ATPG1590R1040A YIC | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 5
Technical content
GPS & GLONASS Patch Antenna ATPG1590R1040A Datasheet www.yic.com.tw YYIICC
Yuechung International Corp. (YIC) 2 YYIICC ATPG Series 1. Scope This specification shall cover the characteristics of the dielectric antenna element with the type ATPG1590R1040A 2. PART NO.：ATPG1590R1040A 3. Outline Drawing and Dimensions 3.1 Appearance: No visible damage and dirt. 3.2 The products conform to the RoHS directive and national environment protection law.
3.3 Dimensions
- Electrical Specifications
4.1 Performance Characteristics
Nominal frequency MHz GPS: 1575.42±1 MHz GLONASS: 1609±3 MHz Center frequency 1592±30 MHz -10dB Bandwidth MHz min 3 VSWR at CF max 1.5 Polarization Model RHCP Impedance 50 Ω Frequency Temperature Coefficient 20ppm/deg. ℃max
Yuechung International Corp. (YIC) 3 YYIICC ATPG Series
4.2 Impedance Characteristic
- Test
5.1 Test Conditions
Parts shall be measured under a condition (Temp.:20℃±15℃, Humidity : 65%±20% R.H.).
5.2 Test fixture
Yuechung International Corp. (YIC) 4 YYIICC ATPG Series 6. Environmental Test No. Item Test Condition Remark
6.1 Humidity Test
The device is subjected to 90%~95% relative humidity 60℃±3℃ for 96h,then dry out at 25℃ ±5℃ and less than 65% relative humidity for 2h~4h. After dry out the device shall satisfy the specification in table 1. It shall fulfill the specifications in Table 1. 6.2 High Temperature Exposure The device shall satisfy the specification in table 1 after leaving at 85℃ for 96h,provided it would be measured after 2h~4h leaving in 25℃±5 ℃ and less than 65% relative humidity. It shall fulfill the specifications in Table 1.
6.3 Low
The device shall satisfy the specification in table 1 after leaving at -40℃ for 96h,provided it would be measured after 2h~4h leaving in 25℃±5 ℃ and less than 65% relative humidity. It shall fulfill the specifications in Table 1.
6.4 Temperature
Subject the device to -40℃ for 30 min. followed by a high temperature of 85℃ for 30 min cycling shall be repeated 5 times. At the room temperature for 1h prior to the measurement. It shall fulfill the specifications in Table 1.
6.5 Vibration
Subject the device to vibration for 2h each in x、y and z axis with the amplitude of 1.5mm, the frequency shall be varied uniformly between the limits of 10Hz~55Hz. It shall fulfill the specifications in Table 1.
6.6 Soldering Test
Lead terminals are heated up to 350℃±10℃ for 5s±0.5 s with brand iron and then element shall be measured after being placed in natural conditions for 1 h. No visible damage and it shall fulfill the specifications in Table 1 It shall fulfill the specifications in Table 1.
6.7 Solder ability
Lead terminals are immersed in soldering bath of 260℃~290℃ for 3s±0.5s . More than 95% of the terminal surface of the device shall be covered with fresh solder. The terminals shall be at least 95% covered by solder. 6.8 Terminal Pressure Strength Force of 2kg is applied to each lead in axial direction for 10s±1 s (see drawing). No visible damage and it shall fulfill the specifications in Fig 1 Mechanical damage such as breaks shall not occur.
Yuechung International Corp. (YIC) 5 YYIICC ATPG Series FIG 1 PRESS TABLE 1 Item Specification After Test (MHz) Center Frequency change ±2.0 -10dB Bandwidth Change ±2.0 7. Other
7.1 Caution of use
7.1.1 Please don’t apply excess mechanical stress to the component and terminals at soldering. 7.1.2 The component may be damaged when an excess stress will be applied. 7.1.3 This specification mentions the quality of the component as a single unit. Please insure the component is thoroughly evaluated in your application circuit.
7.2 Notice
7.2.1 Please return one of these specifications after your signature of acceptance.