B39431B3757U310 EPCOS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

2 Mar 20, 2003

434,42 MHzLow-loss Filter Data Sheet

Features

■ RF low-loss filter for remote control receivers ■ Package for Surface M ounted Technology (SMT ) ■ Balanced and unbalanced operation possible ■ Passivation layer: Protec Terminals ■ Ni, gold plated Pin configuration

1 Input Ground

2 Input

5 Output

6 Output Ground

4,8 Case - Ground 3,7 to be grounded ElectrostacticSensitiveD evice (ESD ) Type Ordering code Marking and package according to Packing according to B3757 B39431-B3757-U310 C61157-A7-A56 F61074-V8070-Z000 Maximum ratings Operable temperature range TA –45/+120 ˚C Storage temperature rangeTstg –45/+120 ˚C DC voltage VDC 6V Source power PS 10 dBm source impedance 50 Ω typ. dimensions in mm, approx. weight 0,1 g Ceramic package QCC8C

3 Mar 20, 2003

434,42 MHzLow-loss Filter Data Sheet Characteristics Reference temperature: TA = –40 ... +95˚C Terminating source impedance: ZS = 50Ω and matching network Terminating load impedance: ZL = 50Ω and matching network 2) Impedance for passband matching bases on an ideal, perfect matching of the SAW filter to source- and to load impedance (here 50 Ohm). After the SAW filter is removed and input imped- ance into the input matching / output matching network is calculated. The conjugate complex value of these characteristic impedances are the input and output imped- ances for flat passband. For more details, we refer to EPCOS application note #4. min. typ. max. Center frequency fC — 434,42 — MHz (center frequency between 3 dB points) Minimum insertion attenuation α min (including losses in matching network) 434,26 ... 434,58 MHz — 2,0 3,0 dB Pass band (relative toα min) 434,26 ... 434,58 MHz — 0,5 2,0 dB 434,24 ... 434,60 MHz — 0,7 3,0 dB 434,20 ... 434,64 MHz — 1,0 6,0 dB Pass bandwidth α rel≤ 3 dB 0,64 0,70 0,76 MHz Relative attenuation(relative toα min) α rel 10,00 ... 414,50 MHz 55 62 — dB 414,50 ... 425,00 MHz 48 55 — dB 425,00 ... 432,22 MHz 31 35 — dB 432,22 ... 432,62 MHz 39 44 — dB 432,62 ... 433,60 MHz 8 11 — dB 435,42 ... 442,50 MHz 10 14 — dB 442,50 ... 550,00 MHz 36 44 — dB 550,00 ... 700,00 MHz 55 60 — dB 700,00 ... 805,00 MHz 40 45 — dB 805,00 ...1000,00 MHz 60 70 — dB Impedance for pass band matching Input: ZIN = R IN ||C IN — 310 || 2,2 — Ω || pF Output:ZOUT = R OUT ||C OUT — 310 || 2,2 — Ω || pF

4 Mar 20, 2003

434,42 MHzLow-loss Filter Data Sheet Matching network to 50Ω (element values depend on pcb layout and equivalent circuit) Ls1 = 39 nH Ls2 = 39 nH Minimising the crosstalk For a good ultimate rejection a low crosstalk is necessary. Low crosstalk can be realised with a good RF layout. The major crosstalk mechanism is caused by the “ground-loop” problem. Grounding loops are created if input-and output transducer GND are connected on the top-side of the PCB and fed to the system grounding plane by a common via hole. To avoid the common ground path, the ground pin of the input- and output transducer are fed to the system ground plane (bottom PCB plane) by their own via hole. The transducers’ grounding pins should be isolated from the upper grounding plane. A common GND inductivity of 0.5nH degrades the ultimate rejection (crosstalk) by 20dB. The optimised PCB layout, including matching network for transformation to 50 Ohm, is shown here. In this PCB layout the grounding loops are minimised to realise good ultimate rejection. Optimised PCB layout for SAW filters in QCC8C package, pinning 2,5 (top side, scale 1:1) The bottom side is a copper plane (system ground area). The input and output grounding pins are isolated and connected to the common ground by separated via holes. For good contact of the upper grounding area with the lower side it is necessary to place enough via holes.

5 Mar 20, 2003

434,42 MHzLow-loss Filter Data Sheet Frequency response Frequency response(wideband)

6 Mar 20, 2003

434,42 MHzLow-loss Filter Data Sheet Frequency response(ultimate rejection) Published by EPCOS AG Surface Acoustic Wave Components Division, SAW CE AE PD P.O. Box 80 17 09, D-81617 München  EPCOS AG 2003. All Rights Reserved. Reproduction, publication and dissemination of this bro- chure and the information contained therein without EPCOS’ prior express consent is prohibited. The information contained in this brochure describes the type of component and shall not be con- sidered as guaranteed characteristics. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices.