DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 18
Technical content
Aluminum electrolytic capacitors Capacitors with screw terminals Series/Type: B43700, B43720 Date: December 2014 © EPCOS AG 2014. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited.
Long-life grade capacitors
Applications
Uninterruptible power supplies Professional power supplies
Features
High voltage up to 600 V DC High reliability and high ripple current capability All-welded constructions ensures reliable electrical contact PAPR terminals available (Protection Against Polarity Reversal) Version available with an optimized base cooling design (heat sink mounting) and featuring up to 2 times the ripple current capability RoHS-compatible Construction Charge-discharge proof, polar Aluminum case with insulating sleeve Poles with screw terminal connections Mounting with ring clips, clamps or threaded stud The bases of types with threaded stud are not insulated B43700 B43720 Capacitors with screw terminals B43700, B43720 High voltage 85 °C Page 2 of 18Please read Cautions and warnings and Important notes at the end of this document.
1) Refer to chapter "General technical information, 5 Useful life" on how to interpret useful life. Specifications and characteristics in brief Rated voltage VR Surge voltage VS 550 ... 600 V DC 1.10 VR Rated capacitance CR Capacitance tolerance 680 ... 6800 µF ±20% M Dissipation factor tan δ (20 °C, 120 Hz) ≤ 0.20 Leakage current Ileak (20 °C, 5 min) Self-inductance ESL d ≥ 64.3 mm: approx. 20 nH Useful life1) 550 V 600 V Requirements: 85 °C; VR; IAC,R > 8000 h > 6000 h ΔC/C ≤ 15% of initial value tan δ ≤ 1.75 times initial specified limit Ileak ≤ initial specified limit Voltage endurance test Post test requirements: 85 °C; VR 2000 h ΔC/C ≤ 10% of initial value tan δ ≤ 1.3 times initial specified limit Ileak ≤ initial specified limit Vibration resistance test To IEC 60068-2-6, test Fc: Frequency range 10 ... 55 Hz, displacement amplitude 0.75 mm, acceleration max. 10 g, duration 3 × 2 h. Capacitor mounted by its body which is rigidly clamped to the work surface. Characteristics at low temperature Max. impedance ratio at 100 Hz Z -25°C / Z 20°C 3 Z -40°C / Z 20°C 10 IEC climatic category To IEC 60068-1: 40/085/56 ( 40 °C/+85 °C/56 days damp heat test) Detail specification Sectional specification Similar to CECC 30301-803, CECC 30301-807 IEC 60384-4 Ripple current capability Due to the ripple current capability of the contact elements, the following current upper limits must not be exceeded: Capacitor diameter 51.6 mm 64.3 mm 76.9 mm 90 mm IAC,max 45 A 60 A 67 A 80 A B43700, B43720 High voltage 85 °C Page 3 of 18Please read Cautions and warnings and Important notes at the end of this document.
For types with threaded stud the base is not insulated. Also refer to the mounting instructions in chapter "Capacitors with screw terminals Accessories". Screw terminals with UNF threads are available upon request. Dimensions and weights (Standard capacitors, without heat sink) Ter- minal Dimensions (mm) with insulating sleeve Approx. weight (g)d l ±1 l1 ±1 l2 +0/ 1 d1 d2 max. a +0.2/ 0.4 51.6 +0.5/ 1 51.6 +0.5/ 1 51.6 +0.5/ 1 96.7 105.7 118.2 103.2 112.2 124.7 M12 M12 M12 10.2 10.2 10.2 22.2 22.2 22.2 250 280 320 64.3 +0.5/ 1 64.3 +0.5/ 1 64.3 +0.5/ 1 64.3 +0.5/ 1 96.7 105.7 118.2 130.7 103.2 112.2 124.7 137.2 M12 M12 M12 M12 13.2 13.2 13.2 13.2 28.5 28.5 28.5 28.5 400 440 510 600 76.9 +0.5/ 1 76.9 +0.5/ 1 76.9 +0.5/ 1 76.9 +0.5/ 1 76.9 +0.5/ 1 76.9 +0.5/ 1 76.9 +0.5/ 1 76.9 +0.5/ 1 96.7 105.7 118.2 130.7 143.2 168.7 190.7 220.7 102.5 111.5 124.0 136.5 149.0 174.5 196.5 226.5 M12 M12 M12 M12 M12 M12 M12 M12 17.7 17.7 17.7 17.7 17.7 17.7 17.7 17.7 31.7 31.7 31.7 31.7 31.7 31.7 31.7 31.7 570 620 700 800 840 1000 1150 1300 90.0 +0.5/ 1.5 90.0 +0.5/ 1.5 90.0 +0.5/ 1.5 90.0 +0.5/ 1.5 144.5 170.0 191.0 221.0 149.8 175.3 196.3 226.3 M12 M12 M12 M12 17.7 17.7 17.7 17.7 31.7 31.7 31.7 31.7 1200 1400 1650 1900 B43700, B43720 High voltage 85 °C Page 4 of 18Please read Cautions and warnings and Important notes at the end of this document.
diameter d (mm) length l (mm) Packing units (pcs.) 64.3 all 25 76.9 ≤ 168.7 16 > 168.7 12 90.0 all 9 For ecological reasons the packing is pure cardboard. B43700, B43720 High voltage 85 °C Page 5 of 18Please read Cautions and warnings and Important notes at the end of this document.
With our PAPR terminal style (Protection Against Polarity Reversal) we offer an optional mechanical feature in addition to the visual polarity marking on the cover disk and the sleeve, which prevents from mounting in reverse polarity. The non-circular shape of the terminals and their arrangement perpendicular to each other enables the user to definitely prevent wrong mounting with respect to polarity (Poka Yoke). Dimensional drawing of PAPR terminal configuration Dimensions for PAPR terminal style (mm) Standard design #050 For heat sink mounting #057 64.3 M5 13 15 28.5 9.5 7.3 76.9 M6 13 15 31.7 12.0 9.7 90.0 M6 13 15 31.7 12.0 9.7 All other dimensions of the capacitor such as diameter d, case length l and overall length l1 are identical with those of standard capacitors of this series. Please refer to the tables "Dimensions and weights" (standard types) and "Dimensions and weights for heat sink mounting" (special designs). For heat sink mounting Please refer to chapter "General technical information, 5.2.2 Base cooling with heat sink". This version is available only for capacitors without threaded stud and for diameters ≥ 64.3 mm. Regarding ripple current and useful life, please refer to chapter "General technical information, 5 Useful life". B43700, B43720 High voltage 85 °C Page 6 of 18Please read Cautions and warnings and Important notes at the end of this document.
Dimensions and weights for heat sink mounting: Terminal Dimensions (mm) with insulating sleeve Approx. weight gd l ±1 l1 ±0.35 d2 max. a +0.2/ 0.4 64.3 +0.5/ 1 64.3 +0.5/ 1 96.7 105.7 102.3 111.3 13.2 13.2 28.5 28.5 400 440 76.9 +0.5/ 1 76.9 +0.5/ 1 76.9 +0.5/ 1 96.7 105.7 118.2 101.6 110.6 123.1 17.7 17.7 17.7 31.7 31.7 31.7 570 620 700 Dimensions for other sizes are available upon request. Ordering codes: Design Identification in third block of ordering code Remark For heat sink mounting M007 For capacitors without threaded stud PAPR terminal style M050 PAPR terminal style and heat sink mounting M057 For capacitors without threaded stud B43700, B43720 High voltage 85 °C Page 7 of 18Please read Cautions and warnings and Important notes at the end of this document.
The following items are included in the delivery package, but are not fastened to the capacitors: Thread Toothed washers Screws/nuts Maximum torque For terminals M5 A 5.1 DIN 6797 DIN 7985 / ISO 7045-M5 × 10-5.6-Z 2.5 Nm thread depth t ≥ 8 mm M6 A 6.4 DIN 6797 DIN 7985 / ISO 7045-M6 × 12-5.6-Z 4.0 Nm thread depth t ≥ 9.5 mm For mounting M12 J 12.5 DIN 6797 Hex nut BM 12 DIN 439 10 Nm The following items must be ordered separately. For details, refer to chapter "Capacitors with screw terminals Accessories". Item Type Ring clips B44030 Clamps for capacitors with d ≥ 64.3 mm B44030 Insulating parts B44020 B43700, B43720 High voltage 85 °C Page 8 of 18Please read Cautions and warnings and Important notes at the end of this document.
Overview of available types VR (V DC) 550 600 Case dimensions d × l (mm) CR (µF) 680 51.6 × 96.7 820 51.6 × 96.7 1000 51.6 × 105.7 1200 51.6 × 118.2 64.3 × 105.7 1500 64.3 × 96.7 64.3 × 118.2 76.9 × 96.7 1800 64.3 × 118.2 76.9 × 96.7 64.3 × 130.7 76.9 × 105.7 2200 64.3 × 130.7 76.9 × 105.7 76.9 × 118.2 2700 76.9 × 130.7 76.9 × 130.7 3300 76.9 × 143.2 76.9 × 168.7 3900 76.9 × 190.7 90.0 × 144.5 4700 76.9 × 220.7 90.0 × 170.0 5600 90.0 × 191.0 6800 90.0 × 221.0 The capacitance and voltage ratings listed above are available in different cases upon request. Other voltage and capacitance ratings are also available upon request. B43700, B43720 High voltage 85 °C Page 9 of 18Please read Cautions and warnings and Important notes at the end of this document.
Technical data and ordering codes CR 100 Hz 20 °C µF Case dimensions d × l mm ESRtyp 100 Hz 20 °C mΩ ESRtyp 300 Hz 60 °C mΩ Zmax 10 kHz 20 °C mΩ IAC,max 100 Hz 60 °C A IAC,R 100 Hz 85 °C A Ordering code (composition see below) Composition of ordering code * = Mounting style ## = Design 0 = for capacitors with ring clip/clamp mounting 2 = for capacitors with threaded stud 00 = for standard capacitors 07 = for heat sink mounting (only without threaded stud) 50 = for terminals with PAPR style 57 = for terminals with PAPR style and heat sink mounting (only without threaded stud) VR = 550 V DC 680 51.6 × 96.7 130 36 200 8.05 3.87 B437*0A7687M0## 820 51.6 × 96.7 110 30 170 9.56 4.40 B437*0A7827M0## 1000 51.6 × 105.7 90 24 140 10.9 5.05 B437*0A7108M0## 1200 51.6 × 118.2 75 20 120 12.4 5.74 B437*0A7128M0## 1500 64.3 × 96.7 60 17 90 14.6 6.74 B437*0A7158M0## 1800 64.3 × 118.2 50 14 75 16.5 7.60 B437*0A7188M0## 1800 76.9 × 96.7 50 14 75 17.4 8.02 B437*0B7188M0## 2200 64.3 × 130.7 40 12 65 18.9 8.73 B437*0A7228M0## 2200 76.9 × 105.7 40 12 65 19.7 9.09 B437*0B7228M0## VR = 600 V DC 1200 64.3 × 105.7 80 22 120 12.0 6.63 B437*0B8128M0## 1500 64.3 × 118.2 65 17 95 13.9 7.71 B437*0C8158M0## 1500 76.9 × 96.7 65 17 95 14.7 8.15 B437*0D8158M0## 1800 64.3 × 130.7 55 15 80 15.8 8.76 B437*0C8188M0## 1800 76.9 × 105.7 55 15 80 16.5 9.13 B437*0D8188M0## 2200 76.9 × 118.2 45 12 65 18.8 10.3 B437*0C8228M0## 2700 76.9 × 130.7 36 10 55 21.5 11.8 B437*0B8278M0## B43700, B43720 High voltage 85 °C Page 10 of 18Please read Cautions and warnings and Important notes at the end of this document.
1) Refer to chapter "General technical information, 5 Useful life" on how to interpret useful life. Useful life1) For useful life calculations, please use our web-based "AlCap Useful Life Calculation Tool", which can be found on the Internet under the following link http://www.epcos.com/designtools/alu_useful_life/Useful_life.swf. The AlCap Useful Life Calculation Tool provides calculations of useful life as well as additional data for selected capacitor types under operating conditions defined by the user. Frequency characteristics of ESR Typical behavior Impedance Z versus frequency f Typical behavior at 20 °C B43700, B43720 High voltage 85 °C Page 11 of 18Please read Cautions and warnings and Important notes at the end of this document.
The electrolytes used by EPCOS have been optimized both with a view to the intended application and with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide (DMAC). Furthermore, some of the high-voltage electrolytes used by EPCOS are self-extinguishing. As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce operating electrolytes. However, in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no alternative materials are currently known. However, the amount of dangerous materials used in our products is limited to an absolute minimum. Materials and chemicals used in EPCOS aluminum electrolytic capacitors are continuously adapted in compliance with the EPCOS Corporate Environmental Policy and the latest EU regulations and guidelines such as RoHS, REACH/SVHC, GADSL, and ELV. MDS (Material Data Sheets) are available on the EPCOS website for all types listed in the data book. MDS for customer specific capacitors are available upon request. MSDS (Material Safety Data Sheets) are available for all of our electrolytes upon request. Nevertheless, the following rules should be observed when handling aluminum electrolytic capacitors: No electrolyte should come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected areas immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid inhaling electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water. B43700, B43720 High voltage 85 °C Page 12 of 18Please read Cautions and warnings and Important notes at the end of this document.
The table below summarizes the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of chapter "General technical information". Topic Safety information Reference chapter "General technical information" Polarity Make sure that polar capacitors are connected with the right polarity. "Basic construction of aluminum electrolytic capacitors" Reverse voltage Voltages of opposite polarity should be prevented by connecting a diode. 3.1.6 "Reverse voltage" Mounting position of screw- terminal capacitors Screw terminal capacitors must not be mounted with terminals facing down unless otherwise specified. 11.1. "Mounting positions of capacitors with screw terminals" Robustness of terminals The following maximum tightening torques must not be exceeded when connecting screw terminals: M5: 2.5 Nm M6: 4.0 Nm 11.3 "Mounting torques" Mounting of single-ended capacitors The internal structure of single-ended capacitors might be damaged if excessive force is applied to the lead wires. Avoid any compressive, tensile or flexural stress. Do not move the capacitor after soldering to PC board. Do not pick up the PC board by the soldered capacitor. Do not insert the capacitor on the PC board with a hole space different to the lead space specified. 11.4 "Mounting considerations for single-ended capacitors" Soldering Do not exceed the specified time or temperature limits during soldering. 11.5 "Soldering" Soldering, cleaning agents Do not allow halogenated hydrocarbons to come into contact with aluminum electrolytic capacitors. 11.6 "Cleaning agents" Upper category temperature Do not exceed the upper category temperature. 7.2 "Maximum permissible operating temperature" Passive flammability Avoid external energy, e.g. fire. 8.1 "Passive flammability" B43700, B43720 High voltage 85 °C Page 13 of 18Please read Cautions and warnings and Important notes at the end of this document.
Topic Safety information Reference chapter "General technical information" Active flammability Avoid overload of the capacitors. 8.2 "Active flammability" Maintenance Make periodic inspections of the capacitors. Before the inspection, make sure that the power supply is turned off and carefully discharge the electricity of the capacitors. Do not apply excessive mechanical stress to the capacitor terminals when mounting. "Maintenance" Storage Do not store capacitors at high temperatures or high humidity. Capacitors should be stored at +5 to +35 °C and a relative humidity of ≤ 75%. 7.3 "Shelf life and storage conditions" Reference chapter "Capacitors with screw terminals" Breakdown strength of insulating sleeves Do not damage the insulating sleeve, especially when ring clips are used for mounting. "Screw terminals accessories" Display of ordering codes for EPCOS products The ordering code for one and the same product can be represented differently in data sheets, data books, other publications and the website of EPCOS, or in order-related documents such as shipping notes, order confirmations and product labels. The varying representations of the ordering codes are due to different processes employed and do not affect the specifications of the respective products. Detailed information can be found on the Internet under www.epcos.com/orderingcodes B43700, B43720 High voltage 85 °C Page 14 of 18Please read Cautions and warnings and Important notes at the end of this document.
C Capacitance Kapazität CR Rated capacitance Nennkapazität CS Series capacitance Serienkapazität CS,T Series capacitance at temperature T Serienkapazität bei Temperatur T Cf Capacitance at frequency f Kapazität bei Frequenz f d Case diameter, nominal dimension Gehäusedurchmesser, Nennmaß dmax Maximum case diameter Maximaler Gehäusedurchmesser ESL Self-inductance Eigeninduktivität ESR Equivalent series resistance Ersatzserienwiderstand ESRf Equivalent series resistance at frequency f Ersatzserienwiderstand bei Frequenz f ESRT Equivalent series resistance at temperature T Ersatzserienwiderstand bei Temperatur T f Frequency Frequenz I Current Strom IAC Alternating current (ripple current) Wechselstrom IAC,RMS Root-mean-square value of alternating current Wechselstrom, Effektivwert IAC,f Ripple current at frequency f Wechselstrom bei Frequenz f IAC,max Maximum permissible ripple current Maximal zulässiger Wechselstrom IAC,R Rated ripple current Nennwechselstrom Ileak Leakage current Reststrom Ileak,op Operating leakage current Betriebsreststrom l Case length, nominal dimension Gehäuselänge, Nennmaß lmax Maximum case length (without terminals and mounting stud) Maximale Gehäuselänge (ohne Anschlüsse und Gewindebolzen) R Resistance Widerstand Rins Insulation resistance Isolationswiderstand Rsymm Balancing resistance Symmetrierwiderstand T Temperature Temperatur ΔT Temperature difference Temperaturdifferenz TA Ambient temperature Umgebungstemperatur TC Case temperature Gehäusetemperatur TB Capacitor base temperature Temperatur des Gehäusebodens t Time Zeit Δt Period Zeitraum tb Service life (operating hours) Brauchbarkeitsdauer (Betriebszeit) B43700, B43720 High voltage 85 °C Page 15 of 18Please read Cautions and warnings and Important notes at the end of this document.
VF Forming voltage Formierspannung Vop Operating voltage Betriebsspannung VR Rated voltage, DC voltage Nennspannung, Gleichspannung VS Surge voltage Spitzenspannung XC Capacitive reactance Kapazitiver Blindwiderstand XL Inductive reactance Induktiver Blindwiderstand Z Impedance Scheinwiderstand ZT Impedance at temperature T Scheinwiderstand bei Temperatur T tan δ Dissipation factor Verlustfaktor λ Failure rate Ausfallrate ε0 Absolute permittivity Elektrische Feldkonstante εr Relative permittivity Dielektrizitätszahl ω Angular velocity; 2 π f Kreisfrequenz; 2 π f Note All dimensions are given in mm. B43700, B43720 High voltage 85 °C Page 16 of 18Please read Cautions and warnings and Important notes at the end of this document.
The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application . These statements are based on our knowledge of typical re- quirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application . As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incum- bent on the customer to check and decide whether an EPCOS product with the properties de- scribed in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified . In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Ma- terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de- tailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time . The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products . Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the fore- going for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver- sion of the "General Terms of Delivery for Products and Services in the Electrical In- dustry" published by the German Electrical and Electronics Industry Association (ZVEI). Important notes Page 17 of 18
- The trade names EPCOS, Alu-X, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PQSine, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, TFAP, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks.vvv Important notes Page 18 of 18