ATV12H055M2TQ SCHNEIDER | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 10
Technical content
variable speed driveATV12 -0.55kW -0.75hp -200..240V -1ph -w heat sink-lot of 14 Main Range of product Altivar 12 Product or component type Variable speed drive Product destination Asynchronous motors Product specific application Simple machine Assembly style With heat sink Component name ATV12 Quantity per set Set of 14 EMC filter Integrated Built-in fan Without Network number of phases 1 phase Motor power kW 0.55 kW Motor power hp 0.75 hp Communication port protocol Modbus Line current 8 A at 200 V
6.7 A at 240 V
Speed range 1…20 Transient overtorque 150…170 % of nominal motor torque depending on drive rating and type of motor Asynchronous motor control profile Sensorless flux vector control Quadratic voltage/frequency ratio Voltage/frequency ratio (V/f) IP degree of protection IP20 without blanking plate on upper part Noise level 0 dB Complementary Supply frequency 50/60 Hz +/- 5 % Connector type 1 RJ45 (on front face) for Modbus Disclaimer: This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications May 14, 2021
Physical interface 2-wire RS 485 for Modbus Transmission frame RTU for Modbus Transmission rate 4800 bit/s 9600 bit/s 19200 bit/s 38400 bit/s Number of addresses 1…247 for Modbus Communication service Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/write multiple registers (23) 4/4 words Read device identification (43) Prospective line Isc 1 kA Continuous output current 3.5 A at 4 kHz Maximum transient current 5.3 A for 60 s Speed drive output frequency 0.5…400 Hz Nominal switching frequency 4 kHz Switching frequency 2...16 kHz adjustable 4...16 kHz with derating factor Braking torque Up to 70 % of nominal motor torque without braking resistor Motor slip compensation Adjustable Preset in factory Output voltage 200...240 V 3 phases Electrical connection Terminal, clamping capacity: 3.5 mm², AWG 12 (L1, L2, L3, U, V, W, PA, PC) Tightening torque 0.8 N.m Insulation Electrical between power and control Supply Internal supply for reference potentiometer: 5 V DC (4.75…5.25 V), <10 mA, protection type: overload and short-circuit protection Internal supply for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, protection type: overload and short-circuit protection Analogue input number 1 Analogue input type Configurable current AI1 0...20 mA 250 Ohm Configurable voltage AI1 0...10 V 30 kOhm Configurable voltage AI1 0...5 V 30 kOhm Discrete input number 4 Discrete input logic Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm Positive logic (source), 0...< 5 V (state 0), > 11 V (state 1) Sampling duration 20 ms, tolerance +/- 1 ms for logic input 10 ms for analogue input Linearity error +/- 0.3 % of maximum value for analogue input Analogue output number 1 Analogue output type AO1 software-configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bits AO1 software-configurable current: 0...20 mA, impedance: 800 Ohm, resolution 8 bits Discrete output number 2 Discrete output type Logic output LO+, LO- Protected relay output R1A, R1B, R1C 1 C/O Minimum switching current 5 mA at 24 V DC for logic relay Maximum switching current 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay
3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay
4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
Acceleration and deceleration ramps U S Linear from 0 to 999.9 s Braking to standstill By DC injection, <30 s Protection type Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases
Against input phase loss in three-phase Thermal motor protection via the drive by continuous calculation of I²t Frequency resolution Analog input: converter A/D, 10 bits Display unit: 0.1 Hz Time constant 20 ms +/- 1 ms for reference change Marking CE Operating position Vertical +/- 10 degree Height 143 mm Width 72 mm Depth 131.2 mm Net weight 0.8 kg Variable speed drive application selection Commercial equipment Mixer Commercial equipment Other application Textile Ironing Motor starter type Variable speed drive Environment Electromagnetic compatibility Electrical fast transient/burst immunity test level 4 conforming to EN/IEC 61000-4-4 Electrostatic discharge immunity test level 3 conforming to EN/IEC 61000-4-2 Immunity to conducted disturbances level 3 conforming to EN/IEC 61000-4-6 Radiated radio-frequency electromagnetic field immunity test level 3 conforming to EN/IEC 61000-4-3 Surge immunity test level 3 conforming to EN/IEC 61000-4-5 Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11 Electromagnetic emission Radiated emissions environment 1 category C2 conforming to EN/IEC 61800-3 2...16 kHz shielded motor cable Conducted emissions with integrated EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable <5 m Conducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 2...12 kHz shielded motor cable <5 m Conducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 2, 4 and 16 kHz shielded motor cable <10 m Conducted emissions with additional EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <20 m Conducted emissions with additional EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <50 m Conducted emissions with additional EMC filter environment 2 category C3 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <50 m Product certifications GOST C-Tick NOM CSA UL Vibration resistance 1 gn (f = 13…200 Hz) conforming to EN/IEC 60068-2-6 1.5 mm peak to peak (f = 3…13 Hz) - drive unmounted on symmetrical DIN rail - conforming to EN/ IEC 60068-2-6 Shock resistance 15 gn conforming to EN/IEC 60068-2-27 for 11 ms Relative humidity 5…95 % without condensation conforming to IEC 60068-2-3 5…95 % without dripping water conforming to IEC 60068-2-3 Ambient air temperature for storage -25…70 °C Ambient air temperature for operation -10…40 °C protective cover from the top of the drive removed 40…60 °C with current derating 2.2 % per °C Operating altitude > 1000...2000 m with current derating 1 % per 100 m <= 1000 m without derating Packing Units Unit Type of Package 1 PCE Number of Units in Package 1 1 Package 1 Weight 1.042 kg Package 1 Height 20 cm Package 1 width 40 cm Package 1 Length 60 cm Unit Type of Package 2 BB1
Number of Units in Package 2 14 Package 2 Weight 14.688 kg Package 2 Height 20 cm Package 2 width 40 cm Package 2 Length 60 cm Unit Type of Package 3 P06 Number of Units in Package 3 84 Package 3 Weight 96.088 kg Package 3 Height 80 cm Package 3 width 80 cm Package 3 Length 60 cm Offer Sustainability Sustainable offer status Green Premium product REACh Regulation REACh Declaration EU RoHS Directive Pro-active compliance (Product out of EU RoHS legal scope) EU RoHS Declaration Mercury free Yes RoHS exemption information Yes China RoHS Regulation China RoHS declaration Environmental Disclosure Product Environmental Profile Circularity Profile End of Life Information WEEE The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins California proposition 65 WARNING: This product can expose you to chemicals including: Lead and lead compounds, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Drive without EMC Conformity Kit Dimensions in mm b c H 130 131.2 120 Dimensions in in. b c H 5.12 5.16 4.72 Drive with EMC Conformity Kit Dimensions in mm Dimensions in in. 2.48
Clearance for Vertical Mounting Mounting Type A Mounting Type B Remove the protective cover from the top of the drive. Mounting Type C Remove the protective cover from the top of the drive.
Single-Phase Power Supply Wiring Diagram A1 Drive KM1 Contactor (only if a control circuit is needed) P1 2.2 kΩ reference potentiometer. This can be replaced by a 10 kΩ potentiometer (maximum). Q1 Circuit breaker (1) Negative logic (Sink) (2) Positive logic (Source) (factory set configuration)
2-Wire Control for Logic I/O with Internal Power Supply LI1 : Forward LI• : Reverse A1 : Drive 3-Wire Control for Logic I/O with Internal Power Supply LI1 : Stop LI2 : Forward LI• : Reverse A1 : Drive Analog Input Configured for Voltage with Internal Power Supply (1) 2.2 kΩ…10 kΩ reference potentiometer A1 : Drive Analog Input Configured for Current with Internal Power Supply (2) 0-20 mA 4-20 mA supply A1 : Drive
Connected as Positive Logic (Source) with External 24 vdc Supply (1) 24 vdc supply A1 : Drive Connected as Negative Logic (Sink) with External 24 vdc supply (1) 24 vdc supply A1 : Drive
1 : Self-cooled motor: continuous useful torque (1) 2 : Force-cooled motor: continuous useful torque 3 : Transient overtorque for 60 s 4 : Transient overtorque for 2 s 5 : Torque in overspeed at constant power (2) (1) For power ratings ≤ 250 W, derating is 20% instead of 50% at very low frequencies. (2) The nominal motor frequency and the maximum output frequency can be adjusted from 0.5 to 400 Hz. The mechanical overspeed capability of the selected motor must be checked with the manufacturer.