BK2XX05002

BK2XX05002 YAGEO | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 7

Technical content

RoHS compliant & Halogen free Product specification– July 04, 2023 V.1

www. yageo .com Jul. 04, 2023 V.1 Spark Gap (SPG) Data Sheet

Features

■ Approximately zero leaking current before clamping voltage ■ Less decay at on/off state. ■ High capability to withstand repeated lightning strikes. ■ Low electrode capacitance(≤0.8pF) and high isolation(≥100MΩ). ■ RoHS compliant. ■ Bilateral symmetrical. ■ Temperature, humidity and lightness insensitive. ■ Operating temperature: -40℃ ~ +85℃ ■ Storage temperature: -40℃ ~ +125℃ ■ Meets MSL level 1, per J-STD-020

Applications

■ Power Supplies ■ Motor sparks eliminating ■ Relay switching spark absorbing ■ Data line pulse guarding ■ Telephone/Fax/Modem ■ High frequency signal transmitters/receivers ■ Satellite antenna ■ Radio amplifiers ■ Alarm systems ■ Cathode ray tubes in Monitors/TVs Dimensions Color code 1 Color code 2 Color code 3 D L1 L L1 d Symbol Dimension (mm) L 4.3±0.5 L1 28.0±3.0 D Φ2.6±0.5 d Φ0.5±0.05

www. yageo .com Jul. 04, 2023 V.1

Electrical Characteristics

(1KHz-6VMAX) Surge Current Capacity (8/20μs) Surge Life Test Vs(V) Test Voltage(V) IROHM(MΩ) C(pf) 8/20μs,100A BK22000702 140±20% 50 100 0.8 1000A 200 times BK23000702 140±30% 50 100 0.8 1000A 200 times BK22001002 200±20% 100 100 0.8 1000A 200 times BK22001102 220±20% 100 100 0.8 1000A 200 times BK22001502 300±20% 100 100 0.8 1000A 200 times BK22002002 400±20% 250 100 0.8 1000A 200 times BK22002502 500±20% 250 100 0.8 1000A 200 times BK22003002 600±20% 250 100 0.8 1000A 200 times BK22003502 700±20% 250 100 0.8 1000A 200 times BK22005002 1000±20% 500 100 0.8 1000A 200 times BK22007502 1500±20% 500 100 0.8 1000A 200 times Color Code Part Number Color Code 1 Color Code 2 Color Code 3 BK22000702 Black Yellow - BK23000702 Black Yellow - BK22001002 Red - - BK22001102 Red Red - BK22001502 Orange - - BK22002002 Yellow - - BK22002502 Green - - BK22003002 Blue - - BK22003502 Purple - - BK22005002 Black - - BK22007502 Brown Green Red

www. yageo .com Jul. 04, 2023 V.1 Test Methods and Results Items Test Method Standard DC Spark-over Voltage Measure starting discharge voltage (Vs) by gradually increasing applied DC voltage. Test current is 0.5mA max. And the DC voltage ascends up within 100V/s(Vs＜1000V) or 500V/s(Vs≥1000V). Meet specified value. Insulation Resistance Measure the insulation resistance across the terminal at regular voltage. But the test voltage doesn’t over the DC spark-over voltage. Capacitance Measure the electrostatic capacitance by applying a voltage of less than 6V (at 1KHz) between terminals. Static Life 10KV with 1500pf condenser is discharged through 0Ω resistor. 200 times at an interval of 10sec. ∣△Vs/Vs∣≤30% Characteristics of other items must meet the specified value. Surge Current Capacity The following impulse current for specified current applied ±5 times, each time interval 60 seconds. Thereafter, outer appearance shall be visually examined. Type Impulse current Vs < 400V 1.2/50μs & 8/20μs, 1000A Vs ≥ 400V 1.2/50μs & 8/20μs, 1000A, electrically connected with a resistor (1~2 Ω). No crack and no failures Cold Resistance Measurement after -40℃/1000 HRS & normal temperature/2 HRS. Features are conformed to rated spec. Heat Resistance Measurement after 125℃/1000 HRS & normal temperature/2 HRS. Humidity Resistance Measurement after humidity 90~95℃(45℃) /1000 HRS & normal temperature/2 HRS. Temperature Cycle 10 times repetition of cycle -40℃/30min →normal, temp/2 min →125℃/30min, measurement after normal temp/2 HRS. Solder Ability Apply flux and immerse in molten solder 230±5℃ for 3sec up to the point of 1.5mm from body. Check for solder adhesion. Lead wire is evenly covered by solder. Solder Heat Measurement after lead wire is dipped up to the point of 1.5mm from body into 260±5℃ solder for 10sec. Conformed to rated spec. Pull Strength Apply 0.5kg load for 10sec. Lead shall not pull out to snap. Flexural Strength Bend lead wire at the point of 2mm from body under 0.25 load and back to its original point. Repeat 1 time.

www. yageo .com Jul. 04, 2023 V.1 Recommended Soldering Conditions Flow Soldering Conditions Reflow Soldering Conditions Air Priheat Soldering Cooling Temperature (℃) 250 200 150 100 60~120 sec 3~4 sec 150~180℃ 260℃ Air Priheat Soldering Cooling Temperature (℃) 250 200 150 100 60~120 sec 10 sec. or less 150~180℃ 260℃ 60 sec. or less 1) Time shown in the above figures is measured from the point when chip surface reaches temperature. 2) Temperature difference in high temperature part should be within 110℃. 3) After soldering, do not force cool, allow the parts to cool gradually. Hand Soldering Solder iron temperature: 350±5℃ Heating time: 3 seconds max. General attention to soldering

• High soldering temperatures and long soldering times can cause leaching of the termination, decrease in adherence strength, and the change of characteristic may occur.
• For soldering, please refer to the soldering curves above. However, please keep exposures to temperatures exceeding 200℃ to fewer than 50 seconds.
• Please use a mild flux (containing less than 0.2wt% CI). Also, if the flux is water soluble, be sure to wash thoroughly to remove any residue from the underside of components that could affect resistance. Cleaning When using ultrasonic cleaning, the board may resonate if the output power is too high. Since this vibration can cause cracking or a decrease in the adherence of the termination, we recommend that you use the conditions below. Frequency: 40kHz max. Output power: 20W/liter Cleaning time: 5 minutes max.

www. yageo .com Jul. 04, 2023 V.1 Packaging Tape R L D1 D P Z t L1 L2 TS T S W Symbol Dimension (mm) W 52.0±1.5 P 5.0±0.5 L1-L2 1.0max. T 6.0±1.0 Z 1.2max. R Terminals must not project from tape. t 3.2max. S 0.8max. D Φ3.1max. D1 Φ0.5±0.05 L 4.8max. Inner Box C A B A 74.0±5.0 B 77.0±5.0 C 252.0±5.0 Quantity: 2500PCS

www.yageo.com Circuit Protection Components Product specification LEGAL DISCLAIMER YAGEO, its distributors and agents (collectively, “YAGEO”), hereby disclaims any and all liabilities for any errors, inaccuracies or incompleteness contained in any product related information, including but not limited to product specifications, datasheets, pictures and/or graphics. YAGEO may make changes, modifications and/or improvements t o product related information at any time and without notice. YAGEO makes no representation, warranty, and/or guarantee about the fitness of its products for any particular purpose or the continuing production of any of its products. To the maximum exten t permitted by law, YAGEO disclaims (i) any and all liability arising out of the application or use of any YAGEO product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied w arranties, including warranties of fitness for a particular purpose, non -infringement and merchantability. YAGEO products are designed for general purpose applications under normal operation and usage conditions. Please contact YAGEO for the application s listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property: Aerospace equipment (artificial satellite, rocket, etc.), Atomic energy -related equipment, Aviation equipment, Disaster prevention equipment, crime prevention equipment, Electric heating apparatus, burning equipment, Highly public information network equipment, data -processing equipment , Medical devices, Military equipment, Power generation co ntrol equipment, Safety equipment, Traffic signal equipment, Transportation equipment and Undersea equipment, or for any other application or use in which the failure of YAGEO products could result in personal injury or death, or serious property damage. P articularly YAGEO Corporation and its affiliates do not recommend the use of commercial or automotive grade products for high reliability applications or manned space flight. Information provided here is intended to indicate product specifications only. YAGEO reserves all the rights for revising this content without further notification, as long as products are unchanged. Any product change will be announced by PCN.