BT151F PHILIPS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Philips Semiconductors Product specification Thyristors BT151F series GENERAL DESCRIPTION QUICK REFERENCE DATA Glass passivated thyristors in a fullSYMBOL PARAMETER MAX. MAX. MAX. UNIT pack, plastic envelope, intended for use in applications requiring high BT151F- 500 650 800 bidirectional blocking voltage V DRM , Repetitive peak off-state 500 650 800 V capability and high thermal cycling VRRM voltages performance. Typical applications IT(AV) Average on-state current 5.7 5.7 5.7 A include motor control, industrial and IT(RMS) RMS on-state current 9 9 9 A domestic lighting, heating and static ITSM Non-repetitive peak on-state 100 100 100 A switching. current PINNING - SOT186 PIN CONFIGURATION SYMBOL PIN DESCRIPTION 1 cathode 2 anode 3 gate case isolated LIMITING VALUES Limiting values in accordance with the Absolute Maximum System (IEC 134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT -500 -650 -800 VDRM , VRRM Repetitive peak off-state - 500 1 6501 800 V voltages IT(AV) Average on-state current half sine wave; Ths ≤ 87 ˚C - 5.7 A IT(RMS) RMS on-state current all conduction angles - 9 A ITSM Non-repetitive peak half sine wave; Tj = 125 ˚C prior on-state current to surge; with reapplied VDRM(max) t = 10 ms - 100 A t = 8.3 ms - 110 A I2tI 2t for fusing t = 10 ms - 50 A 2s dIT/dt Repetitive rate of rise of ITM = 20 A; IG = 50 mA; - 50 A/ µs on-state current after dIG /dt = 50 mA/µs triggering IGM Peak gate current - 2 A VGM Peak gate voltage - 5 V VRGM Peak reverse gate voltage - 5 V PGM Peak gate power - 5 W PG(AV) Average gate power over any 20 ms period - 0.5 W Tstg Storage temperature -40 150 ˚C Tj Operating junction - 125 ˚C temperature ak g123 case 1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the thyristor may switch to the on-state. The rate of rise of current should not exceed 15 A/µs. February 1996 1 Rev 1.100

Philips Semiconductors Product specification Thyristors BT151F series ISOLATION LIMITING VALUE & CHARACTERISTIC Ths = 25 ˚C unless otherwise specified SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT V isol Repetitive peak voltage from all R.H. ≤ 65% ; clean and dustfree - 1500 V three terminals to external heatsink C isol Capacitance from T2 to external f = 1 MHz - 12 - pF heatsink THERMAL RESISTANCES SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT R th j-hs Thermal resistance with heatsink compound - - 4.5 K/W junction to heatsink without heatsink compound - - 6.5 K/W R th j-a Thermal resistance in free air - 55 - K/W junction to ambient STATIC CHARACTERISTICS Tj = 25 ˚C unless otherwise stated SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT I GT Gate trigger current V D = 12 V; IT = 0.1 A - 2 15 mA IL Latching current V D = 12 V; IGT = 0.1 A - 10 40 mA IH Holding current V D = 12 V; IGT = 0.1 A - 7 20 mA VT On-state voltage I T = 23 A - 1.4 1.75 V VGT Gate trigger voltage V D = 12 V; IT = 0.1 A - 0.6 1.5 V VD = VDRM(max) ; IT = 0.1 A; Tj = 125 ˚C 0.25 0.4 - V ID , IR Off-state leakage current VD = VDRM(max) ; VR = VRRM(max) ; Tj = 125 ˚C - 0.1 0.5 mA DYNAMIC CHARACTERISTICS Tj = 25 ˚C unless otherwise stated SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT dVD /dt Critical rate of rise of VDM = 67% VDRM(max) ; Tj = 125 ˚C; off-state voltage exponential waveform Gate open circuit 50 130 - V/ µs R GK = 100 Ω 200 1000 - V/ µs tgt Gate controlled turn-on ITM = 40 A; VD = VDRM(max) ; IG = 0.1 A; - 2 - µs time dI G /dt = 5 A/µs tq Circuit commutated V D = 67% VDRM(max) ; Tj = 125 ˚C; - 70 - µs turn-off time I TM = 20 A; VR = 25 V; dITM /dt = 30 A/µs; dVD /dt = 50 V/µs; RGK = 100 Ω February 1996 2 Rev 1.100

Philips Semiconductors Product specification Thyristors BT151F series Fig.1. Maximum on-state dissipation, Ptot, versus average on-state current, IT(AV), where a = form factor = IT(RMS) / IT(AV). Fig.2. Maximum permissible non-repetitive peak on-state current ITSM , versus pulse width tp, for sinusoidal currents, tp ≤ 10ms. Fig.3. Maximum permissible rms current IT(RMS) , versus heatsink temperature Ths. Fig.4. Maximum permissible non-repetitive peak on-state current ITSM , versus number of cycles, for sinusoidal currents, f = 50 Hz. Fig.5. Maximum permissible repetitive rms on-state current IT(RMS) , versus surge duration, for sinusoidal currents, f = 50 Hz; Ths ≤ 87˚C. Fig.6. Normalised gate trigger voltage VGT (Tj)/ VGT (25˚C), versus junction temperature Tj. 01234560 a = 1.57 1.9 2.2 2.8 BT151F IF(AV) / A Ptot / W conduction angle form factor degrees 120 180 2.8 2.2 1.9 1.57 125 116 107 80Ths(max) / C a 1 10 100 10000 100 120 BT151 Number of half cycles at 50Hz ITSM / A T ITSM time I Tj initial = 125 C max T 100

1000 BT151

I Tj initial = 125 C max T dI /dt limitT 0.01 0.1 1 100 BT151 surge duration / s IT(RMS) / A -50 0 50 100 1500

10 BT151F

IT(RMS) / A 87 C -50 0 50 100 1500.4 0.6 0.8 1.2 1.4 1.6 BT151 Tj / C VGT(Tj) VGT(25 C) February 1996 3 Rev 1.100

Philips Semiconductors Product specification Thyristors BT151F series Fig.7. Normalised gate trigger current IGT (Tj)/ IGT (25˚C), versus junction temperature Tj. Fig.8. Normalised latching current IL(Tj)/ IL(25˚C), versus junction temperature Tj. Fig.9. Normalised holding current IH (Tj)/ IH (25˚C), versus junction temperature Tj. Fig.10. Typical and maximum on-state characteristic. Fig.11. Transient thermal impedance Zth j-hs, versus pulse width tp. Fig.12. Typical, critical rate of rise of off-state voltage, dVD /dt versus junction temperature Tj. -50 0 50 100 1500 0.5 1.5 2.5

3 BT151

IGT(Tj) IGT(25 C) 0 0.5 1 1.5 20 BT151 VT / V IT / A Tj = 125 C Tj = 25 C Vo = 1.06 V Rs = 0.0304 ohms typ max -50 0 50 100 1500 0.5 1.5 2.5

3 BT145

IL(Tj) IL(25 C) 0.001 0.01 0.1

10 BT151

Zth j-hs (K/W) 10us 0.1ms 1ms 10ms 0.1s 1s 10s tpP t D without heatsink compound with heatsink compound -50 0 50 100 1500 0.5 1.5 2.5 IH(Tj) IH(25 C) 0 50 100 15010 100 1000 10000 Tj / C dVD/dt (V/us) gate open circuit RGK = 100 Ohms February 1996 4 Rev 1.100

Philips Semiconductors Product specification Thyristors BT151F series MECHANICAL DATA Dimensions in mm Net Mass: 2 g Fig.13. SOT186; The seating plane is electrically isolated from all terminals. Notes 1. Accessories supplied on request: refer to mounting instructions for F-pack envelopes. 2. Epoxy meets UL94 V0 at 1/8". 10.2 max 5.7 max 3.2 3.0 0.9 0.5 4.4 max 2.9 max 4.4 4.0 seating plane 7.9 7.5 max 0.55 max 1.3 13.5 min 2.54 5.08 0.9 0.7 123 M0.4 top view 3.5 max not tinned 4.4 February 1996 5 Rev 1.100

Philips Semiconductors Product specification Thyristors BT151F series DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.

Application information

Where application information is given, it is advisory and does not form part of the specification.  Philips Electronics N.V. 1996 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. February 1996 6 Rev 1.100