B65651W0000R030

B65659F0001X001 EPCOS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

PM/P/P Cores Halves/EP/TT/PR Cores Series/Type: P 18 x 11 The following products presented in this data sheet are being withdrawn. Ordering Code Substitute Product Date of WithdrawalDeadline Last Orders Last Shipments For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of our worldwide sales network are presented at www.epcos.com/sales.

Please read Cautions and warnings and Important notes at the end of this document. ■ To IEC 60133 ■ Delivery mode: sets Magnetic characteristics (per set) Approx. weight (per set) Gapped Ungapped with center hole without center hole Σl/A le Ae Amin Ve 0.6 25.9 1114 0.57 26.6 46.7 33.9 1242 mm mm mm2 mm2 mm3 m6 . 06 . 6g Material A L value nH s approx. mm µ e Ordering code 1) -D with center hole -T with threaded sleeve K1 40 ±3% 1.60 19 B65651+0040A001 M33 100 ±3% 0.60 48 B65651+0100A033 N48 160 ±3% 0.32 77 B65651+0160A048 250 ±3% 0.20 120 B65651+0250A048 315 ±3% 0.15 151 B65651+0315A048 400 ±3% 0.10 192 B65651+0400A048 500 ±3% 0.07 240 B65651+0500A048 630 ±5% 0.05 302 B65651D0630J048 Material A L value nH µe PV W/set Ordering code -D with center hole -W without center hole N48 2800 +30/–20% 1340 B65651D0000R048 N30 5900 +30/–20% 2680 B65651W0000R030 T38 12600 +40/–30% 5710 B65651W0000Y038 N87 3600 +30/–20% 1630 < 0.46 (200 mT, 100 kHz, 100 °C) B65651W0000R087 FPK0238-B s 2.4±0.15 0.35+0.1 7.2+0.4 ø3+0.1 3.9+0.5 14.9+0.5 0.511.8 _ 0.818.4 _10.6 0.2_ 0.3ø7.6 _ 1) Replace the + by the code letter ”D“ or ”T“ for the required version. B65651Core P 18 × 11

Please read Cautions and warnings and Important notes at the end of this document. Coil former Standard: to IEC 60133 Material: GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085: F max. operating temperature 155 °C), color code black Valox 420-SE0 ® [E45329 (M)], GE PLASTICS B V Winding: see Data Book 2007, chapter “Processing notes, 2.1” Insulating washer between core and coil former ■ For tolerance compensation and for insulation ■ Polycarbonate spring washer (UL 94 V-0, insulation class to IEC 60085: E 120 °C), 0.08 mm thick Aryphan F685, [E167358 (M)], natural color, LOFO HIGH TECH FILM GMBH Coil former Insulating washer Coil former Bestellnummer Sections A N mm2 lN mm AR value µΩ 1 16 35.6 87 B65652B0000T001 Insulating washer (reel packing, PU = 1 reel) B65652A5000X000 FPK0351-9 14.8 2+0.6 0.5 AN ø8.7 ø7.7+0.1 _0.2 _0.1 0.1_ (preliminary data) B65652Accessories P 18 × 11

Please read Cautions and warnings and Important notes at the end of this document. Mounting assembly for printed circuit boards ■ The set comprises a terminal carrier and a yoke ■ For snap-in connection Terminal carrier Material: GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085: F max. operating temperature 155 °C), color code gray Pocan B4235 ® [E245249 (M)], LANXESS AG Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 °C, 2 s Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 °C, 3.5 s Yoke Spring yoke, made of tinned nickel silver (0.3 mm), with ground terminal 4 solder terminals 8 solder terminals Complete mounting assembly (4 solder terminals) Ordering code: B65655B0009X000 Complete mounting assembly (8 solder terminals) Ordering code: B65655B0010X000 *) This recess must be on the side of the groundi ng pin to ensure that the yoke locks in position. a) Yoke b) Terminal carrier with 4 solder terminals c) Terminal carrier with 8 solder terminals FPK0295-U 20.1 max. 20.1 max. Ground 13.5 max.3.5 a b 20.7 max. ø1.3+0.1 2.54 8 1 Ground Hole arrangement View in mounting direction FPK0296-3 20.1 max. 20.1 max. Ground 13.5 max.3.5 a c 20.7 max. ø1.3+0.1 2.54 8 1 Ground Hole arrangement View in mounting direction B65655Accessories P 18 × 11

Please read Cautions and warnings and Important notes at the end of this document. Adjusting screw ■ Tube core with thread and core brake made of GFR polyterephthalate Pocan B3235® [E245249 (M)], LANXESS AG ab c Figure Tube core Ordering code ∅ × length (mm) Material Color code a2 . 6 2 × 3.6 K1 green B65659F0001X001 a2 . 6 2 × 3.6 N22 red B65659F0001X023 b2 . 7 5 × 4.4 N22 black B65659F0003X023 c2 . 8 2 × 4.4 N22 yellow B65659F0004X023 B65659Accessories P 18 × 11

Mechanical stress and mounting Ferrite cores have to meet mechanical requirements during assembling and for a growing number of applications. Since ferrites are ceramic materials one has to be aware of the special behavior under mechanical load. As valid for any ceramic material, ferrite cores are brittle and sensitive to any shock, fast changing or tensile load. Especially high cooling rates under ultrasonic cleaning and high static or cyclic loads can cause cracks or failure of the ferrite cores. For detailed information see Data Book 2007, chapter “General – Definitions, 8.1”. Effects of core combination on A L value Stresses in the core affect not only the mechanical but also the magnetic properties. It is apparent that the initial permeability is dependent on the stress state of the core. The higher the stresses are in the core, the lower is the value for the initia l permeability. Thus the embedding medium should have the greatest possible elasticity. For detailed information see Data Book 2007, chapter “General – Definitions, 8.2”. Heating up Ferrites can run hot during operation at higher flux densities and higher frequencies. NiZn-materials The magnetic properties of NiZn-materials can change irreversible in high magnetic fields. Processing notes – The start of the winding process should be soft. Else the flanges may be destroid. – To strong winding forces may blast the flanges or squeeze the tube that the cores can no more be mount. – To long soldering time at high temperature (>300 °C) may effect coplanarity or pin arrangement. – Not following the processing notes for soldering of the J-leg terminals may cause solderability problems at the transformer because of pollution with Sn oxyd of the tin bath or burned insulation of the wire. For detailed information see Data Book 2007, chapter “Processing notes, 2.2”. – The dimensions of the hole arrangement have fixed values and should be understood as a recommendation for drilling the printed circuit board. For dimensioning the pins, the group of holes can only be seen under certain conditions, as they fit into the given hole arrangement. To avoid problems when mounting the transformer, the manufacturing tolerances for positioning the customers’ drilling process must be considered by increasing the hole diameter.

The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application . These statements are based on our knowledge of typical requirements that are often placed on our prod ucts in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual servic e life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must th erefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy cert ain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as “hazardous”) . Useful information on th is will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time . The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products . Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Produc ts and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, EPCOS-JONES, Baoke, Alu-X, CeraDiode, CSSP, MLSC, PhaseCap, PhaseMod, SIFI, SIFERRIT, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, UltraCap, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks.