B13JJHC

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

Series B Subminiature Fully Illuminated Toggles www.nkk.comA20 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable RockersTouch Tilt AToggles General Specifications Electrical Capacity (Resistive Load) Logic Level: 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings Contact Resistance: 50 milliohms maximum Insulation Resistance: 500 megohms minimum @ 500V DC Dielectric Strength: 500V AC minimum for 1 minute minimum Mechanical Life: 100,000 operations minimum Electrical Life: 50,000 operations minimum Nominal Operating Force: 1.18N Contact Timing: Nonshorting (break-before-make) Angle of Throw: 26° Materials & Finishes Actuator: Polyamide Bushing Housing: Polyamide Case Housing: Glass fiber reinforced polyamide Support Bracket: Phosphor bronze with tin plating Movable Contact: Phosphor bronze with gold plating Stationary Contacts: Brass with tin plating Terminals: Brass with gold plating Environmental Data Operating Temperature Range: –25°C through +55°C (–13°F through +131°F) Humidity: 90 ~ 95% humidity for 240 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 5 minutes; 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 3 right angled directions, with 5 shocks in each direction) PCB Processing Soldering: Wave Soldering recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Cleaning: Automated alcohol based cleaning recommended, 5 minutes maximum. Do not use high-purity alcohol (50% alcohol or more) or organic solvent. High alcohol solution can damage clear plastic. See Cleaning specifications in Supplement section. Standards & Certifications The B Series illuminated toggles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy.

Series BSubminiature Fully Illuminated Toggles www.nkk.com A21 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable A TogglesRockersTouch Tilt Distinctive Characteristics LED provides maximum illumination to bushing and actuator, indicating actuator status in highly visible green, red, or amber for single color or red/green for bicolor. (Patent pending.) Totally sealed body construction prevents contact contamination and allows time- and money-saving automated soldering and cleaning. Molded-in, epoxy sealed terminals lock out flux and other contaminants. Award-winning STC contact mechanism with benefits unavailable in conventional mechanisms: smoother, positive detent actuation, increased contact stability, and unparalleled logic-level reliability. (Additional STC details in Terms & Acronyms; see Supplement section.) .100” x .100” (2.54mm x 2.54mm) terminal spacing conforms to standard PC board grid spacing. Actual Size

Series B Subminiature Fully Illuminated Toggles www.nkk.comA22 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable RockersTouch Tilt AToggles Poles

1 SPDT

TYPICAL SWITCH ORDERING EXAMPLE

1 PB 2

DESCRIPTION FOR TYPICAL ORDERING EXAMPLE B12JJPC J C Bushing J Clear J Actuator J Clear SPDT ON-NONE-ON Circuit Clear Toggle & Bushing with Red LED Straight PC Terminals PC Terminals P Straight H Right Angle V Vertical Circuits

2 ON NONE ON

Combines with single color or bicolor LEDs

3 ON OFF ON

& ON-OFF-ON ACTUATOR & BUSHING J Clear Toggle J Clear Bushing 26° (1.9) Dia .075 (3.5) .138 (6.3) .248 Toggle Position Connected Terminals Throw & Schematics Pole Throw Model Up Center Down Up Center Down SPDT B12 B13 ON ON NONE OFF ON ON 2-3 2-3 NONE OPEN 2-1 2-1 POLE & CIRCUITS Slot Slot Note: Terminal numbers are not actually on the switch. LED circuit is isolated and requires an external power source. Single Color Bicolor (5) (4) Red (6) Green (5) (6)2 (COM)

Series BSubminiature Fully Illuminated Toggles www.nkk.com A23 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable A TogglesRockersTouch Tilt PC TERMINALS Straight Right Angle with BracketP H Vertical with BracketV TYPICAL SWITCH DIMENSIONS Terminal 4 is a support pin on single color models. B12JJPC Terminal 4 is a support pin on single color models. B13JJHCF Terminal 4 is a support pin on single color models. B13JJVCF 1 (2.54) Typ .100 (0.8) Dia Typ .031 (5.08) .200 (5.08) .200 (0.8) Dia Typ .031 (2.54) Typ .100 (5.08) .200 (6.0) Dia .236 Slot (8.8) .346 26° (1.9) Dia .075 (0.6) Dia Typ .024 (2.54) Typ .100 (3.1) .122 (13.1) .516 (6.3) .248 (3.5) .138 (0.8) .031 (8.8) .346 (5.08) .200 (0.6) Dia Typ .024 (2.54) Typ .100 (8.8) .346 32 1 4 5 6 (16.42) .646 (3.1) .122 (0.5) .020 (2.54) .100 (1.9) Dia .075 (2.7) .106 (0.4) .016 (5.08) .200 (6.3) .248 Slot (0.6) Typ .024 (6.0) Dia .236 (5.08) .200 (8.8) .346 (0.6) Dia Typ .024 (5.08) .200 (8.8) .346 (18.96) .746 (3.1) .122 (0.5) Typ .020 (2.54) Typ .100 (2.7) .106 (0.4) .016 (5.08) .200 (6.3) .248 26° (1.9) Dia .075 (0.6) Typ .024 (6.0) Dia .236 (5.08) .200 (8.8) .346 Slot 26° 4 6 (2.54) .100 (0.8) Dia Typ .031 (2.54) Typ .100 (5.08) .200 Straight PC Right Angle PC Vertical PC LED COLORS & SPECIFICATIONS Single Color Bicolor Red Amber Green Red/Green Forward Peak Current IFM 30mA 30mA 20mA 30mA/20mA Continuous Forward Current IF 20mA 20mA 10mA 20mA/10mA Reverse Peak Voltage VRM 5V 5V 5V 5V/5V Current Reduction Rate Above 25°C ∆IF 0.43mA/°C 0.28mA/°C 0.43mA/°C/0.28mA/°C Ambient Temperature Range –25°C ~ +55°C D CFFC LEDs are an integral part of the switch and not available separately. The electrical specifications shown are determined at a basic temperature of 25°C. If the source volt- age exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Colors