AVCE6467T

AVCE6467T TI1 | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 44

Technical content

www.ti.com

FEATURES

MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Transceiver for Memory Card Interface ESD Protection for Card-Side Pins Port) [MultiMediaCard (MMC), Secure Digital (SD), kV kV on Pin 14B) IEC 61000-4-2 Memory Stick Compliant Products, ESD, Air-Gap Discharge SmartMedia Card, and xD-Picture Card kV IEC 61000-4-2 ESD, Contact Configurable I/O Switching Levels With Discharge Dual-Supply Pins Operating Over Full 1.4-V to ESD Protection for A-Port Pins (Tested Per 3.6-V Power-Supply Range JESD 22) Exceeds For Low-Power Operation, A Ports Are Placed 2000-V Human-Body Model (A114-B in High-Impedance State When Card-Side 1000-V Charged-Device Model (C101) Supply Voltage Is Switched Off xxxxxxx Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II The SN74AVCA406 is a transceiver for interfacing microprocessors with MultiMediaCards (MMCs), secure digital (SD) cards, Memory Stick compliant products, SmartMedia cards, or xD-Picture Cards It integrates high ESD protection, which eliminates the need for external ESD diodes. Two supply-voltage pins allow the A-port and B-port input switching thresholds to be configured separately. The A port is designed to track V CCA while the B port is designed to track V CCB0 and V CCB1 V CCA CCB0 and V CCB1 can accept any supply voltage from 1.4 V to 3.6 Memory card standards recommend high ESD protection for devices that connect directly to the external memory card. To meet this need, the SN74AVCA406 incorporates 15-kV air-gap discharge and 8-kV contact discharge protection on the card side. If V CCB0 and V CCB1 are switched off (no card inserted), the A-port outputs are placed in the high-impedance state to conserve power. The SN74AVCA406 enables system designers to easily interface low-voltage microprocessors to different memory cards operating at higher voltages. The mode (MODE0 and MODE1) pins are used to configure the device to interface with different types of cards. The SN74AVCA406 is offered in the 48-ball MicroStar Jr. ball grid array (BGA) package. This package has dimensions of mm, with a 0.5-mm ball pitch for effective board-space savings. Memory cards are widely used in mobile phones, PDAs, digital cameras, personal media players, camcorders, set-top boxes, etc. Low static power consumption and small package size make the SN74AVCA406 an ideal choice for these applications. ORDERING INFORMATION T A PACKAGE (1) ORDERABLE PART NUMBER TOP-SIDE MARKING TSSOP DGGR Tape and reel SN74AVCA406DGGR AVCA406 C to C VFBGA GQC Tape and reel SN74AVCA406GQCR WM406 VFBGA ZQC (Pb-free) Tape and reel SN74AVCA406ZQCR (1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical

applications

sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Copyright 2004 2007, Texas Instruments Incorporated Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

www.ti.com GQC/ZQC P ACKAGE (TOP VIEW) G F E D C B A 21 3 4 65 7 SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 TERMINAL ASSIGNMENTS (1) A V CCA 4DIR 2DIR MODE1 10B1 V CCB0 B 10A1 1DIR MODE0 9B1 C 10A2 3DIR GND D 9DIR 56DIR GND 11B 12B E 78DIR GND CS0 GND 10B2 9B2 F 12A 13A 14B G V CCA 11A CS1 V CCB1 (1) V CCA powers all A-port I/Os and control inputs. V CCB0 powers 1B, 2B, 3B, 4B, 9B1, and 10B1. V CCB1 powers 5B, 6B, 7B, 8B, 9B2, 10B2, 11B, 12B, and 14B. Submit Documentation Feedback

www.ti.com DGG P ACKAGE (TOP VIEW) 3DIR 4DIR V CCA GND 10A1 10A2 9DIR 56DIR 78DIR V CCA GND 12A 11A 13A CS1 2DIR 1DIR MODE1 MODE0 10B1 GND V CCB0 9B1 12B 11B 9B2 10B2 14B GND V CCB1 CS0 Device Operation SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 The A port is designed to track V CCA V CCA accepts any supply voltage from 1.4 V to 3.6 The B port is designed to track V CCB0 and V CCB1 V CCB0 and V CCB1 can accept any supply voltage from 1.4 V to 3.6 however, V CCB0 V CCB1 or both must be greater than or equal to V CCA during normal operation. If V CCB0 and V CCB1 are both at GND, the A port is in the high-impedance state. The control pins are supplied by V CCA The microprocessor is connected to the A port, and the memory card(s) are connected to the B port. The device can be configured using MODE0, MODE1, CS0 and CS1 pins to interface with 1-bit, 4-bit, or 8-bit memory cards. Outputs 12A and 14B are push-pull and open drain (OD), respectively, except for NAND flash (XD) mode, where they are open drain and push-pull, respectively. Table Interface With Different Memory Cards MODE0 MODE1 MEMORY-CARD INTERFACE X SD/SDIO/MMC/Memory Stick/Memory Stick PRO 8-bit MMC/4-bit GPIO translation SmartMedia/xD-Picture Card Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Configuration Interfacing With SD or SDIO Card (SD Mode or SD 4-Bit Mode) Table SD or SDIO Card SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power 10A1 CLK.h Clock signal from host Input CMD.h Command signal connected to host I/O 9DIR CMD-dir.h Direction control for 9A/9B connected to host Input 78DIR (tie-high) Direction control for 7A/7B and 8A/8B. Not used in this mode. Tie to V CCA Input (tie-low) I/O pin not used in this mode. Tie to GND. I/O V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power DAT1.h Data bit connected to host. Referenced to V CCA I/O DAT2.h Data bit connected to host. Referenced to V CCA I/O Clock feedback to host for resynchronizing data. Used in OMAP processors. Optional on 10A2 CLK-f.h Output other processors. Leave unconnected if not used. DAT3.h Data bit connected to host. Referenced to V CCA I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Table SD or SDIO Card (continued) SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) 4DIR DAT3-dir.h Direction control for 4A/4B Input DAT0.h Data bit connected to host. Referenced to V CCA I/O Depopulated ball 56DIR (tie-high) Direction control for 5A/5B and 6A/6B. Not used in this mode. Tie to V CCA Input GND GND Ground 12A DNU Output pin not used in this mode. Do not use. Leave unconnected. Output 11A (tie-low) Input pin not used in this mode. Tie to GND. Input 2DIR DAT1-dir.h Direction control for 2A/2B connected to host Input 1DIR DAT0-dir.h Direction control for 1A/1B connected to host Input 3DIR DAT2-dir.h Direction control for 3A/3B connected to host Input GND GND Ground Card select from host. Active low. When CS0 high, 1A, 2A, 3A, 4A, 1B, 2B, 3B, 4B, 9A, CS0 CS0 Input 9B1, and 10A2 are placed in Hi and 10B1 is low. 13A (tie-low) Input pin not used in this mode. Tie to GND. Input CS1 (tie-high) Card select. Not used in this mode. Tie to V CCA for proper operation. Input MODE1 (tie-low) Input MODE1, MODE0 determine mode of operation (see Table Tie to GND in this mode. MODE0 (tie-low) Input GND GND Ground DAT3 Data bit connected to card. Referenced to V CCB0 I/O GND GND Ground DNU I/O pin not used in this mode. Leave unconnected. I/O DNU I/O pin not used in this mode. Leave unconnected. I/O 10B1 CLK Clock signal connected to card Output 9B1 CMD Command signal connected to card Output DAT1 Data bit connected to card. Referenced to V CCB0 I/O 11B DNU Output pin not used in this mode. Do not use. Leave unconnected. Output 10B2 DNU Output pin not used in this mode. Do not use. Leave unconnected. Output DNU I/O pin not used in this mode. Leave unconnected. I/O DNU I/O pin not used in this mode. Leave unconnected. I/O V CCB0 V CCB0 B-port supply voltage. V CCB0 powers 1B, 2B, 3B, 4B, 9B1, and 10B1. Power DAT0 Data bit connected to card. Referenced to V CCB0 I/O DAT3 Data bit connected to card. Referenced to V CCB0 I/O 12B (tie-low) Input pin not used in this mode. Tie to GND. Input 9B2 DNU I/O pin not used in this mode. Leave unconnected. I/O 14B DNU Open-drain output not used in this mode. Leave unconnected. Output B-port supply voltage. V CCB1 powers 5B, 6B, 7B, 8B, 9B2, 10B2, 11B, 12B, and 14B. Not V CCB1 (tie-low) Power used in this mode. Tie to GND. Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Configuration Interfacing With SD Card or MMC (SD 1-Bit Mode or MMC Mode) Table SD Card or MMC SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power 10A1 CLK.h Clock signal from host Input CMD.h Command signal connected to host I/O 9DIR CMD-dir.h Direction control for 9A/9B Input 78DIR (tie-high) Direction control for 7A/7B and 8A/8B. Not used in this mode. Tie to V CCA Input (tie-low) I/O pin not used in this mode. Tie to GND. I/O V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O Clock feedback to host for resynchronizing data. Used in OMAP processors. Optional on 10A2 CLK-f.h Output other processors. Leave unconnected if not used. (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Table SD Card or MMC (continued) SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) 4DIR (tie-high) Direction control for 4A/4B. Not used in this mode. Tie to V CCA Input DAT0.h Data bit connected to host. Referenced to V CCA I/O Depopulated ball 56DIR (tie-high) Direction control for 5A/5B and 6A/6B. Not used in this mode. Tie to V CCA Input GND GND Ground 12A DNU Output pin not used in this mode. Do not use. Leave unconnected. Output 11A (tie-low) Input pin not used in this mode. Tie to GND. Input 2DIR (tie-high) Direction control for 2A/2B connected to host. Not used in this mode. Tie to V CCA Input 1DIR DAT0-dir.h Direction control for 1A/1B connected to host Input 3DIR (tie-high) Direction control for 3A/3B connected to host. Not used in this mode. Tie to V CCA Input GND GND Ground Card select from host. Active low. When CS0 high, 1A, 2A, 3A, 4A, 1B, 2B, 3B, 4B, and CS0 CS0 Input 9B1 are placed in Hi 13A (tie-low) Input pin not used in this mode. Tie to GND. Input CS1 (tie-high) Card select. Not used in this mode. Tie to V CCA for proper operation. Input MODE1 (tie-low) Input MODE1, MODE0 determine mode of operation (see Table Tie to GND in this mode. MODE0 (tie-low) Input GND GND Ground DNU I/O pin not used in this mode. Leave unconnected. I/O GND GND Ground DNU I/O pin not used in this mode. Leave unconnected. I/O DNU I/O pin not used in this mode. Leave unconnected. I/O 10B1 CLK Clock signal connected to card Output 9B1 CMD Command signal connected to card Output DNU I/O pin not used in this mode. Leave unconnected. I/O 11B DNU Output pin not used in this mode. Do not use. Leave unconnected. Output 10B2 DNU Output pin not used in this mode. Do not use. Leave unconnected. Output DNU I/O pin not used in this mode. Leave unconnected. I/O DNU I/O pin not used in this mode. Leave unconnected. I/O V CCB0 V CCB0 B-port supply voltage. V CCB0 powers 1B, 2B, 3B, 4B, 9B1, and 10B1. Power DAT0 Data bit connected to card. Referenced to V CCB0 I/O DNU I/O pin not used in this mode. Leave unconnected. I/O 12B (tie-low) Input pin not used in this mode. Tie to GND. Input 9B2 DNU I/O pin not used in this mode. Leave unconnected. I/O 14B DNU Open-drain output not used in this mode. Leave unconnected. Output B-port supply voltage. V CCB1 powers 5B, 6B, 7B, 8B, 9B2, 10B2, 11B, 12B, and 14B. Not V CCB1 (tie-low) Power used in this mode. Tie to GND. Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Configuration Interfacing With SD/SDIO Card or MMC (SPI Mode) Table SD/SDIO Card or MMC SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power 10A1 SCLK.h Serial clock signal from host Input Serial data in (master out slave in) connected to host. Connect 9DIR to V CCA to make DI.h I/O an input. 9DIR (tie-high) Direction control for 9A/9B. Tie high to make an input and an output. Input 78DIR (tie-high) Direction control for 7A/7B and 8A/8B. Not used in this mode. Tie to V CCA Input (tie-low) I/O pin not used in this mode. Tie to GND. I/O V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power CS.h Card select connected to host. Connect 2DIR to V CCA to make an input. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O 10A2 DNU Clock feedback to host. Not used in this mode. Leave unconnected. Output (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Table SD/SDIO Card or MMC (continued) SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) 4DIR (tie-high) Direction control for 4A/4B. Not used in this mode. Tie to V CCA Input Serial data out (master in slave out) connected to host. Connect 1DIR to GND to make DO.h I/O an output. Depopulated ball 56DIR (tie-high) Direction control for 5A/5B and 6A/6B. Not used in this mode. Tie to V CCA Input GND GND Ground 12A DNU Output pin not used in this mode. Do not use. Leave unconnected. Output 11A (tie-low) Input pin not used in this mode. Tie to GND. Input 2DIR (tie-high) Direction control for 2A/2B. Tie to V CCA to make an input and an output. Input 1DIR (tie-low) Direction control for 1A/1B. Tie to GND to make an input and an output. Input 3DIR (tie-high) Direction control for 3A/3B. Not used in this mode. Tie to V CCA Input GND GND Ground CS0 (tie-low) Card select signal. Not used in this mode. For proper operation, tie to GND. Input 13A (tie-low) Input pin not used in this mode. Tie to GND. Input CS1 (tie-HIGH) Card select. Not used in this mode. For proper operation, tie to V CCA Input MODE1 (tie-low) Input MODE1, MODE0 determine mode of operation (see Table 1). Tie to GND in this mode. MODE0 (tie-low) Input GND GND Ground DNU Card select connected to card. Connect 2DIR to V CCA to make an output. I/O GND GND Ground DNU I/O pin not used in this mode. Leave unconnected. I/O DNU I/O pin not used in this mode. Leave unconnected. I/O 10B1 SCLK Serial clock signal connected to card Output 9B1 DI Serial data in (master out slave in) connected to card Output CS I/O pin not used in this mode. Leave unconnected. I/O 11B DNU Output pin not used in this mode. Leave unconnected. Output 10B2 DNU Output pin not used in this mode. Leave unconnected. Output DNU I/O pin not used in this mode. Leave unconnected. I/O DNU I/O pin not used in this mode. Leave unconnected. I/O V CCB0 V CCB0 B-port supply voltage. V CCB0 powers 1B, 2B, 3B, 4B, 9B1, and 10B1. Power Serial data out (master in slave out) connected to host. Connect 1DIR to GND to make DO I/O an input. DNU I/O pin not used in this mode. Leave unconnected. I/O 12B (tie-low) Input pin not used in this mode. Tie to GND. Input 9B2 DNU I/O pin not used in this mode. Leave unconnected. I/O 14B DNU Open-drain output not used in this mode. Leave unconnected. Output B-port supply voltage. V CCB1 powers 5B, 6B, 7B, 8B, 9B2, 10B2, 11B, 12B, and 14B. Not V CCB1 (tie-low) Power used in this mode. Tie to GND. Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Configuration Interfacing With SDIO Card in Slot and SD Card (4-bit Mode) in Slot Table SDIO Card (Slot and SD Card (Slot SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power 10A1 CLK.h Clock signal from host Input CMD.h Command signal connected to host I/O 9DIR CMD-dir.h Direction control for 9A/9B connected to host Input 78DIR (tie-high) Direction control for 7A/7B and 8A/8B. Not used in this mode. Tie to V CCA Input (tie-low) I/O pin not used in this mode. Tie to GND. I/O V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power DAT1.h Data bit connected to host. Referenced to V CCA I/O DAT2.h Data bit connected to host. Referenced to V CCA I/O Clock feedback to host for resynchronizing data. Used in OMAP processors. Optional on 10A2 CLK-f.h Output other processors. Leave unconnected if not used. DAT3.h Data bit connected to host. Referenced to V CCA I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O 4DIR DAT3-dir.h Direction control for 4A/4B Input Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Table SDIO Card (Slot and SD Card (Slot (continued) SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) DAT0.h Data bit connected to host. Referenced to V CCA I/O Depopulated ball 56DIR (tie-high) Direction control for 5A/5B and 6A/6B. Not used in this mode. Tie to V CCA Input GND GND Ground 12A DNU Output pin not used in this mode. Do not use. Leave unconnected. Output 11A (tie-low) Input pin not used in this mode. Tie to GND Input 2DIR DAT1-dir.h Direction control for 2A/2B connected to host Input 1DIR DAT0-dir.h Direction control for 1A/1B connected to host Input 3DIR DAT2-dir.h Direction control for 3A/3B connected to host Input GND GND Ground Card select from host. Active low. When CS0 high, 1A, 2A, 3A, 4A, 1B, 2B, 3B, 4B, and CS0 CS0 Input 9B1 are placed in Hi and 10B1 is low. 13A (tie-low) Input pin not used in this mode. Tie to GND. Input Card select from host. Active low. When CS1 high, 5A, 6A, 7A, 8A, 5B, 6B, 7B, 8B, 7B, CS1 CS1 Input and 9B2 are placed in Hi and 10B2 is low. MODE1 (tie-low) Input MODE1, MODE0 determine mode of operation (see Table 1). Tie to GND in this mode. MODE0 (tie-low) Input GND GND Ground DAT3.0 Data bit connected to card in slot Referenced to V CCB0 I/O GND GND Ground DAT2.1 Data bit connected to card in slot Referenced to V CCB1 I/O DAT3.1 Data bit connected to card in slot Referenced to V CCB1 I/O 10B1 CLK.0 Clock signal connected to card in slot Output 9B1 CMD.0 Command signal connected to card in slot Output DAT1.0 Data bit connected to card in slot Referenced to V CCB0 I/O 11B DNU Output pin not used in this mode. Leave unconnected. Output 10B2 CLK.1 Clock signal connected to card in slot Output DAT0.1 Data bit connected to card in slot Referenced to V CCB1 I/O DAT1.1 Data bit connected to card in slot Referenced to V CCB1 I/O V CCB0 V CCB0 B-port supply voltage. V CCB0 powers 1B, 2B, 3B, 4B, 9B1, and 10B1. Power DAT0.0 Data bit connected to card in slot Referenced to V CCB0 I/O DAT2.0 Data bit connected to card in slot Referenced to V CCB0 I/O 12B (tie-low) Input pin not used in this mode. Tie to GND. Input 9B2 CMD.1 Command signal connected to card in slot I/O Open-drain interrupt output for dual SDIO cards configuration. DAT1 is the input for 14B IRQ Output interrupt. V CCB1 V CCB1 B-port supply voltage. V CCB1 powers 5B, 6B, 7B, 8B, 9B2, 10B2, 11B, 12B, and 14B. Power Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Configuration Alternate Method of Interfacing With SD/SDIO Card (SD Mode or SD 4-bit Mode) Table Alternate SD/SDIO Card SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power 10A1 CLK.h Clock signal from host Input CMD.h Command signal connected to host I/O 9DIR CMD-dir.h Direction control for 9A/9B connected to host Input 78DIR (tie-high) Direction control for 7A/7B and 8A/8B. Not used in this mode. Tie to V CCA Input (tie-low) I/O pin not used in this mode. Tie to GND. I/O V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power DAT1.h Data bit connected to host. Referenced to V CCA I/O DAT2.h Data bit connected to host. Referenced to V CCA I/O Clock feedback to host for resynchronizing data. Used in OMAP processors. Optional on 10A2 CLK-f.h Output other processors. Leave unconnected if not used. DAT3.h Data bit connected to host. Referenced to V CCA I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Table Alternate SD/SDIO Card (continued) SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) 4DIR DAT3-dir.h Direction control for 4A/4B Input DAT0.h Data bit connected to host. Referenced to V CCA I/O Depopulated ball 56DIR (tie-high) Direction control for 5A/5B and 6A/6B. Not used in this mode. Tie to V CCA Input GND GND Ground 12A DNU Output pin not used in this mode. Do not use. Leave unconnected. Output 11A (tie-low) Input pin not used in this mode. Tie to GND. Input 2DIR DAT1-dir.h Direction control for 2A/2B connected to host Input 1DIR DAT0-dir.h Direction control for 1A/1B connected to host Input 3DIR DAT2-dir.h Direction control for 3A/3B connected to host Input GND GND Ground CS0 (tie-high) Card select signal. Not used in this mode. Tie to V CCA for proper operation. Input 13A (tie-low) Input pin not used in this mode. Tie to GND. Input Card select from host. Active low. When CS1 high, 1A, 2A, 3A, 4A, 5B, 6B, 7B, 8B, 9A, CS1 CS1 Input 9B2, and 10A2 are placed in Hi and 10B1 is low. MODE1 (tie-low) Input MODE1, MODE0 determine mode of operation (see Table 1). Tie to GND in this mode. MODE0 (tie-low) Input GND GND Ground DNU I/O pin not used in this mode. Leave unconnected. I/O GND GND Ground DAT2 Data bit connected to card. Referenced to V CCB1 I/O DAT3 Data bit connected to card. Referenced to V CCB1 I/O 10B1 DNU Output pin not used in this mode. Leave unconnected. Output 9B1 DNU Output pin not used in this mode. Leave unconnected. Output DNU I/O pin not used in this mode. Leave unconnected. I/O 11B DNU Output pin not used in this mode. Leave unconnected. Output 10B2 CLK Clock signal connected to card Output DAT0 Data bit connected to card. Referenced to V CCB1 I/O DAT1 Data bit connected to card. Referenced to V CCB1 I/O B-port supply voltage. V CCB0 powers 1B, 2B, 3B, 4B, 9B1, and 10B1. V CCB0 (tie-low) Power Not used in this mode. Tie to GND. DNU I/O pin not used in this mode. Leave unconnected. I/O DNU I/O pin not used in this mode. Leave unconnected. I/O 12B (tie-low) Input pin not used in this mode. Tie to GND. Input 9B2 CMD Command signal connected to card I/O 14B DNU Open-drain output not used in this mode. Leave unconnected. Output V CCB1 V CCB1 B-port supply voltage. V CCB1 powers 5B, 6B, 7B, 8B, 9B2, 10B2, 11B, 12B, and 14B. Power Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Configuration Interfacing With Memory Stick Table Memory Stick SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power 10A1 SCLK.h Clock signal from host Input BS.h Bus state connected to host I/O 9DIR (tie-high) Direction control for 9A/9B connected to host. Tie high to make an input, an output. Input 78DIR (tie-high) Direction control for 7A/7B and 8A/8B. Not used in this mode. Tie to V CCA Input (tie-low) I/O pin not used in this mode. Tie to GND. I/O V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power DATA1.h Data bit connected to host. Referenced to V CCA I/O DATA2.h Data bit connected to host. Referenced to V CCA I/O Clock feedback to host for resynchronizing data. Used in OMAP processors. Optional on 10A2 SCLK-f.h Output other processors. Leave unconnected if not used. DATA3.h Data bit connected to host. Referenced to V CCA I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O (tie-low) I/O pin not used in this mode. Tie to GND. I/O Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Table Memory Stick (continued) SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) 4DIR DATU-dir.h Direction control for 4A/4B Input DATA0.h Data bit connected to host. Referenced to V CCA I/O Depopulated ball 56DIR (tie-high) Direction control for 5A/5B and 6A/6B. Not used in this mode. Tie to V CCA Input GND GND Ground 12A DNU Output pin not used in this mode. Do not use. Leave unconnected. Output 11A (tie-low) Input pin not used in this mode. Tie to GND. Input 2DIR DATU-dir.h Direction control for 2A/2B connected to host Input 1DIR DAT0-dir.h Direction control for 1A/1B connected to host Input 3DIR DATU-dir.h Direction control for 3A/3B connected to host Input GND GND Ground Card select from host. Active low. When CS0 high, 1A, 2A, 3A, 4A, 1B, 2B, 3B, 4B, 9A, CS0 CS0 Input 9B1, and 10A2 are placed in Hi and 10B1 is low. 13A (tie-low) Input pin not used in this mode. Tie to GND. Input CS1 (tie-high) Card select signal. Not used in this mode. Tie to V CCA for proper operation. Input MODE1 (tie-low) Input MODE1, MODE0 determine mode of operation (see Table 1). Tie to GND in this mode. MODE0 (tie-low) Input GND GND Ground DATA3 Data bit connected to card. Referenced to V CCB0 I/O GND GND Ground DNU I/O pin not used in this mode. Leave unconnected. I/O DNU I/O pin not used in this mode. Leave unconnected. I/O 10B1 SCLK Clock signal connected to card Output 9B1 BS Bus state signal connected to card Output DATA1 Data bit connected to card. Referenced to V CCB0 I/O 11B DNU Output pin not used in this mode. Leave unconnected. Output 10B2 DNU Output pin not used in this mode. Leave unconnected. Output DNU I/O pin not used in this mode. Leave unconnected. I/O DNU I/O pin not used in this mode. Leave unconnected. I/O V CCB0 V CCB0 B-port supply voltage. V CCB0 powers 1B, 2B, 3B, 4B, 9B1, and 10B1. Power DATA0 Data bit connected to card. Referenced to V CCB0 I/O DATA2 Data bit connected to card. Referenced to V CCB0 I/O 12B (tie-low) Input pin not used in this mode. Tie to GND. Input 9B2 DNU I/O pin not used in this mode. Leave unconnected. I/O 14B DNU Open-drain output not used in this mode. Leave unconnected. Output B-port supply voltage. V CCB1 powers 5B, 6B, 7B, 8B, 9B2, 10B2, 11B, 12B, and 14B. Not V CCB1 (tie-low) Power used in this mode. Tie to GND. Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 CONFIGURATION FUNCTION TABLE (MODE0 MODE1 INPUTS OPERATION SIGNAL CS0 CS1 9DIR (1-4)DIR MMC/SD Memory Stick/Memory Stick PRO CLK.0 and CLK.1 forced low, SCLK.0 and SCLK.1 forced low, H H X X CLK-f.h forced Hi Z SCLK-f.h forced Hi Z CLK.h to CLK.0 and CLK.1, SCLK.h to SCLK.0 and SCLK.1, L L X X CLK.0 to CLK-f.h SCLK.0 to SCLK-f.h CLK.h to CLK.0, SCLK.h to SCLK.0, Clock L H X X CLK.0 to CLK-f.h, SCLK.0 to SCLK-f.h, CLK.1 forced low SCLK.1 forced low CLK.h to CLK.1, SCLK.h to SCLK.1, H L X X CLK.1 to CLK-f.h, SCLK.1 to SCLK-f.h, CLK.0 forced low SCLK.0 forced low H H X X All data I/Os are Hi Z (isolation mode). All data I/Os are Hi Z (isolation mode). DAT0.0 and DAT0.1 to DAT0.h, DATA0.0 and DATA0.1 to DATA0.h, DAT1.0 and DAT1.1 to DAT1.h, DATA1.0 and DATA1.1 to DATA1.h, L (1) L (1) X L DAT2.0 and DAT2.1 to DAT2.h, DATA2.0 and DATA2.1 to DATA2.h, DAT3.0 and DAT3.1 to DAT3.h DATA3.0 and DATA3.1 to DATA3.h DAT0.h to DAT0.0 and to DAT0.1, DATA0.h to DATA0.0 and to DATA0.1, DAT1.h to DAT1.0 and to DAT1.1, DATA1.h to DATA1.0 and to DATA1.1, L (1) L (1) X H DAT2.h to DAT2.0 and to DAT2.1, DATA2.h to DATA2.0 and to DATA2.1, DAT3.h to DAT3.0 and to DAT3.1 DATA3.h to DATA3.0 and to DATA3.1 DAT0.0 to DAT0.h, DATA0.0 to DATA0.h, DAT1.0 to DAT1.h, DATA1.0 to DATA1.h, L H X L DAT2.0 to DAT2.h, DATA2.0 to DATA2.h, Data DAT3.0 to DAT3.h DATA3.0 to DATA3.h DAT0.h to DAT0.0, DATA0.h to DATA0.0, DAT1.h to DAT1.0, DATA1.h to DATA1.0, L H X H DAT2.h to DAT2.0, DATA2.h to DATA2.0, DAT3.h to DAT3.0 DATA3.h to DATA3.0 DAT0.1 to DAT0.h, DATA0.1 to DATA0.h, DAT1.1 to DAT1.h, DATA1.1 to DATA1.h, H L X L DAT2.1 to DAT2.h, DATA2.1 to DATA2.h, DAT3.1 to DAT3.h DATA3.1 to DATA3.h DAT0.h to DAT0.1, DATA0.h to DATA0.1, DAT1.h to DAT1.1, DATA1.h to DATA1.1, H L X H DAT2.h to DAT2.1, DATA2.h to DATA2.1, DAT3.h to DAT3.1 DATA3.h to DATA3.1 CMD.h, CMD.0, and CMD.1 are Hi Z BS.h, BS.0, and BS.1 are Hi Z (isolation H H X X (isolation mode). mode). L L H X CMD.h to CMD.0 and CMD.1 BS.h to BS.0 and BS.1 L L L X CMD.0 and CMD.1 to CMD.h BS.0 and BS.1 to BS.h Command L H H X CMD.h to CMD.0 BS.h to BS.0 L H L X CMD.0 to CMD.h BS.0 to BS.h H L H X CMD.h to CMD.1 BS.h to BS.1 H L L X CMD.1 to CMD.h BS.1 to BS.h DAT1.0 and DAT1.1 to IRQ DATA1.0 and DATA1.1 to IRQ H H X X IRQ is an open-drain output. IRQ is an open-drain output. DAT1.1 to IRQ DATA1.1 to IRQ L H X X Interrupt IRQ is an open-drain output. IRQ is an open-drain output. request DAT1.0 to IRQ DATA1.0 to IRQ H L X X IRQ is an open-drain output. IRQ is an open-drain output. L L X X IRQ is Hi IRQ is Hi (1) Broadcast mode in which the host writes to or reads from both cards in parallel Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Configuration Interfacing With SD/SDIO Card and Using GPIOs for Level Shifting Table SD/SDIO Card Using GPIOs for Level Shifting SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power 10A1 CLK.h Clock signal from host Input CMD.h Command signal connected to host I/O 9DIR CMD-dir.h Direction control for 9A/9B connected to host Input 78DIR I/O23-dir.h Direction control for 7A/7B and 8A/8B. Connected to host. Tie to V CCA if unused. Input I/O2.h General-purpose I/O. Referenced to V CCA Tie to V CCA or GND if unused. I/O V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power DAT1.h Data bit connected to host. Referenced to V CCA I/O DAT2.h Data bit connected to host. Referenced to V CCA I/O Clock feedback to host for resynchronizing data. Used in OMAP processors. Optional on 10A2 CLK-f.h Output other processors. Leave unconnected if not used. DAT3.h Data bit connected to host. Referenced to V CCA I/O I/O1.h General-purpose I/O. Referenced to V CCA Tie to V CCA or GND if unused. I/O I/O3.h General-purpose I/O. Referenced to V CCA Tie to V CCA or GND if unused. I/O I/O0.h General-purpose I/O. Referenced to V CCA Tie to V CCA or GND if unused. I/O Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Table SD/SDIO Card Using GPIOs for Level Shifting (continued) SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) 4DIR DAT3-dir.h Direction control for 4A/4B Input DAT0.h Data bit connected to host. Referenced to V CCA I/O Depopulated ball 56DIR I/O01-dir.h Direction control for 5A/5B and 6A/6B. Referenced to V CCA Tie to V CCA if unused. Input GND GND Ground 12A O5.h General-purpose output connected to host. Referenced to V CCA Output 11A I4.h General-purpose input connected to host. Referenced to V CCA Input 2DIR DAT1-dir.h Direction control for 2A/2B connected to host Input 1DIR DAT0-dir.h Direction control for 1A/1B connected to host Input 3DIR DAT2-dir.h Direction control for 3A/3B connected to host Input GND GND Ground Card select from host. Active low. When CS0 high, 1A, 2A, 3A, 4A, 1B, 2B, 3B, 4B, 9A, CS0 CS0 Input 9B, and 10A2 are placed in Hi and 10B1 is low. 13A I6.h General-purpose input connected to host. Referenced to V CCA Input CS1 (tie-low) Card select. Tie to GND for proper operation. Input MODE1 (tie-low) Input MODE1, MODE0 determine mode of operation (see Table 1). Tie MODE0 to V CCA Tie MODE1 to GND. MODE0 (tie-high) Input GND GND Ground DAT3 Data bit connected to card. Referenced to V CCB0 I/O GND GND Ground I/O2 General-purpose I/O. Referenced to V CCB1 I/O I/O3 General-purpose I/O. Referenced to V CCB1 I/O 10B1 CLK Clock signal connected to card Output 9B1 CMD Command signal connected to card Output DAT1 Data bit connected to card. Referenced to V CCB0 I/O 11B General-purpose output. Referenced to V CCB1 Output 10B2 General-purpose output. Referenced to V CCB1 Output I/O0 General-purpose I/O. Referenced to V CCB1 I/O I/O1 General-purpose I/O. Referenced to V CCB1 I/O V CCB0 V CCB0 B-port supply voltage. V CCB0 powers 1B, 2B, 3B, 4B, 9B1, and 10B1. Power DAT0 Data bit connected to card. Referenced to V CCB0 I/O DAT2 Data bit connected to card. Referenced to V CCB0 I/O 12B General-purpose input. Referenced to V CCB1 Input 9B2 DNU I/O pin not used in this mode. Leave unconnected. I/O 14B DNU Open-drain output not used in this mode. Leave unconnected. Output V CCB1 V CCB1 B-port supply voltage. V CCB1 powers 5B, 6B, 7B, 8B, 9B2, 10B2, 11B, 12B, and 14B. Power Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 CONFIGURATION FUNCTION TABLE (MODE0 MODE1 INPUTS OPERATION SIGNAL Memory Stick/ CS0 CS1 9DIR (1-4)DIR 56DIR 78DIR MMC/SD Memory Stick PRO CLK forced low, SCLK forced low, H H X X X X CLK-f.h forced Hi Z SCLK-f.h forced Hi Z Clock CLK.h to CLK, SCLK.h to SCLK, L L X X X X CLK to CLK-f.h SCLK to SCLK-f.h All data I/Os are Hi Z All data I/Os are Hi Z H H X X X X (isolation mode). (isolation mode). DAT0 to DAT0.h, DATA0 to DATA0.h, DAT1 to DAT1.h, DATA1 to DATA1.h, L L X L X X DAT2 to DAT2.h, DATA2 to DATA2.h, Data DAT3 to DAT3.h DATA3 to DATA3.h DAT0.h to DAT0, DATA0.h to DATA0, DAT1.h to DAT1, DATA1.h to DATA1, L L X H X X DAT2.h to DAT2, DATA2.h to DATA2, DAT3.h to DAT3 DATA3.h to DATA3 CMD.h and CMD are Hi Z BS.h and BS are Hi Z H H X X X X (isolation mode). (isolation mode). Command L L L X X X CMD to CMD.h BS to BS.h L L H X X X CMD.h to CMD BS.h to BS H H X X X X All GPIOs are Hi All GPIOs are Hi to O4, to O4, L L X X X X to O5, to O5, to to I/O0 to I/O0.h, I/O0 to I/O0.h, L L X X L X I/O1 to I/O1.h I/O1 to I/O1.h GPIO I/O0.h to I/O0, I/O0.h to I/O0, L L X X H X I/O1.h to I/O1 I/O1.h to I/O1 I/O2 to I/O2.h, I/O2 to I/O2.h, L L X X X L I/O3 to I/O3.h I/O3 to I/O3.h I/O2.h to I/O2, I/O2.h to I/O2, L L X X X H I/O3.h to I/O3 I/O3.h to I/O3 Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Table 8-Bit MMC SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power 10A1 CLK.h Clock signal from host Input CMD.h Command signal connected to host I/O 9DIR CMD-dir.h Direction control for 9A/9B connected to host Input 78DIR DATU-dir.h Direction control for 7A/7B and 8A/8B. Connected to host. Input DAT6.h General-purpose I/O. Referenced to V CCA I/O V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power DAT1.h Data bit connected to host. Referenced to V CCA I/O DAT2.h Data bit connected to host. Referenced to V CCA I/O Clock feedback to host for resynchronizing data. Used in OMAP processors. Optional on 10A2 CLK-f.h Output other processors. Leave unconnected if not used. DAT3.h Data bit connected to host. Referenced to V CCA I/O DAT5.h General-purpose I/O. Referenced to V CCA I/O DAT7.h General-purpose I/O. Referenced to V CCA I/O DAT4.h General-purpose I/O. Referenced to V CCA I/O 4DIR DAT3-dir.h Direction control for 4A/4B Input DAT0.h Data bit connected to host. Referenced to V CCA I/O Depopulated ball 56DIR DATU-dir.h Direction control for 5A/5B and 6A/6B. Referenced to V CCA Input GND GND Ground 12A DNU Output pin not used in this mode. Do not use. Leave unconnected. Output 11A (tie-low) Input pin not used in this mode. Tie to GND. Input 2DIR DAT1-dir.h Direction control for 2A/2B connected to host Input 1DIR DAT0-dir.h Direction control for 1A/1B connected to host Input 3DIR DAT2-dir.h Direction control for 3A/3B connected to host Input GND GND Ground Card select from host. Active low. When CS0 high, 1A, 2A, 3A, 4A, 1B, 2B, 3B, 4B, and CS0 CS0 Input 9B1 are placed in Hi and 10B1 is low. 13A (tie-low) Input pin not used in this mode. Tie to GND. Input CS1 (tie-low) Card select signal. For proper operation, tie to GND. Input MODE1 (tie-low) Input MODE1, MODE0 determine mode of operation (see Table 1). Tie MODE0 to V CCA Tie MODE1 to GND. MODE0 (tie-high) Input GND GND Ground DAT3 Data bit connected to card. Referenced to V CCB I/O GND GND Ground DAT6 Data bit connected to card. Referenced to V CCB I/O DAT7 Data bit connected to card. Referenced to V CCB I/O 10B1 CLK Clock signal connected to card Output 9B1 CMD Command signal connected to card Output DAT1 Data bit connected to card. Referenced to V CCB0 I/O 11B DNU Output pin not used in this mode. Leave unconnected. Output 10B2 DNU Output pin not used in this mode. Leave unconnected. Output DAT4 Data bit connected to card. Referenced to V CCB I/O DAT5 Data bit connected to card. Referenced to V CCB I/O V CCB0 V CCB0 B-port supply voltage. V CCB0 powers 1B, 2B, 3B, 4B, 9B1, and 10B1. Power DAT0 Data bit connected to card. Referenced to V CCB0 I/O Submit Documentation Feedback

www.ti.com Host AVCA406 A Side B Side SmartMedia/ xD-Picture Card VCCA VCCB SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Configuration Interfacing With SmartMedia or xD-Picture Card Table 10. SmartMedia or xD-Picture Card SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power 10A1 RE Read enable connected to host Input CLE.h Command latch enable connected to host I/O 9DIR (tie-low) Input pin not used in this mode. Tie to GND. Input 78DIR I/O-dir.h Data direction control from host Input I/O7.h Data I/O connected to host. Referenced to V CCA I/O V CCA V CCA A-port supply voltage. V CCA powers all A-port I/Os and control inputs. Power I/O2.h Data I/O connected to host. Referenced to V CCA I/O I/O3.h Data I/O connected to host. Referenced to V CCA I/O Read enable feedback to host. Used with OMAP processors. Use with other processors is 10A2 RE -f.h Output optional. Leave unconnected if not used. I/O4.h Data I/O connected to host. Referenced to V CCA I/O I/O6.h Data I/O connected to host. Referenced to V CCA I/O I/O8.h Data I/O connected to host. Referenced to V CCA I/O I/O5.h Data I/O connected to host. Referenced to V CCA I/O 4DIR I/O-dir.h Data direction control connected to host Input I/O1.h Data I/O connected to host. Referenced to V CCA I/O Depopulated ball 56DIR I/O-dir.h Data direction control connected to host Input GND GND Ground 12A R/B.h Read/busy connected to host. Open-drain output. Output 11A WP Write protect connected to host Input 2DIR I/O-dir.h Data direction control connected to host Input 1DIR I/O-dir.h Data direction control connected to host Input 3DIR I/O-dir.h Data direction control connected to host Input GND GND Ground CS0 CE Chip enable from host Input 13A WE Write enable from host Input CS1 ALE.h Address latch enable connected to host Input MODE1 (tie-high) Input MODE1, MODE0 determine mode of operation (see Table 1). Tie to V CCA MODE0 (tie-high) Input Submit Documentation Feedback

www.ti.com SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Table 10. SmartMedia or xD-Picture Card (continued) SIGNAL NAME PIN PIN PIN OR PIN FUNCTION NO. NAME TYPE (CONNECTION) GND GND Ground I/O4 Data I/O connected to card. Referenced to V CCB I/O GND GND Ground I/O7 Data I/O connected to card. Referenced to V CCB I/O I/O8 Data I/O connected to card. Referenced to V CCB I/O 10B1 RE Read enable connected to card Output 9B1 CLE Command latch enable connected to card Output I/O2 Data I/O connected to card. Referenced to V CCB I/O 11B WP Write protect connected to card Output 10B2 WE Write enable connected to card Output I/O5 Data I/O connected to card. Referenced to V CCB I/O I/O6 Data I/O connected to card. Referenced to V CCB I/O V CCB0 V CCB B-port supply voltage. V CCB0 powers 1B, 2B, 3B, 4B, 9B1, and 10B1. Power I/O1 Data I/O connected to card. Referenced to V CCB I/O I/O3 Data I/O connected to card. Referenced to V CCB I/O 12B R/B Read/busy connected to card Input 9B2 ALE Address latch enable connected to host I/O 14B CE Chip enable connected to card Output V CCB1 V CCB B-port supply voltage. V CCB1 powers 5B, 6B, 7B, 8B, 9B2, 10B2, 11B, 12B, and 14B. Power CONFIGURATION FUNCTION TABLE (MODE0 MODE1 8-BIT SmartMedia/xD-Picture Card) INPUTS SIGNAL OPERATION CS0 CS1 9DIR (1-4)DIR 56DIR 78DIR X X X X X X WE to WE Clock L X X X X X RE to RE RE to RE-f H X X X X X All data I/Os are Hi Z (isolation mode). Data LX X X L L L I/O(1-8) to I/O(1-8).h L X X H H H I/O(1-8).h to I/O(1-8) Command X X X X X X CLE.h to CLE, ALE.h to ALE Interrupt request X X X X X X CE.h to CE WP to WP R/B to R/B.h Others X X X X X X (R/B.h is an open-drain output) Submit Documentation Feedback

www.ti.com 10A1 10B1 TP (2) 10B2 13A 10A2 CLK Path CTRL (1) CTRL (1) CTRL (1) (1) CTRL represents a decoded MODE0, MODE1, CS0, and CS1 state. (2) Translation point TP (2) TP (2) TP (2) CTRL (1) CTRL (1) SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 LOGIC DIAGRAMS (POSITIVE LOGIC) Submit Documentation Feedback

www.ti.com B (5, 6, 7, 8) Data Path CTRL (1) CTRL (1) (1) CTRL represents a decoded MODE0, MODE1, CS0, and CS1 state. (2) Translation point CTRL (1) CTRL (1) CTRL (1) CTRL (1) B (1, 2, 3, 4) DIR (1, 2, 3, 4) DIR (5, 6, 7, 8) A (1, 2, 3, 4) A (5, 6, 7, 8) CTRL (1) TP (2) TP (2) TP (2) TP (2) TP (2) TP (2) TP (2) SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Submit Documentation Feedback

www.ti.com 9B2 CMD Path CTRL (1) CTRL (1) CTRL (1) CTRL (1) 9B1 9DIR CS1 CTRL (1) (1) CTRL represents a decoded MODE0, MODE1, CS0, and CS1 state. (2) Translation point TP (2) TP (2) TP (2) TP (2) TP (2) TP (2) WP and R/B Paths (1) CTRL represents a decoded MODE0, MODE1, CS0, and CS1 state. (2) Translation point (3) 12A is open drain in NAND (XD) mode and push-pull in other modes. 11B11A CTRL (1) 12A 12B(3) TP (2) TP (2) SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Submit Documentation Feedback

www.ti.com 14B IRQ and CEout Paths CTRL (1) (1) CTRL represents a decoded MODE0, MODE1, CS0, and CS1 state. (2) Push-pull in NAND flash (XD) mode and open drain in other modes CTRL (1) CS0 (2) SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Submit Documentation Feedback

www.ti.com Absolute Maximum Ratings (1) SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT V CC Supply voltage range V CCA V CCB 0.5 4.6 V I/O ports port) 0.5 V CCA 0.5 V I Input voltage range (2) I/O ports port) 0.5 V CCB 0.5 V Control inputs 0.5 4.6 A port 0.5 V CCA 0.5 Voltage range applied to any output in the V O V high-impedance or power-off state (2) B port 0.5 V CCB 0.5 A port 0.5 V CCA 0.5 Voltage range applied to any output in the high or V O V low state (2) (3) B port 0.5 V CCB 0.5 I IK Input clamp current V I mA I OK Output clamp current V O mA I O Continuous output current mA Continuous current through V CCA V CCB or GND 100 mA θ JA Package thermal impedance (4) GQC/ZQC package C/W T stg Storage temperature range 150 C (1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. (2) The input voltage and output negative-voltage ratings may be exceeded if the input and output current ratings are observed. (3) The output positive-voltage rating may be exceeded up to 4.6 V maximum if the output current rating is observed. (4) The package thermal impedance is calculated in accordance with JESD 51-7. Submit Documentation Feedback

www.ti.com Recommended Operating Conditions (1) (2) (3) (4) SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 V CCI V CCO MIN MAX UNIT V CCA Supply voltage 1.4 V CCB V V CCB Supply voltage 1.4 3.6 V 1.4 V to 1.95 V V CCI 0.65 V IH High-level input voltage All inputs (5) 1.95 V to 2.7 V 1.7 V 2.7 V to 3.6 V 1.4 V to 1.95 V V CCI 0.35 V IL Low-level input voltage All inputs (5) 1.95 V to 2.7 V 0.7 V 2.7 V to 3.6 V 0.8 V I Input voltage V CCI V Active state V CCO V O Output voltage V 3-state V CCO 1.4 V to 1.6 V 1.65 V to 1.95 V I OH High-level output current port) mA 2.3 V to 2.7 V V to 3.6 V 1.4 V to 1.6 V 1.65 V to 1.95 V I OL Low-level output current port) mA 2.3 V to 2.7 V V to 3.6 V 1.4 V to 1.6 V 1.65 V to 1.95 V I OH High-level output current port) mA 2.3 V to 2.7 V V to 3.6 V 1.4 V to 1.6 V 1.65 V to 1.95 V I OL Low-level output current port) mA 2.3 V to 2.7 V V to 3.6 V Δ Δ t Input transition rise or fall rate ns/V T A Operating free-air temperature C (1) V CCI is the V CC associated with the data input port. (2) V CCO is the V CC associated with the output port. (3) V CCB must be greater than or equal to V CCA except when V CCB (4) All unused data inputs of the device must be held at V CCI or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs literature number SCBA004. (5) All A-port I/Os and control inputs are powered by V CCA 1B, 2B, 3B, 4B, 9B1, and 10B1 are powered by V CCB0 5B, 6B, 7B, 8B, 9B2, 10B2, 11B, 12B, and 14B are powered by V CCB1 Submit Documentation Feedback

www.ti.com Electrical Characteristics (1) (2) SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS V CCA V CCB MIN TYP (3) MAX UNIT I OH 100 µ A 1.4 V to 3.6 V 1.4 V to 3.6 V V CCO 0.2 I OH mA 1.4 V 1.4 V 1.05 V OH port) I OH mA V I V IH 1.65 V 1.65 V 1.2 V I OH mA 2.3 V 2.3 V 1.75 I OH mA V V 2.3 I OL 100 µ A 1.4 V to 3.6 V 1.4 V to 3.6 V 0.2 I OL mA 1.4 V 1.4 V 0.35 I OL mA V I V IL 1.65 V 1.65 V 0.45 V OL port) V I OL mA 2.3 V 2.3 V 0.55 I OL mA V V 0.7 I OL mA Open-drain output (12A) V V 0.45 I OH 100 µ A 1.4 V to 3.6 V 1.4 V to 3.6 V V CCO 0.2 I OH mA 1.4 V 1.4 V 1.05 V OH port) I OH mA V I V IH 1.65 V 1.65 V 1.2 V I OH mA 2.3 V 2.3 V 1.75 I OH mA V V 2.3 I OL 100 µ A 1.4 V to 3.6 V 1.4 V to 3.6 V 0.2 I OL mA 1.4 V 1.4 V 0.35 I OL mA V I V IL 1.65 V 1.65 V 0.45 V OL port) V I OL mA 2.3 V 2.3 V 0.55 I OL mA V V 0.7 I OL mA Open-drain output (14B) V V 0.45 I I Control inputs V I V CCA or GND 1.4 V to 3.6 V 3.6 V 2.5 µ A I off 14B V O V CCA to 3.6 V V µ A A or B ports V O V CCO or See function table for 3.6 V 3.6 V I OZ (4) GND, input states when µ A A port 3.6 V V V I V IH or V IL outputs are Hi Z 1.6 V 1.6 V 4.5 1.95 V 1.95 V 1.95 V V I CCA V I V CCI or GND, I O µ A 2.7 V 2.7 V 5.5 3.6 V V 3.6 V 3.6 V 1.6 V 1.6 V 6.5 1.95 V 1.95 V 1.95 V V 0.5 I CCB V I V CCI or GND, I O µ A 2.7 V 2.7 V 7.5 3.6 V V 3.6 V 3.6 V (1) V CCO is the V CC associated with the output port. (2) V CCI is the V CC associated with the data input port. (3) All typical values are at T A (4) For I/O ports, the parameter I OZ includes the input leakage current. Submit Documentation Feedback

www.ti.com Output Slew Rates (1) SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Electrical Characteristics (continued) over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS V CCA V CCB MIN TYP (3) MAX UNIT Control inputs 3.5 C i V I V CCA or GND 1.8 V V pF Clock input C o 14B V O V CCB or GND 1.8 V V 17.5 pF A port V O V CCA or GND 4.5 C io 1.8 V V pF B port V O V CCB or GND over recommended operating free-air temperature range (unless otherwise noted) V CCA 1.8 V 0.15 V CCB V PARAMETER FROM TO UNIT 0.3 V MIN MAX t r 10% 90% (2) ns t f 90% 10% (2) ns (1) Values are characterized, but not production tested. (2) Using C L pF on the B side and C L pF on the A side. See derating curves for other load conditions. Submit Documentation Feedback

www.ti.com Switching Characteristics Maximum Frequency and Output Skew SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 V CCA 1.5 V 0.1 over recommended operating free-air temperature range (see Figure V CCB 1.8 V V CCB 2.5 V V CCB V V CCB 3.3 V FROM TO 0.15 V 0.2 V 0.3 V 0.3 V PARAMETER UNIT (INPUT) (OUTPUT) MIN MAX MIN MAX MIN MAX MIN MAX A B 7.7 4.9 4.7 4.4 B A 6.3 CLK.h or SCLK.h CLK.0 or SCLK.0 7.7 4.9 4.9 CLK.h or SCLK.h CLK-f.h or SCLK-f.h 9.7 CMD.h CMD.0 7.1 4.1 3.9 3.6 t pd CMD.h CMD.1 4.6 4.1 4.2 ns CMD.0 CMD.h 6.2 4.9 4.8 4.7 CS0 B 4.2 4.2 3.9 R/B R/B.h 5.7 4.8 4.7 4.8 WE WE 7.4 4.3 4.3 4.2 WP WP 6.6 4.5 4.4 4.3 DAT1.0 or DATA1.0 IRQ 4.8 3.3 3.3 3.3 DAT1.1 or DATA1.1 IRQ 4.9 3.4 3.3 3.3 t en DIR B 6.7 4.5 4.4 4.6 ns DIR A 10.3 9.6 9.6 9.5 R/B R/B.h (open drain) 5.9 5.4 5.4 5.4 DAT1.0 or DATA1.0 IRQ 6.7 4.9 5.5 5.5 DAT1.1 or DATA1.1 IRQ 6.5 4.7 5.4 5.4 t dis DIR B 6.9 6.4 6.4 6.3 ns DIR A 5.3 5.3 5.3 5.2 R/B R/B.h (open drain) 16.9 17.4 5.3 4.1 V CCA 1.5 V 0.1 over recommended operating free-air temperature range (see Figure V CCB V V CCB 3.3 V FROM TO 0.3 V 0.3 V PARAMETER UNIT (INPUT) (OUTPUT) MIN MAX MIN MAX A B Clock B A f max MHz A B Data B A t sk(o) A B 1.5 1.5 ns Submit Documentation Feedback

www.ti.com Switching Characteristics Maximum Frequency and Output Skew SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 V CCA 1.8 V 0.15 over recommended operating free-air temperature range (see Figure V CCB 1.8 V V CCB 2.5 V V CCB V V CCB 3.3 V FROM TO 0.15 V 0.2 V 0.3 V 0.3 V PARAMETER UNIT (INPUT) (OUTPUT) MIN MAX MIN MAX MIN MAX MIN MAX A B 7.5 4.6 4.1 3.7 B A 4.6 4.2 4.1 CLK.h or SCLK.h CLK.0 or SCLK.0 4.8 4.3 4.2 CLK.h or SCLK.h CLK-f.h or SCLK-f.h 17.9 9.4 8.7 8.3 CMD.h CMD.0 7.4 3.7 3.3 3.3 t pd CMD.h CMD.1 6.2 4.4 3.7 3.5 ns CMD.0 CMD.h 4.5 3.8 3.8 CS0 B 6.6 3.8 R/B R/B.h 4.4 3.8 3.8 WE WE 7.3 3.9 3.8 3.7 WP WP 5.6 3.6 3.8 DAT1.0 or DATA1.0 IRQ 3.3 3.3 3.3 DAT1.1 or DATA1.1 IRQ 4.6 3.1 3.1 3.1 t en DIR B 6.4 3.8 3.6 3.6 ns DIR A 7.7 6.9 6.9 6.9 R/B R/B.h (open drain) 4.4 4.1 4.1 4.1 DAT1.0 or DATA1.0 IRQ 6.5 4.8 5.5 5.5 DAT1.1 or DATA1.1 IRQ 6.6 4.8 5.3 5.3 t dis DIR B 6.3 5.4 5.7 5.7 ns DIR A 5.2 5.3 5.2 5.2 R/B R/B.h (open drain) 15.9 19.5 5.6 3.8 V CCA 1.8 V 0.15 over recommended operating free-air temperature range (see Figure V CCB V V CCB 3.3 V FROM TO 0.3 V 0.3 V PARAMETER UNIT (INPUT) (OUTPUT) MIN MAX MIN MAX A B Clock B A f max MHz A B Data B A t sk(o) A B 0.8 0.8 ns Submit Documentation Feedback

www.ti.com Switching Characteristics Maximum Frequency and Output Skew SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 V CCA 2.5 V 0.2 over recommended operating free-air temperature range (see Figure V CCB 2.5 V V CCB V V CCB 3.3 V FROM TO 0.2 V 0.3 V 0.3 V PARAMETER UNIT (INPUT) (OUTPUT) MIN MAX MIN MAX MIN MAX A B 3.4 3.1 B A 3.7 3.5 3.6 CLK.h or SCLK.h CLK.0 or SCLK.0 3.9 3.5 3.5 CLK.h or SCLK.h CLK-f.h or SCLK-f.h 8.3 7.3 CMD.h CMD.0 3.2 3.1 2.7 t pd CMD.h CMD.1 3.6 2.8 ns CMD.0 CMD.h CS0 B 4.2 3.7 3.3 R/B R/B.h 3.1 2.9 WE WE 3.6 3.4 WP WP 3.5 3.1 2.9 DAT1.0 or DATA1.0 IRQ 3.3 3.3 3.2 DAT1.1 or DATA1.1 IRQ 3.6 3.4 3.2 t en DIR B 4.7 4.4 3.6 ns DIR A 5.3 5.3 5.1 R/B R/B.h (open drain) 3.2 3.1 DAT1.0 or DATA1.0 IRQ 7.2 5.4 5.4 DAT1.1 or DATA1.1 IRQ 5.4 5.4 t dis DIR B 4.5 5.1 5.1 ns DIR A 3.7 3.7 3.7 R/B R/B.h (open drain) 3.2 3.9 3.9 V CCA 2.5 V 0.2 over recommended operating free-air temperature range (see Figure V CCB V V CCB 3.3 V FROM TO 0.3 V 0.3 V PARAMETER UNIT (INPUT) (OUTPUT) MIN MAX MIN MAX A B Clock B A f max MHz A B Data B A t sk(o) A B 0.7 0.7 ns Submit Documentation Feedback

www.ti.com Switching Characteristics Maximum Frequency and Output Skew SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 V CCA 3.3 V 0.3 over recommended operating free-air temperature range (see Figure V CCB 3.3 V FROM TO 0.3 V PARAMETER UNIT (INPUT) (OUTPUT) MIN MAX A B 2.9 B A 3.8 CLK.h or SCLK.h CLK.0 or SCLK.0 3.3 CLK.h or SCLK.h CLK-f.h or SCLK-f.h 6.1 CMD.h CMD.0 2.7 t pd CMD.h CMD.1 2.7 ns CMD.0 CMD.h 2.6 CS0 B 3.7 R/B R/B.h 2.5 WE WE WP WP 2.8 DAT1.0 or DATA1.0 IRQ 3.2 DAT1.1 or DATA1.1 IRQ 3.2 t en DIR B 3.7 ns DIR A 4.7 R/B R/B.h (open drain) 4.9 DAT1.0 or DATA1.0 IRQ 5.3 DAT1.1 or DATA1.1 IRQ 5.2 t dis DIR B ns DIR A 4.7 R/B R/B.h (open drain) V CCA 3.3 V 0.3 over recommended operating free-air temperature range (see Figure V CCB 3.3 V FROM TO 0.3 V PARAMETER UNIT (INPUT) (OUTPUT) MIN MAX A B Clock B A f max MHz A B Data B A t sk(o) A B 0.7 ns Submit Documentation Feedback

www.ti.com Operating Characteristics SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 V CCA 1.8 V CCB T A C PARAMETER TEST CONDITIONS TYP UNIT Outputs enabled Power dissipation capacitance per transceiver, A-port input, B-port output Outputs disabled 0.1 C pdA C L f MHz pF Outputs enabled Power dissipation capacitance per transceiver, B-port input, A-port output Outputs disabled 7.5 Outputs enabled 16.5 Power dissipation capacitance per transceiver, A-port input, B-port output Outputs disabled 0.1 C pdB0 C L f MHz pF Outputs enabled Power dissipation capacitance per transceiver, B-port input, A-port output Outputs disabled Outputs enabled Power dissipation capacitance per transceiver, A-port input, B-port output Outputs disabled 0.1 C pdB1 C L f MHz pF Outputs enabled Power dissipation capacitance per transceiver, B-port input, A-port output Outputs disabled Submit Documentation Feedback

www.ti.com PARAMETER MEASUREMENT INFORMATION VOH VOL From Output /charBnZrBnZrBnZrBnZrBnZrBnZrBnZrBnZrUnder Test C L (see Note A) LOAD CIRCUIT 2 × VCCO Open GND R L R L tPLH tPHL Output Control (low-level enabling) Output W aveform 1 S1 at 2 × VCCO (see Note B) Output W aveform 2 S1 at GND (see Note B) tPZL tPZH tPLZ tPHZ VCCA /2VCCA /2 VCCI/2 V CCI/2 VCCI 0 V VCCO /2 V CCO /2 VOH VOL 0 V VCCO /2 VOL + VTP VCCO /2 VOH − VTP 0 V Input VCCA VCCO VOLT AGE W AVEFORMS PROPAGA TION DELA Y TIMES VOLT AGE W AVEFORMS ENABLE AND DISABLE TIMES Output tpd tPLZ /tPZL tPHZ /tPZH tPLZ /tPZL (OD) Open 2 × VCCO GND 2 × VCCO TEST S1 NOTES: A. C L includes probe and jig capacitance. B. W aveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR/C011810 MHz, ZO = 50 W , dv/dt ≥/charBnZrBnZrBnZrBnZrBnZrBnZrBnZrBnZr1 V/ns. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. V CCI is the VCC associated with the input port. I. VCCO is the VCC associated with the output port. 1.5 V ± 0.1 V 1.8 V ± 0.15 V 2.5 V ± 0.2 V 3.3 V ± 0.3 V 2 kW 2 kW 2 kW 2 kW VCCO R L 0.1 V 0.15 V 0.15 V 0.3 V VTP C L 15 pF 15 pF 15 pF 15 pF SN74AVCA406 MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER SCES615H OCTOBER 2004 REVISED JANUARY 2007 Figure Load Circuit and Voltage Waveforms Submit Documentation Feedback

www.ti.com 20-Aug-2011 Addendum-Page 1 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) SN74AVCA406DGGR ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVCA406DGGRE4 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVCA406DGGRG4 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVCA406ZQCR ACTIVE BGA MICROSTAR JUNIOR ZQC 48 2500 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

*All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant SN74AVCA406ZQCR BGA MI CROSTA R JUNI OR PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 Pack Materials-Page 1

*All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74AVCA406DGGR TSSOP DGG 48 2000 367.0 367.0 45.0 SN74AVCA406ZQCR BGA MICROSTAR JUNIOR ZQC 48 2500 340.5 338.1 20.6 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 Pack Materials-Page 2

MTSS003D – JANUARY 1995 – REVISED JANUARY 1998 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 4040078/F 12/97

48 PINS SHOWN

0,25 0,15 NOM Gage Plane 6,00 6,20 8,30 7,90 0,75 0,50 Seating Plane 0,27 0,17 A 1,20 MAX M0,08 0,10 0,50 0°–8° 14,10 13,90 48DIM A MAX A MIN PINS ** 12,40 12,60 17,10 16,90 0,15 0,05 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Body dimensions do not include mold protrusion not to exceed 0,15. D. Falls within JEDEC MO-153

Texas InstrumentsIncorporatedand itssubsidiaries(TI)reservetherighttomake corrections,enhancements,improvementsand other changes toitssemiconductorproductsand servicesperJESD46C and todiscontinueany productorserviceperJESD48B. Buyersshould obtainthelatestrelevantinformationbeforeplacingordersand shouldverifythatsuch informationiscurrentand complete.All semiconductorproducts(alsoreferredtohereinas “components”)aresoldsubjecttoTI’s termsand conditionsofsalesuppliedatthetime oforderacknowledgment. TIwarrantsperformanceofitscomponents tothespecificationsapplicableatthetimeofsale,inaccordancewiththewarrantyinTI’s terms and conditionsofsaleofsemiconductorproducts.Testingand otherqualitycontroltechniquesareused totheextentTIdeems necessary tosupportthiswarranty.Exceptwhere mandated by applicablelaw,testingofallparametersofeach component isnotnecessarily performed. TIassumes no liabilityforapplicationsassistanceorthedesignofBuyers’products.Buyersareresponsiblefortheirproductsand applicationsusingTIcomponents.To minimizetherisksassociatedwithBuyers’productsand applications,Buyersshouldprovide adequatedesignand operatingsafeguards. TIdoes notwarrantorrepresentthatany license,eitherexpressorimplied,isgrantedunderany patentright,copyright,mask work right,or otherintellectualpropertyrightrelatingtoany combination,machine,orprocessinwhichTIcomponents orservicesareused.Information publishedby TIregardingthird-partyproductsorservicesdoes notconstitutea licensetouse such productsorservicesora warrantyor endorsementthereof.Use ofsuch informationmay requirea licensefroma thirdpartyunderthepatentsorotherintellectualpropertyofthe thirdparty,ora licensefromTIunderthepatentsorotherintellectualpropertyofTI. ReproductionofsignificantportionsofTIinformationinTIdatabooks ordatasheetsispermissibleonlyifreproductioniswithoutalteration and isaccompaniedby allassociatedwarranties,conditions,limitations,and notices.TIisnotresponsibleorliableforsuch altered documentation.Informationofthirdpartiesmay be subjecttoadditionalrestrictions. ResaleofTIcomponents orserviceswithstatementsdifferentfromorbeyond theparametersstatedby TIforthatcomponent orservice voidsallexpressand any impliedwarrantiesfortheassociatedTIcomponent orserviceand isan unfairand deceptivebusinesspractice. TIisnotresponsibleorliableforany such statements. Buyeracknowledgesand agreesthatitissolelyresponsibleforcompliancewithalllegal,regulatoryand safety-relatedrequirements concerningitsproducts,and any use ofTIcomponents initsapplications,notwithstandingany applications-relatedinformationorsupport thatmay be providedby TI.Buyerrepresentsand agreesthatithas allthenecessaryexpertisetocreateand implementsafeguardswhich anticipatedangerousconsequencesoffailures,monitorfailuresand theirconsequences,lessenthelikelihoodoffailuresthatmightcause harm and takeappropriateremedialactions.BuyerwillfullyindemnifyTIand itsrepresentativesagainstany damages arisingoutoftheuse ofany TIcomponents insafety-criticalapplications. Insome cases,TIcomponents may be promotedspecificallytofacilitatesafety-relatedapplications.Withsuch components,TI’s goalisto helpenablecustomerstodesignand createtheirown end-productsolutionsthatmeet applicablefunctionalsafetystandardsand requirements.Nonetheless,such components aresubjecttotheseterms. No TIcomponents areauthorizedforuse inFDA ClassIII(orsimilarlife-criticalmedicalequipment)unlessauthorizedofficersoftheparties have executeda specialagreementspecificallygoverningsuch use. OnlythoseTIcomponents whichTIhas specificallydesignatedas militarygradeor“enhanced plastic”aredesignedand intendedforuse in military/aerospaceapplicationsorenvironments.Buyeracknowledgesand agreesthatany militaryoraerospaceuse ofTIcomponents whichhave not been so designatedissolelyattheBuyer's risk,and thatBuyerissolelyresponsibleforcompliancewithalllegaland regulatoryrequirementsinconnectionwithsuch use. TIhas specificallydesignatedcertaincomponents whichmeet ISO/TS16949 requirements,mainlyforautomotiveuse.Components which have notbeen so designatedareneitherdesignednorintendedforautomotiveuse;and TIwillnotbe responsibleforany failureofsuch components tomeet such requirements. Products Applications Audio www.ti.com/audio Automotiveand Transportationwww.ti.com/automotive Amplifiers amplifier.ti.com Communicationsand Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP ® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energyand Lighting www.ti.com/energy Clocksand Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space,Avionicsand Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Videoand Imaging www.ti.com/video RFID www.ti-rfid.com OMAP MobileProcessors www.ti.com/omap TIE2E Community e2e.ti.com WirelessConnectivity www.ti.com/wirelessconnectivity MailingAddress:Texas Instruments,PostOfficeBox 655303,Dallas,Texas 75265 Copyright© 2012,Texas InstrumentsIncorporated

Summary

MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 짹15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER

Description

MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card 짹15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER

Source title AVCE6467T Datasheet(PDF) - Texas Instruments

Read AVCE6467T online.