ATV312

ATV312H018M2412 SCHNEIDER | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 3

Technical content

variable speed drive ATV312 - 0.18kW - 0.6kVA - 24W - 200..240 V- 1-phase supply Main Range of product Altivar 312 Solar Product or component type Variable speed drive Product destination Asynchronous motors Product specific application Pumping station with photovoltaic arrays Assembly style With heat sink Device short name ATV312 Complementary Motor power kW 0.18 kW Motor power hp 0.25 hp Supply voltage limits 170…264 V Network frequency 47.5...63 Hz Network number of phases Single phase Line current 3 A at 200 V, Isc = 1 kA

2.5 A at 240 V

Apparent power 0.6 kVA Prospective line Isc 1 kA Continuous output current 1.5 A at 4 kHz Maximum transient current 2.3 A for 60 s Power dissipation in W 24 W at nominal load Speed drive output frequency 0.5…500 Hz Nominal switching frequency 4 kHz Switching frequency 2...16 kHz adjustable Speed range 1…50 Transient overtorque 150…170 % of nominal motor torque Braking torque <= 150 % during 60 s with braking resistor 100 % with braking resistor continuously 150 % without braking resistor Disclaimer: This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications May 18, 2021

Asynchronous motor control profile Factory set: energy saving mode Regulation loop Frequency PI regulator Motor slip compensation Automatic whatever the load Adjustable Suppressable Output voltage <= power supply voltage L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 2.5 mm² AWG 14 L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-: 0.8 N.m Insulation Electrical between power and control Supply Internal supply for logic inputs at 19...30 V, <100 A, protection type: overload and short-circuit protection overload and short-circuit protection Analogue input number 3 Analogue input type AI1 configurable voltage 0...10 V, input voltage 30 V max, impedance: 30000 Ohm AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance: 30000 Ohm AI3 configurable current 0...20 mA, impedance: 250 Ohm Sampling duration AI1, AI2, AI3: 8 ms analog LI1...LI6: 4 ms discrete Response time AOV, AOC 8 ms for analog R1A, R1B, R1C, R2A, R2B 8 ms for discrete Linearity error +/- 0.2 % for output Analogue output number 2 Analogue output type AOC configurable current: 0...20 mA, impedance: 800 Ohm, resolution: 8 bits AOV configurable voltage: 0...10 V, impedance: 470 Ohm, resolution: 8 bits Discrete input logic Logic input not wired (LI1...LI4), < 13 V (state 1) Negative logic (source) (LI1...LI6), > 19 V (state 0) Positive logic (source) (LI1...LI6), < 5 V (state 0), > 11 V (state 1) Discrete output number 2 Discrete output type Configurable relay logic: (R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles Configurable relay logic: (R2A, R2B) NC - 100000 cycles Minimum switching current R1-R2 10 mA at 5 V DC Maximum switching current 2 A at 250 V AC on inductive load - cos phi = 0.4 - L/R = 7 ms (R1-R2) 2 A at 30 V DC on inductive load - cos phi = 0.4 - L/R = 7 ms (R1-R2)

5 A at 250 V AC on resistive load - cos phi = 1 - L/R = 0 ms (R1-R2)

5 A at 30 V DC on resistive load - cos phi = 1 - L/R = 0 ms (R1-R2)

Discrete input type (LI1...LI6) programmable at 24 V, 0…100 mA for PLC, impedance: 3500 Ohm Acceleration and deceleration ramps Linear adjustable separately from 0.1 to 999.9 s S, U or customized Braking to standstill By DC injection Protection type Input phase breaks: drive Line supply overvoltage and undervoltage safety circuits: drive Line supply phase loss safety function, for three phases supply: drive Motor phase breaks: drive Overcurrent between output phases and earth (on power up only): drive Overheating protection: drive Short-circuit between motor phases: drive Thermal protection: motor Dielectric strength 2040 V DC between earth and power terminals

2880 V AC between control and power terminals

Insulation resistance >= 500 mOhm 500 V DC for 1 minute Local signalling 1 LED (red) for drive voltage Four 7-segment display units for CANopen bus status Time constant 5 ms for reference change Frequency resolution Analog input: 0.1...100 Hz Display unit: 0.1 Hz Communication port protocol CANopen Modbus Connector type 1 RJ45 for Modbus/CANopen

Physical interface RS485 multidrop serial link Transmission frame RTU Transmission rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps for CANopen 4800, 9600 or 19200 bps for Modbus Number of addresses 1…127 for CANopen 1…247 for Modbus Number of drive 127 for CANopen 31 for Modbus Electromagnetic compatibility 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5 Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4 Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2 Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3 Standards IEC 61800-5-1 Marking CE Height 145 mm Width 72 mm Depth 132 mm Net weight 1.5 kg Option card Communication card for CANopen daisy chain Communication card for DeviceNet Communication card for Fipio Communication card for Modbus TCP Communication card for Profibus DP Environment IP degree of protection IP20 without cover plate Pollution degree 2 Protective treatment TC Vibration resistance 1 gn (f= 13…150 Hz) conforming to EN/IEC 60068-2-6 1.5 mm (f= 3…13 Hz) conforming to EN/IEC 60068-2-6 Shock resistance 15 gn for 11 ms conforming to EN/IEC 60068-2-27 Relative humidity 5…95 % without condensation conforming to IEC 60068-2-3 5…95 % without dripping water conforming to IEC 60068-2-3 Ambient air temperature for storage -25…70 °C Ambient air temperature for operation -10…50 °C without derating (with protective cover on top of the drive) -10…60 °C with derating factor (without protective cover on top of the drive) Operating altitude <= 1000 m without derating >= 1000 m with current derating 1 % per 100 m Operating position Vertical +/- 10 degree Packing Units Unit Type of Package 1 PCE Number of Units in Package 1 1 Package 1 Weight 1.4 kg Package 1 Height 13.5 cm Package 1 width 17.5 cm Package 1 Length 18 cm Contractual warranty Warranty 18 months