B82614R2102A030 TDK | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

a~í~=pÜÉÉía~í~=pÜÉÉí Power line chokes Sine-wave chokes Series/Type: B82614 Date: July 2012 © EPCOS AG 2015. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. EPCOS AG is a TDK Group Company.

Please read Cautions and warnings and Important notes at the end of this document. Rated voltage 250 V AC Construction ■ Single choke ■ Air gapped rectangular ferrite core ■ Closed polycarbonate coil former (UL 94 V-0) ■ Without encapsulation ■ 4-section winding

Features

■ High resonance frequency due to 4-section winding ■ Low saturation effects due to gapped core ■ Suitable for wave soldering ■ Design complies with EN 60938-2 (VDE 0565-2) ■ Recyclable owing to omission of encapsulation and glue ■ RoHS-compatible

Applications

■ Switch-mode power supplies with current pump ■ Output filter in switch-mode applications ■ Reduction of harmonics and PFC Terminals ■ Base material CuNi18Zn20 ■ Layer composition Ni, Sn ■ Hot-dipped ■ Pins 0.7  0.7 (mm) ■ Lead spacing 12.5  15 (mm) Marking Manufacturer, rated inductance, rated current, ordering code, date of manufacture (WWYY) Delivery mode Blister tray in cardboard box B82614Power line chokes Sine-wave chokes

Please read Cautions and warnings and Important notes at the end of this document. Dimensional drawing and pin configuration IND0240-Z 15±0.2 12.5±0.2 32.5 max. 3+0.5 21 max. 31 max. 0.7 Tolerances to ISO 2768-C unless otherwise noted. Dimensions in mm. B82614Power line chokes Sine-wave chokes

Please read Cautions and warnings and Important notes at the end of this document. Technical data and measuring conditions Characteristics and ordering codes Rated voltage VR 250 V AC (50/60 Hz) Rated temperature TR +40 C Rated current IR Referred to 50 Hz and rated temperature Rated inductance LR Defined at zero DC current bias Measured with Agilent 4284A at 0.1 mA, +20 C Measuring frequency: L R 1 mH = 100 kHz LR > 1 mH = 10 kHz Inductance tolerance 30% at +20 C Inductance at rated current Measured at DC magnetic bias with I R with Agilent 4284A at 0.1 mA, +20 C, typical values Measuring frequency: L R 1 mH = 100 kHz LR > 1 mH = 10 kHz DC resistance Rtyp Measured at +20 C, typical values Solderability (lead free) Sn96.5Ag3.0Cu0.5: +(245 5) °C, (3 0.3) s Wetting of soldering area 95% (to IEC 60068-2-20, test Ta) Resistance to soldering heat (wave soldering) (to IEC 60068-2-20, test Tb) Climatic category 40/125/56 (to IEC 60068-1) Storage conditions (packaged) –25 °C … +40 °C, 75% RH Weight Approx. 30 g IR A LR mH L at IR, typ. mH Rtyp Ordering code 0.8 3.0 2.9 1.9 B82614R2801A030 1.0 2.0 1.9 1.3 B82614R2102A030 1.7 1.5 0.95 0.61 B82614R2172A030 2.0 1.0 0.75 0.43 B82614R2202A030 2.4 0.75 0.50 0.33 B82614R2242A030 2.7 0.5 0.42 0.23 B82614R2272A030 B82614Power line chokes Sine-wave chokes

Impedance |Z| versus frequency f measured at +20 °C, typical values Current derating Iop/IR versus ambient temperature TA Relative inductance Lop/LR versus relative current Iop/IR measured at +20 °C, typical values Ω ||Z 105 f Hz IND0866-L B82614 R2202A030 R2242A030 R2172A030 R2102A030 R2801A030 102 310 104 510 106 R2272A030 610 10 7 IND0868-C 020 opL LR RI opI % B82614 110 R2272A030 R2242A030 R2202A030 R2172A030 R2102A030 R2801A030 B82614Power line chokes Sine-wave chokes

Current-compensated ring core double chokes ■ Please note the recommendations in our Inducto rs data book (latest edition) and in the data sheets. – Particular attention should be paid to the derating curves given there. Derating must be applied in case the ambient temperature in the application exceeds the rated temperature of the component. – Ensure the operation temperature (which is the sum of the ambient temperature and the temperature rise caused by losses / self-heating) of the component in the application does not exceed the maximum value specified in the climatic category. – The soldering conditions should also be observed. Temperat ures quoted in relation to wave soldering refer to the pin, not the housing. ■ If the components are to be washed varnished it is necessary to check whether the washing varnish agent that is used has a negative effect on the wire insulation, any plastics that are used, or on glued joints. In particular, it is possible for washing varnish agent residues to have a negative effect in the long-term on wire insulation. Washing processes may damage the product due to the possible static or cyclic mechanical loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts, which might lead to reduced reliability or lifetime. ■ The following points must be observed if the components are potted in customer applications: – Many potting materials shrink as they harden. T hey therefore exert a pressure on the plastic housing or core. This pressure can have a delet erious effect on electr ical properties, and in extreme cases can damage the core or plastic housing mechanically. – It is necessary to check whether the potting material used attacks or destroys the wire insulation, plastics or glue. – The effect of the potting material can change the high-frequency behaviour of the components. ■ Ferrites are sensitive to direct impact. This c an cause the core material to flake, or lead to breakage of the core. ■ Even for customer-specific produc ts, conclusive validation of t he component in the circuit can only be carried out by the customer. Please read Cautions and warnings and Important notes at the end of this document.

Current-compensated ring core double chokes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application . These statements are based on our knowledge of typical requirements that are often placed on our produc ts in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons , it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other acti on taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous) . Useful information on this will be found in our Material Data Sheets on the Internet (www .epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time . The same is true of the corresponding product specifications. Please c heck therefore to what extent pr oduct descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products . Consequently, we cannot guarantee that all produc ts named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, FilterCap, Form Fit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineForm er, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks.