B41002A2226M001

B41002 EPCOS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 16

Technical content

Aluminum electrolytic capacitors Alu-X product lines Single-ended capacitors Series/Type: B41002 Date: August 2008 © EPCOS AG 2008. Reproduction, publication and dissemination of this publication and the infor- mation contained therein without EPCOS’ prior express consent is prohibited.

Single-ended capacitors B41002 Compact – 85 °C 2 08/08 Please read Cautions and warnings and Important notes at the end of this document. General-purpose grade capacitors

Applications

■ Car radio, EDP systems

Features

■ RoHS-compatible ■ Ultra compact – height up to 7 mm ■ Suitable to replace low cost tantalum capacitors ■ Load life of 1000 h at 85 °C Construction ■ Radial leads ■ Aluminum case, fully insulated ■ Charge-discharge proof ■ Minus pole marking on the insulating sleeve ■ Case with safety vent from diameter 8 mm Delivery mode ■ Bulk ■ Taped, Ammo pack ■ Cut ■ Kinked Single-ended capacitors B41002 Compact – 85 °C

Single-ended capacitors B41002 Compact – 85 °C 3 08/08 Please read Cautions and warnings and Important notes at the end of this document. Specifications and characteristics in brief Rated voltage VR 6.3 … 63 V DC Operating temperature range –40 °C … +85 °C Rated capacitance CR (20 °C, 120 Hz) 0.1 … 330 µF Capacitance tolerance ±20% M Load life (85 °C, VR, IAC,R) 1000 h Requirements: ∆C/C ≤ ±20% of initial value tan δ≤ 2 times initial specified value Ileak ≤ initial specified limit Dissipation factor tan δ (20 °C, 120 Hz) For capacitance higher than 1000 µF add 0.02 for every increase of 1000 µF VR (V DC) 6.3 10 16 25 35 50 63 Leakage current Ileak (20 °C, after 5 minutes) Low temperature stability (impedance ratio) (120 Hz) 75 4 Shelf life After storage for 500 h at 85 °C, the capacitors shall meet the requirement of load life test after reforming process. After test: VR to be applied for 30 minutes, 24 to 48 hours before measurement. Frequency multiplier for rated ripple current

50 Hz 120 Hz 1 kHz ≥10 kHz

Temperature multiplier for rated ripple current 1.50 1.27 1.00 Ileak 0.01 µA CR ⎛⎞ or 3 µA, whichever is greater⋅≤ Z4 0 ° C–()

Single-ended capacitors B41002 Compact – 85 °C 4 08/08 Please read Cautions and warnings and Important notes at the end of this document. Dimensional drawing Safety vent for diameter ≥ 8 mm. Case dimensions d × l mm dmax × Imax mm a mm b mm Overview of available types VR ( V D C ) 6 . 3 1 01 62 5 Case dimensions d × l (mm) CR (µF) 3.3 4 × 7 4.7 4 × 74 × 7 6.8 4 × 74 × 7 10 4 × 74 × 7 15 4 × 74 × 75 × 7 22 4 × 74 × 74 × 75 × 7 33 4 × 74 × 75 × 7 6.3 × 7 47 5 × 75 × 7 6.3 × 7 6.3 × 7 68 5 × 7 6.3 × 7 6.3 × 78 × 7 100 6.3 × 7 6.3 × 78 × 78 × 7 220 8 × 78 × 78 × 7 330 8 × 7 KAL1080-C-E a d marking 15 min. 5 min. øb Minus pole Safety vent l

Single-ended capacitors B41002 Compact – 85 °C 5 08/08 Please read Cautions and warnings and Important notes at the end of this document. Overview of available types VR (V DC) 35 50 63 Case dimensions d × l (mm) CR (µF) 0.1 4 × 74 × 7 0.15 4 × 74 × 7 0.22 4 × 74 × 7 0.33 4 × 74 × 7 0.47 4 × 74 × 7 0.68 4 × 74 × 7 1.0 4 × 74 × 74 × 7 1.5 4 × 74 × 74 × 7 2.2 4 × 74 × 74 × 7 3.3 4 × 74 × 75 × 7 4.7 4 × 74 × 75 × 7 6.8 4 × 75 × 7 6.3 × 7 10 5 × 75 × 7 6.3 × 7 15 5 × 7 6.3 × 7 22 6.3 × 78 × 7 33 6.3 × 78 × 7 47 8 × 7

Single-ended capacitors B41002 Compact – 85 °C 6 08/08 Please read Cautions and warnings and Important notes at the end of this document. * = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm 007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm 006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm 008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm Technical data and ordering codes VR V DC CR 120 Hz 20 °C µF Case dimensions d × l mm I AC,R 120 Hz 85 °C mA Ordering code (composition see below) 6.3 22 4 × 7 35 B41002A2226M* 33 4 × 7 40 B41002A2336M* 47 5 × 7 50 B41002A2476M* 68 5 × 7 60 B41002A2686M* 100 6.3 × 7 80 B41002A2107M* 220 8 × 7 130 B41002A2227M* 330 8 × 7 190 B41002A2337M* 10 15 4 × 7 28 B41002A3156M* 22 4 × 7 35 B41002A3226M* 33 4 × 7 45 B41002A3336M* 47 5 × 7 60 B41002A3476M* 68 6.3 × 7 75 B41002A3686M* 100 6.3 × 7 90 B41002A3107M* 220 8 × 7 160 B41002A3227M* 16 4.7 4 × 7 20 B41002A4475M* 6.8 4 × 7 25 B41002A4685M* 10 4 × 7 30 B41002A4106M* 15 4 × 7 35 B41002A4156M* 22 4 × 7 40 B41002A4226M* 33 5 × 7 55 B41002A4336M* 47 6.3 × 7 68 B41002A4476M* 68 6.3 × 7 80 B41002A4686M* 100 8 × 7 100 B41002A4107M* 220 8 × 7 160 B41002A4227M* 25 3.3 4 × 7 15 B41002A5335M* 4.7 4 × 7 20 B41002A5475M* 6.8 4 × 7 25 B41002A5685M* 10 4 × 7 29 B41002A5106M* 15 5 × 7 35 B41002A5156M* 22 5 × 7 49 B41002A5226M* 33 6.3 × 7 60 B41002A5336M* 47 6.3 × 7 80 B41002A5476M* 68 8 × 7 100 B41002A5686M* 100 8 × 7 125 B41002A5107M***

Single-ended capacitors B41002 Compact – 85 °C 7 08/08 Please read Cautions and warnings and Important notes at the end of this document. * = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm 007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm 006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm 008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm Technical data and ordering codes VR V DC CR 120 Hz 20 °C µF Case dimensions d × l mm I AC,R 120 Hz 85 °C mA Ordering code (composition see below) 35 1.0 4 × 7 8.0 B41002A7105M* 1.5 4 × 7 10 B41002A7155M* 2.2 4 × 7 13 B41002A7225M* 3.3 4 × 7 16 B41002A7335M* 4.7 4 × 7 22 B41002A7475M* 6.8 4 × 7 26 B41002A7685M* 10 5 × 7 31 B41002A7106M* 15 5 × 7 40 B41002A7156M* 22 6.3 × 7 52 B41002A7226M* 33 6.3 × 7 70 B41002A7336M* 47 8 × 7 95 B41002A7476M* 50 0.1 4 × 7 1.0 B41002A6104M* 0.15 4 × 7 1.5 B41002A6154M* 0.22 4 × 7 2.3 B41002A6224M* 0.33 4 × 7 3.5 B41002A6334M* 0.47 4 × 7 5.0 B41002A6474M* 0.68 4 × 7 8.0 B41002A6684M* 1.0 4 × 7 10 B41002A6105M* 1.5 4 × 7 13 B41002A6155M* 2.2 4 × 7 16 B41002A6225M* 3.3 4 × 7 22 B41002A6335M* 4.7 4 × 7 26 B41002A6475M* 6.8 5 × 7 30 B41002A6685M* 10 5 × 7 38 B41002A6106M* 15 6.3 × 7 44 B41002A6156M* 22 8 × 7 60 B41002A6226M* 33 8 × 7 90 B41002A6336M*

Single-ended capacitors B41002 Compact – 85 °C 8 08/08 Please read Cautions and warnings and Important notes at the end of this document. * = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk 002 = for cut leads, bulk 016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm 007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm 006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm 008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm Technical data and ordering codes VR V DC CR 120 Hz 20 °C µF Case dimensions d × l mm I AC,R 120 Hz 85 °C mA Ordering code (composition see below) 63 0.1 4 × 7 1.0 B41002A8104M* 0.15 4 × 7 1.5 B41002A8154M* 0.22 4 × 7 2.3 B41002A8224M* 0.33 4 × 7 3.5 B41002A8334M* 0.47 4 × 7 5.0 B41002A8474M* 0.68 4 × 7 8.0 B41002A8684M* 1.0 4 × 7 10 B41002A8105M* 1.5 4 × 7 13 B41002A8155M* 2.2 4 × 7 16 B41002A8225M* 3.3 5 × 7 23 B41002A8335M* 4.7 5 × 7 30 B41002A8475M* 6.8 6.3 × 7 35 B41002A8685M* 10 6.3 × 7 40 B41002A8106M*

Single-ended capacitors B41002 Taping, packing and lead configurations 9 08/08 Please read Cautions and warnings and Important notes at the end of this document. Taping, packing and lead configurations of single-ended capacitors Single-ended capacitors are available taped in Ammo pack from diameter 4 to 10 mm as follows: Lead spacing 2.0 mm (∅ d = 4 ... 5 mm) Last 3 digits of ordering code: 016 Dimensions in mm ∅ dF H W W 0 W1 W2 PP 0 P1 l1 t ∆hD 0 Adhesive tape Base tape F B H ød P W t KAL1138-D-E 1 max. View B W0 W2 h∆h ∆ Single-ended capacitors B41002 Taping, packing and lead configurations

Single-ended capacitors B41002 Taping, packing and lead configurations 10 08/08 Please read Cautions and warnings and Important notes at the end of this document. Last 3 digits of ordering code: 007 Lead spacing 3.5 mm (∅ d = 8 mm) Last 3 digits of ordering code: 006 Dimensions in mm ∅ dF H H 0 WW 0 W1 W2 PP 0 P1 l1 t ∆hD 0 Dimensions in mm ∅ dF H W W 0 W1 W2 PP 0 P1 l1 t ∆hD 0 Adhesive tape Base tape F B H ød P W t KAL1074-3-E 1 max. View B W0 W2 h∆h ∆ Adhesive tape Base tape F B H ød P W t KAL1138-D-E 1 max. View B W0 W2 h∆h ∆

Single-ended capacitors B41002 Taping, packing and lead configurations 11 08/08 Please read Cautions and warnings and Important notes at the end of this document. Lead spacing 5.0 mm (∅ d = 4 ... 8 mm) Last 3 digits of ordering code: 008 Lead spacing 5.0 mm (∅ d = 10 mm) Last 3 digits of ordering code: 008 Taping is available up to dimensions d × l = 10 × 20 mm. For ∅ 12.5, 16 and 18 mm taping is not available. Dimensions in mm ∅ dF H H 0 WW 0 W1 W2 PP 0 P1 L1 t ∆hD 0 Tolerance +0.6 –0.2 ±0.75 ±0.5 +1.0 –0.5 +1.0 –0.2 max. ±0.2 Adhesive tape Base tape F B H ød P W KAL1075-B-E t 1 max. View B W2W0 h∆ h∆ Adhesive tape Base tape F B H ød P W KAL1076-J-Et 1 max. View B W0 W2 h∆ h∆

Single-ended capacitors B41002 Taping, packing and lead configurations 12 08/08 Please read Cautions and warnings and Important notes at the end of this document. Kinked or cut leads Single-ended capacitors are available with kinked or cut leads. Other lead configurations also avail- able on request. Kinked leads Last 3 digits of ordering code: 001 Case size d × l (mm) a (mm) Case size d × l (mm) a (mm) 4 × 7 1.5 12.5 × 16 5.0 5 × 7 2.0 12.5 × 20 5.0 5 × 11 2.0 12.5 × 25 5.0 6.3 × 15 2.5 12.5 × 40 5.0 8 × 7 3.5 16 × 20 7.5 8 × 11.5 3.5 16 × 25 7.5 8 × 15 3.5 16 × 31.5 7.5 8 × 20 3.5 16 × 35.5 7.5 10 × 12.5 5.0 16 × 40 7.5 10 × 16 5.0 18 × 20 7.5 10 × 20 5.0 18 × 25 7.5 10 × 25 5.0 18 × 31.5 7.5 10 × 31.5 5.0 18 × 35.5 7.5 18 × 40 7.5 ød 3.2±0.1 KAL1137-5 1.2±0.1 2.1±0.1l 4.5±0.5 ød KAL1084-A a l

Single-ended capacitors B41002 Taping, packing and lead configurations 13 08/08 Please read Cautions and warnings and Important notes at the end of this document. Cut leads Last 3 digits of ordering code: 002 Case size d × l (mm) a (mm) Case size d × l (mm) a (mm) 4 × 7 1.5 12.5 × 16 5.0 5 × 7 2.0 12.5 × 20 5.0 5 × 11 2.0 12.5 × 25 5.0 6.3 × 15 2.5 12.5 × 40 5.0 8 × 7 3.5 16 × 20 7.5 8 × 11.5 3.5 16 × 25 7.5 8 × 15 3.5 16 × 31.5 7.5 8 × 20 5.0 16 × 35.5 7.5 10 × 12.5 5.0 16 × 40 7.5 10 × 16 5.0 18 × 20 7.5 10 × 20 5.0 18 × 25 7.5 10 × 25 5.0 18 × 31.5 7.5 10 × 31.5 5.0 18 × 35.5 7.5 18 × 40 7.5 ød KAL1086-R a 4.5±0.5 l

Please read Cautions and warnings and Important notes at the end of this document. General Also see “Important notes” on page 16. 1 Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors must not be used in AC applications, where the polarity may be reversed in the circuits or is unknown.

2 The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage,

as this will result in a rapid increase of the leakage current and may damage the capacitor. It is recommended to operate the capacitor at 70–80% of its rated voltage to optimize its serv- ice life. 3 The ripple current applied to the capacitor must be within the permitted range. An excessive ripple current leads to impaired electrical properties and may damage the capacitor. Note that the sum of the peak values of the ripple voltage and the DC operating voltage must not ex- ceed the rated DC voltage. 4 Capacitors must be used within their permitted range of operating temperature. Operation at room temperature optimizes their service life. 5 Capacitors with case diameter ≥8 mm are equipped with a safety vent. In capacitors fitted with a lead or soldering lug, the safety vent is usually located at the base of the case. It needs sufficient space around it to operate optimally. The following dimensions are recommended: for case diameter d = 8 to 16 mm, more than 2 mm; for d =18 to 35 mm, more than 3 mm; and for d = 42 mm or more, more than 5 mm. 6 Capacitors should not be mounted with the safety vent face down on the board. Do not locate any wire or copper trace near the safety vent. Do not reverse the voltage, as this may result in excess pressure and the leakage of electrolyte. 7 Gas is released through the safety vent when t he pressure inside the capacitor is too high. A gaseous liquid around the safety vent does not indicate a leakage of electrolyte.

8 The capacitor should be stored under conditions of normal temperature and in a non-acid,

non-alkali environment of normal humidity. Exposure to high temperatures, for example un- der direct sunlight, will reduce its operating life. If the capacitor is stored in an environment containing acids or alkalis, the solderability of the leads may be affected.

9 The leakage current of an alumi num electrolytic capacitor ma y increase after a long period

of storage. After such storage, the capacitor must be aged by applying the rated operating voltage for 6–8 hours before use.

10 Manual soldering:

a Soldering must be performed within the specified conditions. Bit temperature: 350 °C; application time of soldering iron: 3 seconds. b Ensure that the soldering iron does not touch any part of the capacitor body. Cautions and warnings

Please read Cautions and warnings and Important notes at the end of this document. 11 Do not apply excessive force to the leads and te rminals. Do not move the capacitor after sol- dering it onto the PC board and do not carry the PC board by gripping the capacitor. Observe the following rules to prevent undue stress to the capacitor: a Do not tilt or bend the capacitor after soldering. b Ensure that the terminal spacing matc hes the corresponding hole spacing on the PC board. 12 The aluminum case is not insulated from the cathode. Do not place a conductor under the aluminum capacitors on the PC board as this may cause a short circuit. The case and top of capacitors used in switched mode power supplie s have a high-voltage-resistant heat shrink sleeve to ensure safe usage. 13 The leads of capacitors with a case diam eter exceeding 14 mm cannot be used for fixing.

The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application . These statements are based on our knowledge of typical requirements that are often placed on our produc ts in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons , it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous) . Useful information on this will be found in our Material Data Sheets on the Internet (www .epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to im prove our products. Consequently, the products described in this publication may change from time to time . The same is true of the corresponding product specifications. Please c heck therefore to what extent pr oduct descriptions an d specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will al ways be available. The aforementioned does not apply in case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, Cera Diode, CSSP, CTVS, DSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SI P5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks.