dielectric materials which have been cast into thin layers, interspersed with metal electrodes alternately exposed on opposite edges of the laminated structure. The entire structure is fired at high temperature to produce a monolithic block which provides high capacitance values in a small physical volume. After firing, conductive terminations are applied to opposite ends of the chip to make contact with the exposed electrodes. Termination materials and methods vary depending on the intended use. TEMPERATURE CHARACTERISTICS Ceramic dielectric materials can be formulated with a wide range of characteristics. The EIA standard for ceramic dielectric capacitors (RS-198) divides ceramic dielectrics into the following classes: Class I: Temperature compensating capacitors, suitable for resonant circuit application or other appli- cations where high Q and stability of capacitance char- acteristics are required. Class I capacitors have predictable temperature coefficients and are not affected by voltage, frequency or time. They are made from materials which are not ferro-electric, yielding superior stability but low volumetric ef ficiency. Class I capacitors are the most stable type available, but have the lowest volumetric efficiency. Class II: Stable capacitors, suitable for bypass or coupling applications or frequency discriminating circuits where Q and stability of capacitance char- acteristics ar e not of major importance. Class II capacitors have temperature characteristics of ± 15% or less. They ar e made fr om materials which ar e ferro-electric, yielding higher volumetric efficiency but less stability. Class II capacitors are affected by temperature, voltage, frequency and time. Class III: General purpose capacitors, suitable for by-pass coupling or other applications in which dielectric losses, high insulation resistance and stability of capacitance characteristics are of little or no importance. Class III capacitors are similar to Class II capacitors except for temperature characteristics, which are greater than ± 15%. Class III capacitors have the highest vol umetric efficiency and poorest stability of any type. KEMET leaded ceramic capacitors are offered in the three most popular temperature characteristics: C0G: Class I, with a temperature coefficient of 0 ± 30 ppm per degree C over an operating temperature range of - 55°C to + 125°C (Also known as “NP0”). X7R: Class II, with a maximum capacitance change of ± 15% over an operating temperature range of - 55° C to + 125°C. Z5U: Class III, with a maximum capacitance change of + 22% - 56% over an operating tem- perature range of + 10° C to + 85° C. Specified electrical limits for these three temperature characteristics are shown in Table 1. SPECIFIED ELECTRICAL LIMITS Table I C0G X7R Z5U Dissipation Factor: Measured at following conditions. C0G – 1 kHz and 1 vrms if capacitance >1000pF

1 MHz and 1 vrms if capacitance 1000 pF

X7R – 1 kHz and 1 vrms* or if extended cap range 0.5 vrms Z5U – 1 kHz and 0.5 vrms 0.10% 2.5% (3.5% @ 25V) 4.0% Dielectric Stength: 2.5 times rated DC voltage. Insulation Resistance (IR): At rated DC voltage, whichever of the two is smaller 1,000 M F or 100 G 1,000 M F or 100 G 1,000 M F or 10 G Temperature Characteristics: Range, °C Capacitance Change without DC voltage -55 to +125 0 ± 30 ppm/° C -55 to +125 ± 15% + 10 to +85 +22%,-56% * MHz and 1 vrms if capacitance 100 pF on military product. Parameter Temperature Characteristics Pass Subsequent IR Test

APPLICATION NOTES FOR MULTILAYER CERAMIC CAPACITORS © KEMET Electronics Corporation, P .O. Box 5928, Greenville, S.C. 29606, (864) 963-63006 TABLE 1 EIA TEMPERATURE CHARACTERISTIC CODES FOR CLASS I DIELECTRICS Significant Figure Multiplier Applied Tolerance of of Temperature to Temperature Temperature Coefficient Coefficient Coefficient * PPM per Letter Multi- Number PPM per Letter Degree C Symbol plier Symbol Degree C Symbol

0.0 C -1 0 ±30 G

0.3 B -10 1 ±60 H

0.9 A -100 2 ±120 J

1.0 M -1000 3 ±250 K

1.5 P -100000 4 ±500 L

2.2 R +1 5 ±1000 M

3.3 S +10 6 ±2500 N

4.7 T +100 7

7.5 U +1000 8

+10000 9 * These symetrical tolerances apply to a two-point measur ement of temperature coefficient: one at 25°C and one at 85°C. Some deviation is permitted at lower temperatures. For example, the PPM tolerance for C0G at -55°C is +30 / -72 PPM. TABLE 2 EIA TEMPERATURE CHARACTERISTIC CODES FOR CLASS II & III DIELECTRICS Low Temperature High Temperature Maximum Capacitance Rating Rating Shift Degree Letter Degree Number Letter Celcius Symbol Celcius Symbol Percent Symbol +10C Z +45C 2 ±1.0% A -30C Y +65C 4 ±1.5% B -55C X +85C 5 ±2.2% C +105C 6 ±3.3% D +125C 7 ±4.7% E +150C 8 ±7.5% F +200C 9 ±10.0% P ±15.0% R ±22.0% S +22/-33% T +22/-56% U +22/-82% V

Effect of Temperature: Both capacitance and dissipa- tion factor are affected by variations in temperature. The max- imum capacitance change with temperature is defined by the temperature characteristic. However, this only defines a “box” bounded by the upper and lower operating temperatures and the minimum and maximum capacitance values. Within this “box”, the variation with temperature depends upon the spe- cific dielectric formulation. Typical curves for KEMET capaci- tors are shown in Figures 3, 4, and 5. These figures also include the typical change in dissipation factor for KEMET capacitors. Insulation r esistance decr eases with temperatur e. Typically, the insulation resistance at maximum rated temper- ature is 10% of the 25° C value. Effect of V oltage: Class I ceramic capacitors ar e not affected by variations in applied AC or DC voltages. For Class II and III ceramic capacitors, variations in voltage affect only the capacitance and dissipation factor. The application of DC voltage higher than 5 vdc reduces both the capacitance and dissipation factor. The application of AC voltages up to 10-20 Vac tends to increase both capacitance and dissipation factor. At higher AC voltages, both capacitance and dissipation factor begin to decrease. Typical curves showing the effect of applied AC and DC voltage are shown in Figure 6 for KEMET X7R capacitors and Figure 7 for KEMET Z5U capacitors. Effect of Frequency: Frequency affects both capaci- tance and dissipation factor. Typical curves for KEMET multi- layer ceramic capacitors are shown in Figures 8 and 9. The variation of impedance with frequency is an impor- tant consideration in the application of multilayer ceramic capacitors. Total impedance of the capacitor is the vector of the capacitive reactance, the inductive reactance, and the ESR, as illustrated in Figure 2. As frequency increases, the capacitive reactance decreases. However, the series inductance (L) shown in Figure 1 produces inductive reactance, which increases with frequency. At some frequency, the impedance ceases to be capacitive and becomes inductive. This point, at the bottom of the V-shaped impedance versus frequency curves, is the self-resonant frequency. At the self-resonant fre- quency, the reactance is zero, and the impedance consists of the ESR only. Typical impedance versus frequency curves for KEMET multilayer ceramic capacitors ar e shown in Figures 10, 11, and 12. These curves apply to KEMET capacitors in chip form, with- out leads. Lead configuration and lead length have a significant impact on the series inductance. The lead inductance is approximately 10nH/inch, which is large compared to the inductance of the chip. The effect of this additional inductance is a decr ease in the self-r esonant frequency, and an increase in impedance in the inductive region above the self-resonant frequency. Effect of Time: The capacitance of Class II and III dielectrics change with time as well as with temperatur e, volt- age and frequency. This change with time is known as “aging.” It is caused by gradual r ealignment of the crystalline structur e of the ceramic dielectric material as it is cooled below its Curie temperature, which produces a loss of capacitance with time. The aging process is predictable and follows a logarithmic decay. Typical aging rates for C0G, X7R, and Z5U dielectrics are as follows: C0G None X7R 2.0% per decade of time Z5U 5.0% per decade of time Typical aging curves for X7R and Z5U dielectrics are shown in Figure 13. The aging process is reversible. If the capacitor is heat- ed to a temperature above its Curie point for some period of time, de-aging will occur and the capacitor will regain the capacitance lost during the aging process. The amount of de- aging depends on both the elevated temperatur e and the length of time at that temperature. Exposure to 150°C for one- half hour or 125°C for two hours is usually sufficient to return the capacitor to its initial value. Because the capacitance changes rapidly immediately after de-aging, capacitance measurements are usually delayed for at least 10 hours after the de-aging process, which is often referred to as the “last heat.” In addition, manufacturers utilize the aging rates to set factory test limits which will bring the capacitance within the specified tolerance at some future time, to allow for customer receipt and use. Typically, the test limits are adjusted so that the capacitance will be within the specified tolerance after either 1,000 hours or 100 days, depending on the manufacturer and the product type. © KEMET Electronics Corporation, P .O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 7 Application Notes APPLICATION NOTES FOR MULTILAYER CERAMIC CAPACITORS

APPLICATION NOTES FOR MULTILAYER CERAMIC CAPACITORS © KEMET Electronics Corporation, P .O. Box 5928, Greenville, S.C. 29606, (864) 963-63008 POWER DISSIPATION Power dissipation has been empirically determined for two representative KEMET series: C052 and C062. Power dis- sipation capability for various mounting configurations is shown in Table 3. This table was extracted from Engineering Bulletin F-2013, which provides a more detailed treatment of this sub- ject. Note that no significant difference was detected between the two sizes in spite of a 2 to 1 surface area ratio. Due to the materials used in the construction of multilayer ceramic capac- itors, the power dissipation capability does not depend greatly on the surface area of the capacitor body, but rather on how well heat is conducted out of the capacitor lead wires. Consequently, this power dissipation capability is applicable to other leaded multilayer styles and sizes. TABLE 3 POWER DISSIPATION CAPABILITY (Rise in Celsius degrees per Watt) Power Mounting Configuration Dissipation of C052 & C062 1.00" leadwires attached to binding post 90 Celsius degrees of GR-1615 bridge (excellent heat sink) rise per Watt ±10% 0.25" leadwires attached to binding post 55 Celsius degrees of GR-1615 bridge rise per Watt ±10% Capacitor mounted flush to 0.062" glass- 77 Celsius degrees epoxy circuit board with small copper traces rise per Watt ±10% Capacitor mounted flush to 0.062" glass- 53 Celsius degrees epoxy circuit board with four square inches rise per Watt ±10% of copper land area as a heat sink As shown in Table 3, the power dissipation capability of the capacitor is very sensitive to the details of its use environ- ment. The temperature rise due to power dissipation should not exceed 20° C. Using that constraint, the maximum permissible power dissipation may be calculated from the data provided in Table 3. It is often convenient to translate power dissipation capa- bility into a permissible AC voltage rating. Assuming a sinu- soidal wave form, the RMS “ripple voltage” may be calculated The data necessary to make this calculation is included in Engineering Bulletin F-2013. However , the following criteria must be observed: 1. The temperature rise due to power dissipation should be limited to 20° C. 2. The peak AC voltage plus the DC voltage must not exceed the maximum working voltage of the capacitor. Provided that these criteria ar e met, multilayer ceramic E = Z x Where E = RMS Ripple V oltage (volts) P = Power Dissipation (watts) Z = Impedanc e R = ESR PMAX R capacitors may be operated with AC voltage applied without need for DC bias. RELIABILITY A well constructed multilayer ceramic capacitor is extremely reliable and, for all practical purposes, has an infi- nite life span when used within the maximum voltage and temperature ratings. Capacitor failure may be induced by sus- tained operation at voltages that exceed the rated DC voltage, voltage spikes or transients that exceed the dielectric with- standing voltage, sustained operation at temperatures above the maximum rated temperature, or the excessive tempera- ture rise due to power dissipation. Failure rate is usually expressed in terms of percent per 1,000 hours or in FITS (failure per billion hours). Some KEMET series are qualified under U.S. military established reliability specifications MIL-PRF-20, MIL-PRF-123, MIL- PRF-39014, and MIL-PRF-55681. Failure rates as low as 0.001% per 1,000 hours are available for all capacitance / voltage ratings covered by these specifications. These spec- ifications and accompanying Qualified Products List should be consulted for details. For series not covered by these military specifications, an internal testing program is maintained by KEMET Quality Assurance. Samples from each week’s production are sub- jected to a 2,000 hour accelerated life test at 2 x rated voltage and maximum rated temperature. Based on the results of these tests, the average failure rate for all non-military series covered by this test program is currently 0.06% per 1,000 hours at maximum rated conditions. The failure rate would be much lower at typical use conditions. For example, using MIL- HDBK-217D this failure rate translates to 0.9 FITS at 50% rated voltage and 50°C. Current failure rate details for specific KEMET multilay- er ceramic capacitor series are available on request. MISAPPLICATION Ceramic capacitors, like any other capacitors, may fail if they are misapplied. Typical misapplications include expo- sure to excessive voltage, current or temperature. If the dielectric layer of the capacitor is damaged by misapplication the electrical energy of the circuit can be released as heat, which may damage the circuit board and other components as well. If potential for misapplication exists, it is recommended that precautions be taken to protect personnel and equipment during initial application of voltage. Commonly used precau- tions include shielding of personnel and sensing for excessive power drain during board testing. STORAGE AND HANDLING Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other envir onments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be degraded by high temperatur e – reels may soften or warp, and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40˚ C, and maximum storage humidity not exceed 70% rela- tive humidity. In addition, temperature fluctuations should be minimized to avoid condensation on the parts, and atmos- pheres should be fr ee of chlorine and sulfur bearing com- pounds. For optimized solderability, chip stock should be used promptly, preferably within 1.5 years of receipt. from the following formula:

© KEMET Electronics Corporation, P .O. Box 5928, Greenville, S.C. 29606, (864) 963-630010 CERAMIC CONFORMALLY COATED/AXIAL “AXIMAX” GENERAL SP ECIFICATIONS Wo rkin g Voltage: Axia l (WVDC ) C0G 50 , 100, 200 X7R 25, 50 , 100, 200, 250 Z5U 50, 100 Radial (WVDC ) C0G 50 , 100, 200, 50 0, 1k, 1.5k, 2k, 2.5k, 3k X7R 25, 50 , 100, 200, 250, 500, 1k, 1.5k, 2k, 2.5k, 3k Z5U 50, 100 Temperature Charac teristics: C0G 0 ± 30 PPM / °C f rom -55°C to +125°C (1) X7R ± 15% f rom -55°C to +125°C Z5U + 22%, -56% f rom +10°C to +85°C Capacitance T olerance : Con struction : Epo xy encapsul ated – mee ts flame test requi rements of UL St andard 94 V-0. High-tempe rature solde r – meets EIA RS-198, Method 302, Condition B (260°C for 10 seconds) Lead Material: St andard: 100% matte tin (Sn ) with nickel (Ni) underplate and steel core ( “T A” de signatio n). Alternative 1: 60% Tin (Sn)/40% Lead (P b) f inish with coppe r- cl ad steel core ( “HA” de signation). Alternative 2: 60% Tin (Sn)/40% Lead (P b) f inish with 100 % cop per core (avail able with “HA” termination code with c-spe c) Sol derabili ty: EIA RS-198, Method 301, Sol der Temperature: 230 °C ±5°C. Dwe ll time in sol der = 7 ± seconds. Terminal Strength: EIA RS-198, Method 303, Con dition A (2.2kg) ELECTRICAL Capacitance @ 25°C: Wi thin specified tolerance and follo wing test con ditions. C0G – >1000 pF with 1.0 vrms @ 1 kHz 1000pF with 1.0 vrms @ 1 MHz X7R – with 1.0 vrms @ 1 kHz (Referee Time: 1,000 hou rs ) Z5U – with 1.0 vrms @ 1 kHz Dissipation Fac tor @25°C: Same tes t conditions as capa citance. C0G – 0.10% maximum X7R – 2.5% maximum (3.5% for 25 V) Z5U – 4.0% maximum In sul atio n Resistance @25°C: EIA RS-198, Method 104, Con dition A <1kV C0G – 100 G or 1000 M – F, whichever is less. 500V test @ rated voltage , >500V test @ 500V X7R – 10 0 G or 1000 M – F, whiche ver is less. 500V test @ rated voltage , >500V test @ 500V Z5U – 10 G or 1000 M – F, whichever is less. Dielec tric Wi thstandin g Voltage: EIA RS-198, Method 103 250V test @ 250% of rated voltage for 5 second s with curr ent limited to 50mA. 500V test @ 150% of rated voltage f or 5 second s with curr ent limited to 50mA. 1000V test @ 120% of rated voltage f or 5 seconds with curr ent limited to 50mA. ENVIRONMENTAL Vib ratio n: with curr ent limited to 50mA. ENVIRONMENTAL Vib ratio n: EIA RS-198, Method 304 , Con dition D (10-2000Hz; 20g) S ho ck: EIA RS-198, Method 305, Con dition I (100g) Li fe T est: EIA RS-198, Method 201, Con dition D. <200 V C0G – 200% of rated voltage @ +12 5°C X7R – 200% of rated voltage @ +125°C Z5U – 200 % of rated voltage @ +85°C >500V C0G – rated voltage @ +125°C X7R – rated voltage @ +125°C Post Test Limits @ 25°C are: Capacitance Change: C0G ( 200 V) – ±3% or 0.25pF, whiche ver is greater. C0G ( 500 V) – ±3% or 0.50pF, whiche ver is greater. X7R – ± 20% of initial value (2) Z5U – ± 30% of initial value (2) Dissipation Fac tor: C0G – 0.10% maximum X7R – 2.5% maximum (3.5% for 25 V) Z5U – 4.0% maximum In sul atio n Resistance: C0G – 10 G or 100 M – F, whichever is less. >1kV tested @ 500V. X7R – 10 G or 10 0 M – F, whichever is less. >1kV tested @ 500V. Z5U – 1 G or 100 M – F, whichever is less. Moisture Resistance : EIA RS-198, Method 204, Con dition A (10 cycles wit hou t appl ied vol tage). Post Test Limits @ 25°C are: Capacitance Change: C0G ( 200 V) – ±3% or ±0.25pF, whiche ver is greater. C0G ( 500 V) – ±3% or ± 0.50pF, whichever is grea ter. X7R – ± 20% of initial value (2) Z5U – ± 30% of initial value (2) Dissipation Fac tor: C0G – 0.10% maximum X7R – 2.5% maximum (3.5% for 25 V) Z5U – 4.0% maximum In sul atio n Resistance: C0G – 10 G or 100 M – Fwhiche ver is less . 500V test @ rated voltage , >500V test @ 500V. X7R – 10 G or 10 0 M – F, whichever is less . 500V test @ rated voltage , >500V test @ 500V. Z5U – 1k M or 100 M – F, whiche ver is less. Th ermal Sho ck: EIA RS-198 , Method 202, Condi tion B (C0G & X7R: - 55 °C to 125 °C); Cond itio n A (Z5U: -55°C to 85 °C) (1) +53 PPM -30 PPM/ ° C f rom +25 °C t o -55 °C , + 60 PPM be low 10p F. (2) X7R and Z5U dielectrics exhibit aging cha racteristics; t he refore, it is highly recomm ende d t ha t capacitors be de aged for 2 hou rs at 150 °C and stabilized at roo m t empe rature for 48 hours be fore capa citance mea suremen ts are made .

© KEMET Electronics Corporation, P .O. Box 5928, Greenville, S.C. 29606, (864) 963-630022 CERAMIC CONFORMALLY COATED/RADIAL HIGH VOLTAGE “GOLD MAX” DIMENSIONS - INCHES (MILLIMETERS) For packaging information, see pages 47, and 48. MARKING INFORMATION K6D 102K K6DR 103K K6G 102K 1000V 0814 KEMET Series Capacitance, Tolerance Voltage Capacitance, Tolerance Dielectric VoltageSeries KEMET Capacitance, Tolerance VoltageSeries KEMET Rated Voltage Date Code C617 & C62X C63X C64X, C65X, C66X Front View Back View CAPACITOR OUTLINE DRAWING LL Minimum S (Nominal) Lead Spacing ±.030 (.762) LD (Nominal) +.004 (.10) -.001 (.025) Case Size L MAX H MAX T MAX

ORDERING INFORMATION

C – Standard CAPACITANCE PICOFARAD CODE Expressed in picofarads (pF). First two digits represent significant figures. Third digit specifies number of zeros. Use 9 for 1.0 thru 9.9 pF. Example 2.2pF = 229 CAPACITANCE TOLERANCE K – ±10%; M – ±20% Z – -20,+80% RATED VOLTAGE (DC) C – 500 G – 2000 D – 1000 Z – 2500 F – 1500 H – 3000 FAILURE RATE A – Not Applicable LEAD MATERIAL T – 100% Tin (Sn) - RoHS) H – 60/40 Tin (Sn)/Lead (Pb) INTERNAL CONSTRUCTION 5 – Multilayer DIELECTRIC EIA Designation G – C0G (NP0) - Ultra Stable R – X7R - Stable

© KEMET Electronics Corporation, P .O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 23 1.0p F 10 9 C,D 1. 5 15 9 C,D 2. 2 22 9 C,D 2. 7 27 9 C,D 3. 3 33 9 C,D 3. 9 C,D 4. 7 47 9 C,D 5. 6 56 9 C,D 6. 8 C,D 8. 2 C,D 10 10 0 J,K,M 12 12 0 J,K,M 15 15 0 J,K,M 18 18 0 J,K,M 22 22 0 J,K,M 27 27 0 J,K,M 33 33 0 J,K,M 39 39 0 J,K,M 47 47 0 J,K,M 56 56 0 J,K,M 68 68 0 J,K,M 82 82 0 J,K,M 10 0 10 1 J,K,M 12 0 12 1 J,K,M 15 0 15 1 J,K,M 18 0 18 1 J,K,M 22 0 22 1 J,K,M 27 0 27 1 J,K,M 33 0 33 1 J,K,M 39 0 39 1 J,K,M 47 0 47 1 J,K,M 56 0 56 1 J,K,M 68 1 J,K,M 82 0 82 1 J,K,M 100 0 10 2 J,K,M 120 0 12 2 J,K,M 150 0 15 2 J,K,M 180 0 18 2 J,K,M 220 0 22 2 J,K,M 270 0 27 2 J,K,M 330 0 33 2 J,K,M 390 0 39 2 J,K,M 470 0 47 2 J,K,M 560 0 56 2 J,K,M 680 0 68 2 J,K,M 820 0 82 2 J,K,M .010u F 10 3 J,K,M .01 2 12 3 J,K,M .01 5 15 3 J,K,M .01 8 18 3 J,K,M .02 2 22 3 J,K,M .02 7 27 3 J,K,M .03 3 33 3 J,K,M .03 9 39 3 J,K,M .04 7 47 3 J,K,M .05 6 56 3 J,K,M .06 8 68 3 J,K,M .08 2 82 3 J,K,M .1 0 10 4 J,K,M CDVWC DVW C617 )3,2=X() 8,7=X( C62X C62X Cap Code Cap CDVWCDVWC DVW X36CX 36C (X=0,1 ) (X=7, 8) Style Cap Tol Goldmax HV C6XX Series Special Lead Spacing per M49467 - C0G 680 399 689 829 RATINGS & PART NUMBER REFERENCE — C0G/NP0 High Voltage Gold Max CERAMIC CONFORMALLY COATED/RADIAL HIGH VOLTAGE “GOLD MAX” Note: C6xx Series are commercial parts that meet special lead spacing r equirements per MIL-PRF-49467. Group A inspection per MIL-PRF-49467 is available upon r equest. For packaging information, see pages 47 and 48.

© KEMET Electronics Corporation, P .O. Box 5928, Greenville, S.C. 29606, (864) 963-630024 CERAMIC CONFORMALLY COATED/RADIAL HIGH VOLTAGE “GOLD MAX” 50 0 1k 2k 3k 50 0 1k 2k 3k 50 0 1k 2k 3k 50 0 1k 2k 3k 50 01 k2 k 3k 1.0p F 10 9 J,K,M 1. 5 15 9 J,K,M 2. 2 22 9 J,K,M 2. 7 27 9 J,K,M 3. 3 33 9 J,K,M 3. 9 J,K,M 4. 7 47 9 J,K,M 5. 6 56 9 J,K,M 6. 8 J,K,M 8. 2 J,K,M 10 10 0 J,K,M 12 12 0 J,K,M 15 15 0 J,K,M 18 18 0 J,K,M 22 22 0 J,K,M 27 27 0 J,K,M 33 33 0 J,K,M 39 39 0 J,K,M 47 47 0 J,K,M 56 56 0 J,K,M 68 68 0 J,K,M 82 82 0 J,K,M 10 0 10 1 J,K,M 12 0 12 1 J,K,M 15 0 15 1 J,K,M 18 0 18 1 J,K,M 22 0 22 1 J,K,M 27 0 27 1 J,K,M 33 0 33 1 J,K,M 39 0 39 1 J,K,M 47 0 47 1 J,K,M 56 0 56 1 J,K,M 68 1 J,K,M 82 0 82 1 J,K,M 100 0 10 2 J,K,M 120 0 12 2 J,K,M 150 0 15 2 J,K,M 180 0 18 2 J,K,M 220 0 22 2 J,K,M 270 0 27 2 J,K,M 330 0 33 2 J,K,M 390 0 39 2 J,K,M 470 0 47 2 J,K,M 560 0 56 2 J,K,M 680 0 68 2 J,K,M 820 0 82 2 J,K,M .010u F 10 3 J,K,M .01 2 12 3 J,K,M .01 5 15 3 J,K,M .01 8 18 3 J,K,M .02 2 22 3 J,K,M .02 7 27 3 J,K,M .03 3 33 3 J,K,M .03 9 39 3 J,K,M .04 7 47 3 J,K,M .05 6 56 3 J,K,M .06 8 68 3 J,K,M .08 2 82 3 J,K,M .1 0 10 4 J,K,M WVDC Cap Cap Code CDVWC DVWC DVWC DVW C64X (X=0,1) C66X Cap Tol Style Goldmax HV C6XX Series Special Lead Spacing per M49467 - C0G cont. (X=7, 8) X46CX 56CX46C 680 399 689 829 RATINGS & PART NUMBER REFERENCE - C0G/NP0 Note: C6xx Series are commercial parts that meet special lead spacing r equirements per MIL-PRF-49467. Group A inspection per MIL-PRF-49467 is available upon r equest. For packaging information, see pages 47 and 48.

© KEMET Electronics Corporation, P .O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 25 10p F 10 0 K,M,P,Z 12 12 0 K,M,P,Z 15 15 0 K,M,P,Z 18 18 0 K,M,P,Z 22 22 0 K,M,P,Z K,M,P,Z 33 33 0 K,M,P,Z 39 39 0 K,M,P,Z 47 47 0 K,M,P,Z 56 56 0 K,M,P,Z 68 68 0 K,M,P,Z 82 82 0 K,M,P,Z 10 0 10 1 K,M,P,Z 12 0 12 1 K,M,P,Z 15 0 15 1 K,M,P,Z 18 0 18 1 K,M,P,Z 22 0 22 1 K,M,P,Z 27 0 27 1 K,M,P,Z 33 0 33 1 K,M,P,Z 39 0 39 1 K,M,P,Z 47 0 47 1 K,M,P,Z 56 0 56 1 K,M,P,Z 68 0 68 1 K,M,P,Z 82 0 82 1 K,M,P,Z 100 0 10 2 K,M,P,Z 120 0 12 2 K,M,P,Z 150 0 15 2 K,M,P,Z 180 0 18 2 K,M,P,Z 220 0 22 2 K,M,P,Z 270 0 27 2 K,M,P,Z 330 0 33 2 K,M,P,Z 390 0 39 2 K,M,P,Z 470 0 47 2 K,M,P,Z 560 0 56 2 K,M,P,Z 680 0 68 2 K,M,P,Z 820 0 82 2 K,M,P,Z .010u F 10 3 K,M,P,Z .01 2 12 3 K,M,P,Z .01 5 15 3 K,M,P,Z .01 8 18 3 K,M,P,Z .02 2 22 3 K,M,P,Z .02 7 27 3 K,M,P,Z .03 3 33 3 K,M,P,Z .03 9 39 3 K,M,P,Z .04 7 47 3 K,M,P,Z .05 6 56 3 K,M,P,Z .06 8 68 3 K,M,P,Z .08 2 82 3 K,M,P,Z .1 0 10 4 K,M,P,Z .1 2 12 4 K,M,P,Z .1 5 15 4 K,M,P,Z .1 8 18 4 K,M,P,Z .2 2 22 4 K,M,P,Z .2 7 27 4 K,M,P,Z .3 3 33 4 K,M,P,Z .3 9 39 4 K,M,P,Z .4 7 47 4 K,M,P,Z .5 6 56 4 K,M,P,Z .6 8 68 4 K,M,P,Z .8 2 82 4 K,M,P,Z 1. 0 10 5 K,M,P,Z 1. 2 12 5 K,M,P,Z 1. 5 15 5 K,M,P,Z 1. 8 18 5 K,M,P,Z 2. 2 22 5 K,M,P,Z 2. 7 27 5 K,M,P,Z C63X Cap Cap Code CDVWC DVWC DVW X36CX26C C62X WVDC (X=7, 8 ) (X=0,1) WVDC Style Cap Tol (X=2, 3) Goldmax HV C6XX Series Special Lead Spacing per M49467 - X7R C617 (X=7, 8) 270 27 RATINGS & PART NUMBER REFERENCE - X7R High Voltage Gold Max CERAMIC CONFORMALLY COATED/RADIAL HIGH VOLTAGE “GOLD MAX” Note: C6xx Series are commercial parts that meet special lead spacing requirements per MIL-PRF-49467. Group A inspection per MIL-PRF-49467 is available upon request. For packaging information, see pages 47 and 48.

© KEMET Electronics Corporation, P .O. Box 5928, Greenville, S.C. 29606, (864) 963-630026 CERAMIC CONFORMALLY COATED/RADIAL HIGH VOLTAGE “GOLD MAX” 50 0 1k 2k 3k 50 0 1k 2k 3k 50 0 1k 2k 3k 50 0 1k 2k 3k 50 0 1k 2k 3k 10p F 10 0 K,M,P,Z 12 12 0 K,M,P,Z 15 15 0 K,M,P,Z 18 18 0 K,M,P,Z 22 22 0 K,M,P,Z 17 27 0 K,M,P,Z 33 33 0 K,M,P,Z 39 39 0 K,M,P,Z 47 47 0 K,M,P,Z 56 56 0 K,M,P,Z 68 68 0 K,M,P,Z 82 82 0 K,M,P,Z 10 0 10 1 K,M,P,Z 12 0 12 1 K,M,P,Z 15 0 15 1 K,M,P,Z 18 0 18 1 K,M,P,Z 22 0 22 1 K,M,P,Z 27 0 27 1 K,M,P,Z 33 0 33 1 K,M,P,Z 39 0 39 1 K,M,P,Z 47 0 47 1 K,M,P,Z 56 0 56 1 K,M,P,Z 68 0 68 1 K,M,P,Z 82 0 82 1 K,M,P,Z 100 0 10 2 K,M,P,Z 120 0 12 2 K,M,P,Z 150 0 15 2 K,M,P,Z 180 0 18 2 K,M,P,Z 220 0 22 2 K,M,P,Z 270 0 27 2 K,M,P,Z 330 0 33 2 K,M,P,Z 390 0 39 2 K,M,P,Z 470 0 47 2 K,M,P,Z 560 0 56 2 K,M,P,Z 680 0 68 2 K,M,P,Z 820 0 82 2 K,M,P,Z .010u F 10 3 K,M,P,Z .01 2 12 3 K,M,P,Z .01 5 15 3 K,M,P,Z .01 8 18 3 K,M,P,Z .02 2 22 3 K,M,P,Z .02 7 27 3 K,M,P,Z .03 3 33 3 K,M,P,Z .03 9 39 3 K,M,P,Z .04 7 47 3 K,M,P,Z .05 6 56 3 K,M,P,Z .06 8 68 3 K,M,P,Z .08 2 82 3 K,M,P,Z .1 0 10 4 K,M,P,Z .1 2 12 4 K,M,P,Z .1 5 15 4 K,M,P,Z .1 8 18 4 K,M,P,Z .2 2 22 4 K,M,P,Z .2 7 27 4 K,M,P,Z .3 3 33 4 K,M,P,Z .3 9 39 4 K,M,P,Z .4 7 47 4 K,M,P,Z .5 6 56 4 K,M,P,Z .6 8 68 4 K,M,P,Z .8 2 82 4 K,M,P,Z 1. 0 10 5 K,M,P,Z 1. 2 12 5 K,M,P,Z 1. 5 15 5 K,M,P,Z 1. 8 18 5 K,M,P,Z 2. 2 22 5 K,M,P,Z 2. 7 27 5 K,M,P,Z Cap Tol Style WVD C WVDC X46C X46C X46C Cap Cap Code (X=7, 8) CDVWC DVWC DVW C65X Goldmax HV C6XX Series Special Lead Spacing per M49467 - X7R cont. C66X RATINGS & PART NUMBER REFERENCE - X7R Note: C6xx Series are commercial parts that meet special lead spacing requirements per MIL-PRF-49467. Group A inspection per MIL-PRF-49467 is available upon request. For packaging information, see pages 47 and 48.

© KEMET Electronics Corporation, P .O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 47 Tape and Reel Packaging CERAMIC LEADED PACKAGING INFORMATION

© KEMET Electronics Corporation, P .O. Box 5928, Greenville, S.C. 29606, (864) 963-630048 CERAMIC LEADED PACKAGING INFORMATION KEMET Series Military Style Military Specification Standard (1) Bulk Quantity Ammo Pack Quantity Maximum Maximum Reel Quantity Reel Size C114C-K-G CK12, CC75 MIL-C- 11015/ 200/Box 5000 12" C124C-K-G CK13, CC76 MIL-PRF-20 200/Box 5000 12" C192C-K-G CK14, CC77 100/Box 3000 12" C202C-K CK15 25/Box 500 12" C222C-K CK16 10/ Tray 300 12" C052C-K-G CK05, CC05 100/Bag 2000 2000 12" C062C-K-G CK06, CC06 100/Bag 1500 1500 12" C114G CCR75 MIL-PRF-20 200/Box 5000 12" C124G CCR76 200/Box 5000 12" C192G CCR77 100/Box 3000 12" C202G CC78-CCR78 25/Box 500 12" C222G CC79-CCR79 10/ Tray 300 12" C052/56G CCR05 100/Bag 1700 12" C062/66G CCR06 100/Bag 1500 12" C512G CC07-CCR07 Footnote (2) N/A N/A C522G CC08-CCR08 Footnote (2) N/A N/A C114T CKR 11 MIL-PRF-39014 200/Box 5000 12" C124T CKR12 200/Box 5000 12" C192T CKR14 100/Box 3000 12" C202T CKR15 25/Box 500 12" C222T CKR16 10/ Tray 300 12" C052/56T CKR05 100/Bag 1700 12" C062/66T CKR06 100/Bag 1500 12" C31X 500/Bag 2500 2500 12" C32X 500/Bag 2500 2500 12" C33X 250/Bag 1500 1500 12" C340 100/Bag 1000 1000 12" C350 50/Bag N/A 500 12" C410 300/Box 4000 5000 12" C412 200/Box 4000 5000 12" C420 300/Box 4000 5000 12" C430 200/Box 2000 2500 12" C440 200/Box 2000 2500 12" C512 N/A N/A Footnote (2) N/A N/A C522 N/A N/A Footnote (2) N/A N/A C617 250/Bag 1000 12" C622/C623 100/Bag 500 12" C627/C628 100/Bag 500 12" C630/C631 100/Bag 500 12" C637/C638 50/Bag 500 12" C640/C641 50/Bag 500 12" C642/C643 50/Bag 500 12" C647/C648 50/Bag 500 12" C657/C658 50/Bag 500 12" C667/C668 50/Bag 500 12" CERAMIC PACKAGING NOTE: (1) Standard packaging refers to number of pieces per bag, tray or vial. (2) Quantity varies. For further details, please consult the factor y.