B43081A2476M000

B43081A1226M000 EPCOS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 15

Technical content

Aluminum electrolytic capacitors Alu-X product lines Single-ended capacitors Series/Type: B43081 Date: August 2008 © EPCOS AG 2008. Reproduction, publication and dissemination of this publication and the infor- mation contained therein without EPCOS’ prior express consent is prohibited.

Single-ended capacitors B43081 High ripple current – 105 °C 2 08/08 Please read Cautions and warnings and Important notes at the end of this document. Long-life grade capacitors for professional applications

Applications

■ Electronic ballast applications

Features

■ RoHS-compatible ■ Very high ripple current ■ High reliability ■ Load life of 3000 h at 105 °C Construction ■ Radial leads ■ Aluminum case, fully insulated ■ Charge-discharge proof ■ Minus pole marking on the insulating sleeve ■ Case with safety vent from diameter 8 mm Delivery mode ■ Bulk ■ Taped, Ammo pack ■ Cut ■ Kinked Single-ended capacitors B43081 High ripple current – 105 °C

Single-ended capacitors B43081 High ripple current – 105 °C 3 08/08 Please read Cautions and warnings and Important notes at the end of this document. Specifications and characteristics in brief Rated voltage VR 160 ... 400 V DC Operating temperature range –25 °C … +105 °C Rated capacitance CR (20 °C, 120 Hz) 0.1 … 100 µF Capacitance tolerance ±20% M Load life (105 °C, VR, IAC,R) 3000 h Requirements: ∆C/C ≤ ±20% of initial value tan δ≤ 2 times initial specified limit Ileak ≤ initial specified limit Leakage current Ileak (20 °C, after 5 minutes) Dissipation factor (max.) (20 °C, 120 Hz) tan δ ≤ 0.12 Low temperature stability (impedance ratio) (120 Hz) ≤ 7 Shelf life After storage for 1000 h at 105 °C, the capacitors shall meet the require- ment of load life test after reforming process. After test: VR to be applied for 30 minutes, 24 to 48 hours before measurement. Frequency multiplier for rated ripple current

50 Hz 120 Hz 300 Hz 1 kHz 10 kHz 100 kHz

2.1 1.8 1.4 1.0 Ileak 0.02 µA CR ⎛⎞⋅≤ Z2 5 ° C–()

Single-ended capacitors B43081 High ripple current – 105 °C 4 08/08 Please read Cautions and warnings and Important notes at the end of this document. Dimensional drawing Safety vent for diameter ≥ 8 mm. Case dimensions d × l mm d max × Imax mm a mm b mm KAL1080-C-E a d marking 15 min. 5 min. øb Minus pole Safety vent l

Single-ended capacitors B43081 High ripple current – 105 °C 5 08/08 Please read Cautions and warnings and Important notes at the end of this document. Overview of available types VR (V DC) 160 200 250 350 400 Case dimensions d × l (mm) CR (µF) 2.2 8 × 15 3.3 8 × 15 8 × 20 4.7 8 × 11.5 10 × 16 10 × 20 6.8 10 × 16 10 × 16 10 × 20 12.5 × 20 10 10 × 16 10 × 16 10 × 20 10 × 20 12.5 × 20 15 10 × 20 10 × 16 16 × 25 22 10 × 20 10 × 20 10 × 20 12.5 × 20 12.5 × 20 12.5 × 25 16 × 25 33 10 × 20 12.5 × 20 12.5 × 20 12.5 × 25 16 × 20 16 × 25 16 × 31.5 47 12.5 × 20 12.5 × 25 12.5 × 20 12.5 × 25 16 × 25 16 × 25 16 × 35.5 18 × 25 68 12.5 × 25 12.5 × 25 16 × 20 16 × 25 18 × 35.5 18 × 25 100 16 × 25 16 × 25 18 × 20 18 × 25

Single-ended capacitors B43081 High ripple current – 105 °C 6 08/08 Please read Cautions and warnings and Important notes at the end of this document. * = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm 006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm 008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm Technical data and ordering codes VR V DC CR 120 Hz 20 °C µF Case dimensions d × l mm IAC,R 100 kHz 105 °C mA Ordering code (composition see below) 160 22 10 × 20 500 B43081A1226M* 33 10 × 20 500 B43081A1336M* 47 12.5 × 20 600 B43081A1476M* 47 12.5 × 25 670 B43081B1476M* 68 12.5 × 25 750 B43081A1686M* 100 16 × 25 1100 B43081A1107M* 200 4.7 8 × 11.5 158 B43081A2475M* 6.8 10 × 16 230 B43081A2685M* 10 10 × 16 310 B43081A2106M* 15 10 × 20 400 B43081A2156M* 22 10 × 20 500 B43081A2226M* 33 12.5 × 20 600 B43081A2336M* 47 12.5 × 20 600 B43081A2476M* 68 12.5 × 25 750 B43081A2686M* 68 16 × 20 750 B43081B2686M* 100 16 × 25 1100 B43081A2107M* 100 18 × 20 1100 B43081B2107M* 250 1.0 8 × 11.5 18 B43081F2105M* 4.7 10 × 16 200 B43081F2475M* 6.8 10 × 16 240 B43081F2685M* 10 10 × 16 300 B43081F2106M* 15 10 × 16 380 B43081F2156M* 22 10 × 20 500 B43081F2226M* 22 12.5 × 20 600 B43081G2226M* 33 12.5 × 20 600 B43081F2336M* 33 12.5 × 25 670 B43081G2336M* 47 12.5 × 25 700 B43081F2476M* 47 16 × 25 780 B43081G2476M* 68 16 × 25 1000 B43081F2686M* 68 18 × 35.5 1200 B43081G2686M* 100 18 × 25 1200 B43081F2107M* 350 10 10 × 20 250 B43081A4106M* 22 12.5 × 20 350 B43081A4226M* 33 16 × 20 500 B43081A4336M* 47 16 × 25 650 B43081A4476M* 68 18 × 25 800 B43081A4686M***

Single-ended capacitors B43081 High ripple current – 105 °C 7 08/08 Please read Cautions and warnings and Important notes at the end of this document. * = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm 006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm 008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm Technical data and ordering codes VR V DC CR 120 Hz 20 °C µF Case dimensions d × l mm I AC,R 100 kHz 105 °C mA Ordering code (composition see below) 400 1.0 6.3 × 11.5 18 B43081A9105M* 2.2 8 × 15 108 B43081A9225M* 3.3 8 × 15 108 B43081A9335M* 3.3 8 × 20 121 B43081B9335M* 4.7 10 × 20 180 B43081A9475M* 6.8 10 × 20 220 B43081A9685M* 6.8 12.5 × 20 240 B43081B9685M* 10 10 × 20 250 B43081A9106M* 10 12.5 × 20 270 B43081B9106M* 15 16 × 25 400 B43081A9156M* 22 12.5 × 25 400 B43081A9226M* 22 16 × 25 500 B43081B9226M* 33 16 × 25 600 B43081A9336M* 33 16 × 31.5 670 B43081B9336M* 47 16 × 35.5 750 B43081A9476M* 47 18 × 25 750 B43081B9476M***

Single-ended capacitors B43081 Taping, packing and lead configurations 8 08/08 Please read Cautions and warnings and Important notes at the end of this document. Taping, packing and lead configurations of single-ended capacitors Single-ended capacitors are available taped in Ammo pack from diameter 4 to 10 mm as follows: Lead spacing 2.0 mm (∅ d = 4 ... 5 mm) Last 3 digits of ordering code: 016 Dimensions in mm ∅ dF H W W 0 W1 W2 PP 0 P1 l1 t ∆hD 0 Adhesive tape Base tape F B H ød P W t KAL1138-D-E 1 max. View B W0 W2 h∆h ∆ Single-ended capacitors B43081 Taping, packing and lead configurations

Single-ended capacitors B43081 Taping, packing and lead configurations 9 08/08 Please read Cautions and warnings and Important notes at the end of this document. Last 3 digits of ordering code: 007 Lead spacing 3.5 mm (∅ d = 8 mm) Last 3 digits of ordering code: 006 Dimensions in mm ∅ dF H H 0 WW 0 W1 W2 PP 0 P1 l1 t ∆hD 0 Dimensions in mm ∅ dF H W W 0 W1 W2 PP 0 P1 l1 t ∆hD 0 Adhesive tape Base tape F B H ød P W t KAL1074-3-E 1 max. View B W0 W2 h∆h ∆ Adhesive tape Base tape F B H ød P W t KAL1138-D-E 1 max. View B W0 W2 h∆h ∆

Single-ended capacitors B43081 Taping, packing and lead configurations 10 08/08 Please read Cautions and warnings and Important notes at the end of this document. Lead spacing 5.0 mm (∅ d = 4 ... 8 mm) Last 3 digits of ordering code: 008 Lead spacing 5.0 mm (∅ d = 10 mm) Last 3 digits of ordering code: 008 Taping is available up to dimensions d × l = 10 × 20 mm. For ∅ 12.5, 16 and 18 mm taping is not available. Dimensions in mm ∅ dF H H 0 WW 0 W1 W2 PP 0 P1 L1 t ∆hD 0 Tolerance +0.6 –0.2 ±0.75 ±0.5 +1.0 –0.5 +1.0 –0.2 max. ±0.2 Adhesive tape Base tape F B H ød P W KAL1075-B-E t 1 max. View B W2W0 h∆ h∆ Adhesive tape Base tape F B H ød P W KAL1076-J-Et 1 max. View B W0 W2 h∆ h∆

Single-ended capacitors B43081 Taping, packing and lead configurations 11 08/08 Please read Cautions and warnings and Important notes at the end of this document. Kinked or cut leads Single-ended capacitors are available with kinked or cut leads. Other lead configurations also avail- able on request. Kinked leads Last 3 digits of ordering code: 001 Case size d × l (mm) a (mm) Case size d × l (mm) a (mm) 4 × 7 1.5 12.5 × 16 5.0 5 × 7 2.0 12.5 × 20 5.0 5 × 11 2.0 12.5 × 25 5.0 6.3 × 15 2.5 12.5 × 40 5.0 8 × 7 3.5 16 × 20 7.5 8 × 11.5 3.5 16 × 25 7.5 8 × 15 3.5 16 × 31.5 7.5 8 × 20 3.5 16 × 35.5 7.5 10 × 12.5 5.0 16 × 40 7.5 10 × 16 5.0 18 × 20 7.5 10 × 20 5.0 18 × 25 7.5 10 × 25 5.0 18 × 31.5 7.5 10 × 31.5 5.0 18 × 35.5 7.5 18 × 40 7.5 ød 3.2±0.1 KAL1137-5 1.2±0.1 2.1±0.1l 4.5±0.5 ød KAL1084-A a l

Single-ended capacitors B43081 Taping, packing and lead configurations 12 08/08 Please read Cautions and warnings and Important notes at the end of this document. Cut leads Last 3 digits of ordering code: 002 Case size d × l (mm) a (mm) Case size d × l (mm) a (mm) 4 × 7 1.5 12.5 × 16 5.0 5 × 7 2.0 12.5 × 20 5.0 5 × 11 2.0 12.5 × 25 5.0 6.3 × 15 2.5 12.5 × 40 5.0 8 × 7 3.5 16 × 20 7.5 8 × 11.5 3.5 16 × 25 7.5 8 × 15 3.5 16 × 31.5 7.5 8 × 20 5.0 16 × 35.5 7.5 10 × 12.5 5.0 16 × 40 7.5 10 × 16 5.0 18 × 20 7.5 10 × 20 5.0 18 × 25 7.5 10 × 25 5.0 18 × 31.5 7.5 10 × 31.5 5.0 18 × 35.5 7.5 18 × 40 7.5 ød KAL1086-R a 4.5±0.5 l

Please read Cautions and warnings and Important notes at the end of this document. General Also see “Important notes” on page 15. 1 Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors must not be used in AC applications, where the polarity may be reversed in the circuits or is unknown.

2 The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage,

as this will result in a rapid increase of the leakage current and may damage the capacitor. It is recommended to operate the capacitor at 70–80% of its rated voltage to optimize its serv- ice life. 3 The ripple current applied to the capacitor must be within the permitted range. An excessive ripple current leads to impaired electrical properties and may damage the capacitor. Note that the sum of the peak values of the ripple voltage and the DC operating voltage must not ex- ceed the rated DC voltage. 4 Capacitors must be used within their permitted range of operating temperature. Operation at room temperature optimizes their service life. 5 Capacitors with case diameter ≥8 mm are equipped with a safety vent. In capacitors fitted with a lead or soldering lug, the safety vent is usually located at the base of the case. It needs sufficient space around it to operate optimally. The following dimensions are recommended: for case diameter d = 8 to 16 mm, more than 2 mm; for d =18 to 35 mm, more than 3 mm; and for d = 42 mm or more, more than 5 mm. 6 Capacitors should not be mounted with the safety vent face down on the board. Do not locate any wire or copper trace near the safety vent. Do not reverse the voltage, as this may result in excess pressure and the leakage of electrolyte. 7 Gas is released through the safety vent when t he pressure inside the capacitor is too high. A gaseous liquid around the safety vent does not indicate a leakage of electrolyte.

8 The capacitor should be stored under conditions of normal temperature and in a non-acid,

non-alkali environment of normal humidity. Exposure to high temperatures, for example un- der direct sunlight, will reduce its operating life. If the capacitor is stored in an environment containing acids or alkalis, the solderability of the leads may be affected.

9 The leakage current of an alumi num electrolytic capacitor ma y increase after a long period

of storage. After such storage, the capacitor must be aged by applying the rated operating voltage for 6–8 hours before use.

10 Manual soldering:

a Soldering must be performed within the specified conditions. Bit temperature: 350 °C; application time of soldering iron: 3 seconds. b Ensure that the soldering iron does not touch any part of the capacitor body. Cautions and warnings

Please read Cautions and warnings and Important notes at the end of this document. 11 Do not apply excessive force to the leads and te rminals. Do not move the capacitor after sol- dering it onto the PC board and do not carry the PC board by gripping the capacitor. Observe the following rules to prevent undue stress to the capacitor: a Do not tilt or bend the capacitor after soldering. b Ensure that the terminal spacing matc hes the corresponding hole spacing on the PC board. 12 The aluminum case is not insulated from the cathode. Do not place a conductor under the aluminum capacitors on the PC board as this may cause a short circuit. The case and top of capacitors used in switched mode power supplie s have a high-voltage-resistant heat shrink sleeve to ensure safe usage. 13 The leads of capacitors with a case diam eter exceeding 14 mm cannot be used for fixing.

The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application . These statements are based on our knowledge of typical requirements that are often placed on our produc ts in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons , it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous) . Useful information on this will be found in our Material Data Sheets on the Internet (www .epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to im prove our products. Consequently, the products described in this publication may change from time to time . The same is true of the corresponding product specifications. Please c heck therefore to what extent pr oduct descriptions an d specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will al ways be available. The aforementioned does not apply in case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, Cera Diode, CSSP, CTVS, DSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SI P5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks.