ATPGGBL5R2580A YIC | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 12
Technical content
Yuechung International Corp. URL: www.yic.com.tw E-mail: service@yic.com.tw GPS L1 / L5 (IRNSS) & Glonass & BDS Patch Antenna
1 SCOPE
This specification covers the dielectric Patch antenna for L1+L5+Galileo+Glonass+Beidou. 2 PART NO.：ATPGGBL5R2580A
3 OUTLINE DRAWING AND DIMENSIONS
3.1 Appearance: No visible damage and dirt. 3.2 The products conform to the RoHS directive and national environment protection law.
3.3 Pictures and Dimensions:
Yuechung International Corp. (YIC) 1 YYIICC 4. ELECTRICAL SPECIFICATIONS
4.1 Performance Characteristics
Range Of Receiving Frequency L1：1575.42±1.023MHz L5：1176.45± 12MHz Galileo：1577± 14MHz Glonass：1602±5MHz Beidou：1561.098±2.046 MHz Center Frequency L1：1572±3MHz L5：1174±3MHz L1：With 64.76× 37.64 mm GND Plane L5：With 65.36× 70.88 mm GND Plane Bandwidth L1：22MHz min L5：3MHz min Return Loss@-10dB VSWR 1.8 max Center Frequency Gain at Zenith L1：0.6dBi L5：0.5dBi Galileo：0.6dBi Glonass：3.4dBi Beidou：2.4dBi Customer Prototype Axial Ratio - - -
7 Polarization RHCP
Right Hand Circular Polarization Impedance
50 Ohm
9 Frequency Temperature Coefficient（τf） -40°C to +105°C 0 ± 20ppm / ℃
-40°C to +105°C ※ Please follow the Golden Sample characteristics and compensation the instrument measurement value when IQC Inspection.
Yuechung International Corp. (YIC) 2 YYIICC 5. Typical Electrical Characteristics（T=25℃） Return Loss, SWR, Impedance, measured on the test fixture
Yuechung International Corp. (YIC) 3 YYIICC Patch 25x25 ,18x18 on L1+L5+Galileo+GLONASS+BEIDOU S11 Return Loss & Smith Chart Measure.
Yuechung International Corp. (YIC) 4 YYIICC 6. 2D Radiation Pattern XZ+YZ -Plane 1176 MHz
Yuechung International Corp. (YIC) 5 YYIICC XZ+YZ -Plane 1561 MHz XZ -1.5 1.40 2.96 YZ -2.37 1.05 2.85
Yuechung International Corp. (YIC) 6 YYIICC XZ+YZ -Plane 1575.42 MHz
Yuechung International Corp. (YIC) 7 YYIICC XZ+YZ -Plane 1602 MHz XZ -1.7 1.89 3.93
Yuechung International Corp. (YIC) 8 YYIICC 7. Tape Dimension 18x18 25x25
Yuechung International Corp. (YIC) 9 YYIICC 8. Test Fixture for Antenna Setup & Measurements
Yuechung International Corp. (YIC) 10 YYIICC 9. Characteristics and Reliability Test Test Items Test Condition and Procedure Requirements C1 S.W.R. Set DUT on Network Analyzer; make individual calibration to test Directive DUT specification C2 Antenna Gain Set DUT on Antenna Chamber; make individual calibration to test Directive DUT specification M1 Vibration MIL-STD-202G, 201A Amplitude: 0.03 inch (0.76mm); Freq: 10 to 55 Hz 3 directions; 2 hours for each direction 1. No Visual Damage 2. Frequency Tol.<= 5% M2 Random Drop Height: 1.5 Meter; 3 directions; 1 time for each direction 1. No parts separated 2. Frequency Tol.<= 5% M3 Solderability MIL-STD-202G, 210F, cond. A Solder iron: 350±10°C; Duration: 5 seconds 1. Mounted on PCB 2. No Visual Damage M4 Terminal- Pull Test MIL-STD-202G, 211A, cond. A Holding with individual specification; force applied to axis of terminal 1. Directive DUT specification 2. Frequency Tol.<= 5% M5 Terminal- Torque Test MIL-STD-202G, 211A, cond. E Holding with individual specification; applied clockwise and counterclockwise to the axis of terminal 1. Directive DUT specification 2. Frequency Tol.<= 5% M6 Dimension Inspection of dimension, color, material, package, surface process Directive DUT specification E1 Salt Spray MIL-STD-202G, 101E, cond. B Temp: 35°C; RH: >= 95%; NaCl solution: >= 5%; Time: 48 hours After 2 Hours Recovery 1. No Visual Damage 2. Frequency Tol.<= 5% E2 Humidity MIL-STD-202G, 103B, cond. B Temp: 40°C; RH: >= 95%; Time: 48 hours After 2 Hours Recovery 1. No Visual Damage 2. Frequency Tol.<= 5% E3 Thermal Shock
1 Cycle: - 40°C (30 minutes) to + 80°C (30 minutes)
Cycles: 24 After 2 Hours Recovery 1. No Visual Damage 2. Frequency Tol.<= 5% E4 Life (High Temp.) MIL-STD-202G, 108A, cond. A Temp: 85°C; Time: 96 hours After 2 Hours Recovery 1. No Visual Damage 2. Frequency Tol.<= 5% R1 RoHS With Reference to IEC 62321:2008 with flow chart Directive RoHS 2002/95/EC R2 PFOS With Reference to USA EPA 3540C:1996 by LC/MS Directive RoHS 2006/122/EC R3 PFOA With Reference to USA EPA 3540C:1996 by LC/MS Directive RoHS 2006/122/EC
Yuechung International Corp. (YIC) 11 YYIICC 10. OTHER
10.1 Caution of use
10.1.1 Please don’t apply excess mechanical stress to the component and terminals at soldering. 10.1.2 The component may be damaged when an excess stress will be applied. 10.1.3 This specification mentions the quality of the component as a single unit. Please insure the component is thoroughly evaluated in your application circuit.
10.2 Notice
10.2.1 Please return one of these specifications after your signature of acceptance.