DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 12
Technical content
Evaluation Board User Guide UG-250 Evaluation Board for 16-Bit, Serial Input, Loop-Powered 4 mA to 20 mA DAC PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. A | Page 1 of 12
FEATURES
Full-featured evaluation board for the AD5421 Link options PC control in conjunction with Analog Devices, Inc., system demonstration platform (SDP) PC software for control EQUIPMENT NEEDED DC power supply unit SDP for PC control (EVAL-SDP-CB1Z) Voltmeter or ammeter DOCUMENTS NEEDED AD5421 data sheet SOFTWARE NEEDED AD5421 evaluation software EVALUATION BOARD DESCRIPTION The EV AL-AD5421 is a full-featured evaluation board, designed to allow the user to easily evaluate all features of the AD5421 loop-powered 4 mA to 20 mA DAC. The AD5421 pins are accessible at on-board connectors for external connection. The AD5421 evaluation board is controlled via the PC’s USB port in conjunction with Analog Device’s system demonstration platform board. The SDP board allows the evaluation board to be controlled through the USB port of a Windows® XP (SP2 or later) or Vista-based (32-bit) PC using the AD5421 evaluation software. The AD5421 serial interface is also accessible at the testpoint connections on the board. DEVICE DESCRIPTION The AD5421 is an integrated device designed for use in loop- powered 4 mA to 20 mA smart transmitter applications. The AD5421, in a single chip, provides a 16-bit DAC and current amplifier for digital control of the loop current, a voltage regulator to power the entire transmitter, a voltage reference, fault alert functions, flexible SPI-compatible serial interface, gain and offset adjust registers as well as other features and functions. Complete specifications for the AD5421 are available in the AD5421 data sheet available from Analog Devices and should be consulted in conjunction with this document when using the evaluation board. FUNCTIONAL BLOCK DIAGRAM SYSTEM DEMONSTRATION PLATFORM BOARD PC USB PORT LOOP+ LOOP– DIGITAL ISOLATION AD5421 EVAL-AD5421SDZ 09701-001 Figure 1.
UG-250 Evaluation Board User Guide Rev. A | Page 2 of 12 TABLE OF CONTENTS
REVISION HISTORY
10/11—Rev. 0 to Rev. A 3/11—Revision 0: Initial Version
case is 240 V . A load resistor can also be connected at J7. of the link options are described in Table 2. The default link options are listed in Table 1. Table 1. Link Options
Table 2. Link Options LK1 This link connects the VLOOP input pin to the LOOP+ voltage via a 20:1 resistor divider. When this link is inserted, the VLOOP pin is connected to the resistor divider. When this link is removed, the VLOOP pin is unconnected and can be connected to another voltage (maximum 2.5 V) via TP26. LK2 This link enables/disables the MOSFET device. Position A disables the MOSFET device. Position B enables the MOSFET device and the loop supply is connected directly to the REGIN pin. LK4 This link enables/disables the iCoupler® digital isolators. When this link is inserted, the isolators are enabled. When this link is removed, the isolators are disabled. LK6 This link should be inserted when the MOSFET device is enabled (LK2 in Position B). This link should be removed when the MOSFET device is disabled (LK2 in Position A). LK7 This link completes the loop connection if a load resistor is not connected at Connector J7. This link should be inserted if a load resistor is not connected at Connector J7. This link should be removed if a load resistor is connected at Connector J7. Alarm_Dir This link selects the alarm current direction. Position A selects an upscale alarm current (22.8 mA or 24 mA). Position B selects a downscale alarm current (3.2 mA). Rint_Rext This link selects to use either the internal or external current setting resistor. Position A selects the internal resistor. Position B selects the external resistor. These links select the loop current range. These links select the voltage regulator output voltage.
can run setup.exe from the CD.
- After installation from the CD is complete, power up the
- Connect the SDP board to the AD5421 evaluation board
cable. Either connector of the SDP board may be used.
- When the evaluation system is detected, proceed through
any dialog boxes that appear. This finishes the installation.
- From the Start menu, select Analog Devices – AD5421;
window of the software displays (see Figure 3).
- If the evaluation system is not connected to the USB port
click Rescan, and follow the instructions. Figure 2. Connectivity Error Alert
Figure 3. Main Window allows the user to program the control register. register, offset adjust register, and gain adjust register. the Range0 and Range1 link options. AD5421s registers as well as issue commands.
Figure 4. Schematic of the AD5421 Circuitry
Figure 5. Schematic of the SDP Board Connector
Figure 8. Solder Side PCB Drawing
Evaluation Board User Guide UG-250 Rev. A | Page 11 of 12
ORDERING INFORMATION
Table 3. Reference Designator Part Description Part Number Supplier/Number C5 Capacitor, F/TERM, 100 nF, 50 V, X7R 06035C104KAZ2A FEC 1301894 C6 Capacitor, F/TERM, 100 nF, 50 V, X7R 06035C104KAZ2A FEC 1301894 C7 Capacitor, F/TERM, 100 nF, 50 V, X7R 06035C104KAZ2A FEC 1301894 C8 Capacitor, F/TERM, 100 nF, 50 V, X7R 06035C104KAZ2A FEC 1301894 C9 Capacitor, F/TERM, 100 nF, 50 V, X7R 06035C104KAZ2A FEC 1301894 C10 Capacitor, F/TERM, 100 nF, 50 V, X7R 06035C104KAZ2A FEC 1301894 C11 Capacitor, 1 µF, 16 V, Case A tantalum MCCTA105M016 FEC 1190114 C12 Capacitor, F/TERM, 100 nF, 50 V, X7R 06035C104KAZ2A FEC 1301894 C13 Capacitor, F/TERM, 100 nF, 50 V, X7R 06035C104KAZ2A FEC 1301894 C15 Capacitor, 2.2 µF, 16 V, Case A tantalum MCCTA225M016 FEC 1190115 D1 LED, yellow, 0603 LY Q971-H1K1-36-0-20-R18 Digi-Key 475-2557-1-ND D2 BAS516, high speed switching diodes BAS516 FEC 8734402 D3 BAS516, high speed switching diodes BAS516 FEC 8734402 D4 Diode ZENER, 4.7 V, 500 MW, SOD-80 FLZ4V7A Digi-Key FLZ4V7ACT-ND J2 Header, TIN, SIL, 32-way 3-826936-2 FEC 5217805 and FEC 1212164 (x7) J3 Header, TIN, SIL, 32-way 3-826936-2 FEC 5217805 and FEC 1212164 (x7) J4 Header, TIN, SIL, 32-way 3-826936-2 FEC 5217805 and FEC 1212164 (x7) J5 2-pin terminal block (5 mm pitch) CTB5000/2 FEC 151789 J6 120-way connector, 0.6 mm pitch FX8-120S-SV(21) FEC 1324660 J7 3-pin terminal block (5 mm pitch) CTB5000/3 FEC 151790 L1 Ferrite bead chip, series FB FB FBMH3225HM102NT FEC 1651731 L2 Ferrite bead chip, series FB FB FBMH3225HM102NT FEC 1651731 LK1 2-pin (0.1" pitch) header and shorting shunt M20-9990246 FEC 1022247 and FEC 150-411 LK2 3-pin SIL header and shorting link M20-9990345 and M7567-05 FEC 1022248 and FEC 150410 LK4 2-pin (0.1" pitch) header and shorting shunt M20-9990246 FEC 1022247 and FEC 150-411 LK6 2-pin (0.1" pitch) header and shorting shunt M20-9990246 FEC 1022247 and FEC 150-411 LK7 2-pin (0.1" pitch) header and shorting shunt M20-9990246 FEC 1022247 and FEC 150-411 R1 Resistor, 24 kΩ, 0805, 5 ppm PCF0805-13-24K-B-T1 FEC 1108901 R3 Resistor, 220 kΩ, 5%, 50 V, 0.063W, 0603 MC 0.063W 0603 5% 220K FEC 9331930 R4 Resistor, 1 kΩ, 5%, 50 V, 0.063W, 0603 MC 0.063W 0603 5% 1K FEC 9331697 R15 Resistor, HRC11 0805 18M RC0805JR-0718ML Yageo (Phycomp) FEC 9236422 R16 MULTICOMP, resistor, 0603 953 kΩ MC 0.063W 0603 1% 953K FEC 1171085 R18 RESISTOR, 0603, 100 kΩ, 1% MC 0.063W 0603 1% 100K FEC 9330402 R19 RESISTOR, 0603, 100 kΩ, 1% MC 0.063W 0603 1% 100K FEC 9330402 U1 Loop powered, 4 mA to 20 mA DAC AD5421CREZ AD5421CREZ U2 Depletion mode, N-channel MOSFET BSP129 FEC 1214279 U3 Digital isolator ADUM1401ARWZ ADuM1401ARWZ U5 Digital isolator ADuM1201ARZ ADuM1201ARZ U6 64K I2C serial EEPROM 24LC64-I/SN FEC 9758070
UG-250 Evaluation Board User Guide Rev. A | Page 12 of 12 NOTES ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. ©2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG09701-0-10/11(A)