DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 15
Technical content
Aluminum electrolytic capacitors Capacitors with screw terminals Series/Type: B44020, B44030 Date: October 2015 © EPCOS AG 2015. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. EPCOS AG is a TDK Group Company.
Accessories for capacitors with mounting stud on capacitor base Insulating washer made of hostalen Capacitor diameter Thread size Dimensional drawing Diameter d mm Ordering code 35.7 mm M8 d1 0.5 = 35 d2 0.5 = 24 d3 ±0.3 = 16.5 d4 ±0.2 = 9 B44020B0006B035 51.6 mm M12 d1 0.5 = 51 d2 0.5 = 31 d3 ±0.3 = 21.5 d4 ±0.2 = 13 B44020B0006B051 64.2 mm M12 d1 0.5 = 63.5 d2 0.5 = 43.5 d3 ±0.3 = 21.5 d4 ±0.2 = 13 B44020B0006B064 76.9 mm M12 d1 0.5 = 76 d2 0.5 = 56 d3 ±0.3 = 21.5 d4 ±0.2 = 13 B44020B0006B076 90 mm M12 d1 0.5 = 89 d2 0.5 = 69 d3 ±0.3 = 21.5 d4 ±0.2 = 13 B44020B0006B090 Screw terminals Accessories B44020 Screw terminals Accessories Page 2 of 15Please read Cautions and warnings and Important notes at the end of this document.
Thread size Dimensional drawing Ordering code ≤ 40 mm M81) width across flats 17 mm B44020J0006B008 > 40 mm M122) width across flats 19 mm B44020J0006B012 > 40 mm M122) width across flats 19 mm B44020J0007B012 1) Maximum torque M8: 2.0 Nm for mounting tread length≥ 7 mm 2) Maximum torque M12: 7.0 Nm for mounting tread length≥ 13 mm; 5.0 Nm for mounting tread length≥ 10 mm B44020 Screw terminals Accessories Page 3 of 15Please read Cautions and warnings and Important notes at the end of this document.
Insulated mounting with washer and cap nut: Mounting stud has the same potential as the negative terminal. Attention must be paid on any relevant regulations (e.g. VDE, BSA or UL). B44020 Screw terminals Accessories Page 4 of 15Please read Cautions and warnings and Important notes at the end of this document.
Ring clips are primarily used for upright mounting of screw terminal and photoflash capacitors. The ring clips are corrosion protected and are RoHS-compatible. It is recommended to insert an additional insulating strip between capacitor and ring clip to avoid any risk of damage due to edges from the clip. The strip is included in delivery. For ordering code, see the following table. Attention must be paid to any relevant regulations (e.g. VDE, BSA or UL). dN h1 mm Ring clip version Ordering code with insulating strip 35.7 15 10 B44030J0036B000 (insulating strip length: 230 mm) 51.6 22 15 B44030J0051B000 (insulating strip length: 325 mm) B44030 Screw terminals Accessories Page 5 of 15Please read Cautions and warnings and Important notes at the end of this document.
Ring clip version Ordering code with insulating strip 64.3 29 19 B44030J0064B000 (insulating strip length: 420 mm) 76.9 29 19 B44030J0075B000 (insulating strip length: 495 mm) 90 29 19 B44030J0090B000 (insulating strip length: 585 mm) B44030 Screw terminals Accessories Page 6 of 15Please read Cautions and warnings and Important notes at the end of this document.
Screw terminal capacitors without threaded stud and with a diameter ≥ 64.3 mm can also be mounted with ring clamps. Clamp mounting offers the following advantages: Optimum heat transfer between capacitor base and board due to pressure contact High vibration resistance Electrically insulated material Dimensional drawing 1) Length of screw depends on application. 2) The screws have to be tightened uniformly and crosswise until the fixing part rests flatly on the board. 3) Tubular rivets included in delivery package. General hints for mounting: If required, the four fixation parts can be cut out from the common carrier ring and mounted separately. Dimensions and ordering codes Capacitor diameter dN d1 ±0.2 mm b mm Ordering code 65 mm 87 104 B44030A0165B000 75 mm 99 116 B44030A0175B000 90 mm 112 130 B44030A0190B000 Screws are not included in the delivery package. B44030 Screw terminals Accessories Page 7 of 15Please read Cautions and warnings and Important notes at the end of this document.
Mounting set (ring clamps) Dimensions and ordering codes Protects the capacitor against tilt and the terminals from mechanical stress Fits for different capacitor length Electrically insulated clamping material Capacitor diameter dN ∅ min Ordering code 75 mm 84 mm B44030A0375B000 90 mm 96.5 mm B44030A0390B000 Dimensional drawing B44030 Screw terminals Accessories Page 8 of 15Please read Cautions and warnings and Important notes at the end of this document.
The electrolytes used by EPCOS have been optimized both with a view to the intended application and with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide (DMAC). Furthermore, some of the high-voltage electrolytes used by EPCOS are self-extinguishing. As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce operating electrolytes. However, in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no alternative materials are currently known. However, the amount of dangerous materials used in our products is limited to an absolute minimum. Materials and chemicals used in EPCOS aluminum electrolytic capacitors are continuously adapted in compliance with the EPCOS Corporate Environmental Policy and the latest EU regulations and guidelines such as RoHS, REACH/SVHC, GADSL, and ELV. MDS (Material Data Sheets) are available on the EPCOS website for all types listed in the data book. MDS for customer specific capacitors are available upon request. MSDS (Material Safety Data Sheets) are available for all of our electrolytes upon request. Nevertheless, the following rules should be observed when handling aluminum electrolytic capacitors: No electrolyte should come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected areas immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid inhaling electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water. B44020, B44030 Screw terminals Accessories Page 9 of 15Please read Cautions and warnings and Important notes at the end of this document.
The table below summarize the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of chapter "General technical information". Topic Safety information Reference chapter "General technical information" Polarity Make sure that polar capacitors are connected with the right polarity. "Basic construction of aluminum electrolytic capacitors" Reverse voltage Voltages of opposite polarity should be prevented by connecting a diode. 3.1.6 "Reverse voltage" Mounting position of screw- terminal capacitors Screw terminal capacitors must not be mounted with terminals facing down unless otherwise specified. 11.1. "Mounting positions of capacitors with screw terminals" Robustness of terminals The following maximum tightening torques must not be exceeded when connecting screw terminals: M5: 2.5 Nm M6: 4.0 Nm 11.3 "Mounting torques" Mounting of single-ended capacitors The internal structure of single-ended capacitors might be damaged if excessive force is applied to the lead wires. Avoid any compressive, tensile or flexural stress. Do not move the capacitor after soldering to PC board. Do not pick up the PC board by the soldered capacitor. Do not insert the capacitor on the PC board with a hole space different to the lead space specified. 11.4 "Mounting considerations for single-ended capacitors" Soldering Do not exceed the specified time or temperature limits during soldering. 11.5 "Soldering" Soldering, cleaning agents Do not allow halogenated hydrocarbons to come into contact with aluminum electrolytic capacitors. 11.6 "Cleaning agents" Upper category temperature Do not exceed the upper category temperature. 7.2 "Maximum permissible operating temperature" Passive flammability Avoid external energy, e.g. fire. 8.1 "Passive flammability" B44020, B44030 Screw terminals Accessories Page 10 of 15Please read Cautions and warnings and Important notes at the end of this document.
Topic Safety information Reference chapter "General technical information" Active flammability Avoid overload of the capacitors. 8.2 "Active flammability" Maintenance Make periodic inspections of the capacitors. Before the inspection, make sure that the power supply is turned off and carefully discharge the electricity of the capacitors. Do not apply excessive mechanical stress to the capacitor terminals when mounting. "Maintenance" Storage Do not store capacitors at high temperatures or high humidity. Capacitors should be stored at +5 to +35 °C and a relative humidity of ≤ 75%. 7.3 "Shelf life and storage conditions" Reference chapter "Capacitors with screw terminals" Breakdown strength of insulating sleeves Do not damage the insulating sleeve, especially when ring clips are used for mounting. "Screw terminals accessories" Display of ordering codes for EPCOS products The ordering code for one and the same product can be represented differently in data sheets, data books, other publications and the website of EPCOS, or in order-related documents such as shipping notes, order confirmations and product labels. The varying representations of the ordering codes are due to different processes employed and do not affect the specifications of the respective products. Detailed information can be found on the Internet under www.epcos.com/orderingcodes. B44020, B44030 Screw terminals Accessories Page 11 of 15Please read Cautions and warnings and Important notes at the end of this document.
C Capacitance Kapazität CR Rated capacitance Nennkapazität CS Series capacitance Serienkapazität CS,T Series capacitance at temperature T Serienkapazität bei Temperatur T Cf Capacitance at frequency f Kapazität bei Frequenz f d Case diameter, nominal dimension Gehäusedurchmesser, Nennmaß dmax Maximum case diameter Maximaler Gehäusedurchmesser ESL Self-inductance Eigeninduktivität ESR Equivalent series resistance Ersatzserienwiderstand ESRf Equivalent series resistance at frequency f Ersatzserienwiderstand bei Frequenz f ESRT Equivalent series resistance at temperature T Ersatzserienwiderstand bei Temperatur T f Frequency Frequenz I Current Strom IAC Alternating current (ripple current) Wechselstrom IAC,RMS Root-mean-square value of alternating current Wechselstrom, Effektivwert IAC,f Ripple current at frequency f Wechselstrom bei Frequenz f IAC,max Maximum permissible ripple current Maximal zulässiger Wechselstrom IAC,R Rated ripple current Nennwechselstrom Ileak Leakage current Reststrom Ileak,op Operating leakage current Betriebsreststrom l Case length, nominal dimension Gehäuselänge, Nennmaß lmax Maximum case length (without terminals and mounting stud) Maximale Gehäuselänge (ohne Anschlüsse und Gewindebolzen) R Resistance Widerstand Rins Insulation resistance Isolationswiderstand Rsymm Balancing resistance Symmetrierwiderstand T Temperature Temperatur ΔT Temperature difference Temperaturdifferenz TA Ambient temperature Umgebungstemperatur TC Case temperature Gehäusetemperatur TB Capacitor base temperature Temperatur des Gehäusebodens t Time Zeit Δt Period Zeitraum tb Service life (operating hours) Brauchbarkeitsdauer (Betriebszeit) B44020, B44030 Screw terminals Accessories Page 12 of 15Please read Cautions and warnings and Important notes at the end of this document.
VF Forming voltage Formierspannung Vop Operating voltage Betriebsspannung VR Rated voltage, DC voltage Nennspannung, Gleichspannung VS Surge voltage Spitzenspannung XC Capacitive reactance Kapazitiver Blindwiderstand XL Inductive reactance Induktiver Blindwiderstand Z Impedance Scheinwiderstand ZT Impedance at temperature T Scheinwiderstand bei Temperatur T tan δ Dissipation factor Verlustfaktor λ Failure rate Ausfallrate ε0 Absolute permittivity Elektrische Feldkonstante εr Relative permittivity Dielektrizitätszahl ω Angular velocity; 2 π f Kreisfrequenz; 2 π f Note All dimensions are given in mm. B44020, B44030 Screw terminals Accessories Page 13 of 15Please read Cautions and warnings and Important notes at the end of this document.
The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application . These statements are based on our knowledge of typical re- quirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application . As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incum- bent on the customer to check and decide whether an EPCOS product with the properties de- scribed in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified . In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Ma- terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de- tailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time . The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products . Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the fore- going for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver- sion of the "General Terms of Delivery for Products and Services in the Electrical In- dustry" published by the German Electrical and Electronics Industry Association (ZVEI). Important notes Page 14 of 15
- The trade names EPCOS, Alu-X, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PQSine, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, TFAP, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Important notes Page 15 of 15