B0303XT-1W RSG | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Specifications subject to change without notice. B_(X)T-1W A/0-2007 Page 1 of 2 B_(X)T-1W Series 1W,FIXED INPUT, ISOLATED & UNREGULATED single OUTPUT, SMD DC-DC CONVERTER multi-country patent protection RoHS PRODUCT PROGRAM Input Output Voltage (VDC) Current (mA) Part Number Nominal Range Voltage (VDC) Max Min Efficiency (%, Typ.) UL CE B0303(X)T-1W 3.3 303 30 73 B0305(X)T-1W 3.3 3.0-3.6 5 200 20 74 B0503(X)T-1W 3.3 303 30 72 B0505(X)T-1W 5 200 20 77 UL，CE B0509(X)T-1W 9 111 12 76 UL，CE B0512(X)T-1W 12 84 9 79 UL，CE B0515(X)T-1W 5 4.5-5.5 15 67 7 78 UL，CE B1205(X)T-1W 5 200 20 69 UL，CE B1209(X)T-1W 9 111 12 73 UL，CE B1212(X)T-1W 12 84 9 73 UL，CE B1215(X)T-1W 12 10.8-13.2 15 67 7 74 UL，CE B2403(X)T-1W 3.3 300 30 69 B2405(X)T-1W 5 200 20 70 B2409(X)T-1W 9 110 11 72 B2412(X)T-1W 12 83 8 75 B2415(X)T-1W 15 67 7 76 B2424(X)T-1W 24 21.6-26.4 24 42 4 77 Note :1.the B_XT-1W series have no 3,6,7 pin. For example B0505XT-1W. 2. B_XT-1W :UL-60950-1 pending. OUTPUT SPECIFICATIONS Item Test Conditions Min Typ. Max Units Output power 1 W For Vin change of 1%(3.3V tt ) ±1.5 Line regulation For Vin change of 1%(Others) ±1.2 10% to 100% load (3.3V output) 15 20 10% to 100% load (5V output) 12.8 15 10% to 100% load (9V output) 8.3 15 10% to 100% load (12V output) 6.8 15 Load regulation 10% to 100% load (15V output) 6.3 15 Output voltage accuracy See tolerance envelope graph Temperature drift 100% full load 0.03 %/°C Output ripple &Noise* 20MHz Bandwidth 50 75 mVp-p Full load, nominal input(5/12V) 100 KHz

FEATURES

Temperature Range: -40°C~+85°C No External Component Required RoHS Compliance

APPLICATIONS

The B_(X)T-1W Series are specially designed for applications where a group of polar power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is fixed (voltage variation ≤ ±10%); 2) Where isolation is necessary between input and output (isolation voltage ≤1000VDC); 3) Where the regulation of the output voltage and the output ripple noise are not demanding. Such as: purely digital circuits, ordinary low frequency analog circuits, and IGBT power device driving circuits. MODEL SELECTION B0505(X )T-1W Product Series Input Voltage Output Voltage Package Style Rated Power Switching frequency Full load, nominal input(24V) 500 *test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. Note: 1.All specifications measured at T A=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2.See below recommended circuits for more details. RSG ELECTRONIC COMPONENTS RSG Electronic Components GmbH ■ Sprendlinger Landstr. 115 ■ D-63069 Offenbach/Germany Tel. +49 69 984047-0 ■ Fax +49 69 984047-77 ■ info@rsg-electronic.de ■ www.rsg-electronic.de Änderungen vorbehalten / subject to change without notice

Specifications subject to change without notice. B_(X)T-1W A/0-2007 Page 2 of 2 COMMON SPECIFICATION APPLICATION NOTE Item Test Conditions Min Typ Max Units Storage humidity 95 % Operating temperature -40 85 Storage temperature -55 125 Temp. rise at full load 15 25 Lead temperature 1.5mm from case for 10 seconds 260 Cooling Free air convection Isolation voltage Tested for 1 minute and 1mA ma x 1000 VDC Isolation resistance Test at 500VDC 1000 M Ω Short circuit protection 1 second(Max) Case material Plastic(UL94-V0) MTBF 3500 K Hours Weigh 1.41 g TYPICAL CHARACTERISTICS Operating Temp.( C) o RECOMMENDED REFLOW SOLDERING PROFILE 100 150 200 250 Time (sec.) 220 C o

10 MaxSec

o

90 Max

(>220 C) o Sec Temperature ( C) o OUTLINE DIMENSIONS & FOOTPRINT DETAILS FOOTPRINT DETAILS Pin Duals 3,6,7 Vin GND +Vo 8 NC NC:No Connection Single Vin GND +V0 NC NC Note: Unit:mm(inch) Pin section:0.60*0.25mm(0.024*0.010inch) Pin tolerances: 0.10mm( 0.004inch) General tolerances: 0.15mm( 0.006inch) + + + + First Angle Projection RECOMMENDED FOOTPRINT Top view,grid:2.54mm(0.1inch) 1234 5876 B_T-1W 6.25 2.54 0.25 4.13 1.35MAX 0.50 5.00 。 1.85MAX 0.3 A 6.76 7.19

11.2 MAX

12.70 7.62 2.54 0.1± 6.007.50 0.60 0.05± (Side view) (Top view) (0.246) (0.236) (0.163) (0.100) (0.100) (0.500) (0.300) (0.295) (0.441) (0.266) (0.020) (0.053) 12 4 B_(X)T-1W NO Pin Requirement on output load To ensure this module can operate efficiently and reliably, During operation, the minimum output load is not less than 10% of the full load, and that this product should never be operated under no load! If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load. Recommended testing circuit If you want to further decrease the input/output ripple, an “LC” filtering network may be connected to the input and output ends of the DC/DC converter, see (Figure 1). LSingle Output Vin GND +Vo DCCin L DC Cout (Figure 1) It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the DC/DC frequency to avoid mutual interference. However, the capacitance o f the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1). EXTERNAL CAPACITOR TABLE (Table 1) Vin (VDC) Cin (uF) Vout (VDC) Cout (uF) 3.3 4.7 3.3 5 4.7 5 10 12 2.2 9 4.7 24 0.47 12 2.2 - - 15 1 - - 24 0.47 It’s not recommend to connect any external capacitor in the application field with less than 0.5 watt output. Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat protection that is connected to the input or output end in series (Figure2). Vi n GN D Vi n GN D REG +V out +Vo ut DC DC DC DC REG （Figure2） Overload Protection Under normal operating conditions, the output circuit of these products has no protection against over-current and short-circuits. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. No parallel connection or plug and play. RSG ELECTRONIC COMPONENTS RSG Electronic Components GmbH ■ Sprendlinger Landstr. 115 ■ D-63069 Offenbach/Germany Tel. +49 69 984047-0 ■ Fax +49 69 984047-77 ■ info@rsg-electronic.de ■ www.rsg-electronic.de Änderungen vorbehalten / subject to change without notice