ASX210A1HZ

ASX2001H NAIS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

7.4 .29115.0 .591 8.2 .323 mm inch 7.4 .29115.0 .591 Max. 10.0 .394

FEATURES

1. High contact reliability over a long life has been made possible for low level loads. Using a low level load (1 mV 10 m A to 10 V 10 mA) 10 operations were achieved with a static contact resistance of Max. 100 m W (voltage drop of 20 mV, 1 mA, 1 kHz) and a dynamic contact resistance of Max. W (Measurement delay 10 ms, voltage drop of 20 mV, 1 mA, 1 kHz). 2. High sensitibity of 50 mW By using the highly efficient polar magnet- ic circuit "seesaw balance armature mechanism", a rated power consumption of 50 mW (for single side stable type) has been achieved. 3. Low thermal electromotive force Reducing the heat from the coil enables a thermal electromotive force of 3 m V or less. SPECIFICATIONS Contact Notes: This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the ac- tual load. For single side stable only. Characteristics Remarks: * Specifications will vary with foreign standards certification ratings. By nominal switching capacity: No. of operations: 10 Measurement at same location as "Initial breakdown voltage" section. Detection current: 10mA. Nominal voltage applied to the coil, excluding contact bounce time. By resistive method, nominal voltage applied to the coil; contact carrying current: 10mA. Half-wave pulse of sine wave: 6 ms; detection time: 10 m Half-wave pulse of sine wave: 6 ms. Detection time: 10 m Refer to 5. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT (Page 61) Arrangement 2 Form C Static contact resistance (During initial and electric life tests)* (By voltage drop of 20 mV 1 mA [1kHz]) Max. 100 m W Dynamic contact resistance (During initial and electric life tests)* (By voltage drop of 20 mV 1 mA[1 kHz], Mea- surement delay 10 ms after applying nominal coil voltage) Max. 1 W Contact material Gold-clad silver alloy Rating Nominal switching capacity (resistive load) 10 mA 10 VDC Max. switching power 0.1 W Max. switching voltage 10 VDC Max. switching current 10 mA DC Min. switching capacity m A 1 mVDC Nominal operating power Single side stable 50mW (1.5 to 12 V DC) 70mW (24 V DC) 1 coil latching 35mW (1.5 to 12 V DC) 50mW (24 V DC) 2 coil latching 70mW (1.5 to 12 V DC) 150mW (24 V DC) Thermal electromotive force, max. (at nominal voltage applied to the coil ) 3 m V Expected life (min. operations) Mechanical (at 750 cpm) 5 Electrical (at 750 cpm) (10 mA 10 V DC resistive load) 10 Initial insulation resistance* Min. 10,000M W (at 500V DC) Initial breakdown voltage* Between open contacts 750 Vrms for 1min. Between contact sets 1,000 Vrms for 1min. Between contact and coil 1,800 Vrms for 1min. Operate time [Set time]* (at 20 C) Max. 5 ms (Approx. 3 ms) [Max. 5 ms (Approx. 3 ms)] Release time (without diode) [Reset time]* (at 20 Max. 5 ms (Approx. 1.5 ms) [Max. 5 ms (Approx. 3 ms)] Temperature rise* (at 20 C) Max. 50 C Shock resistance Functional* Min. 750 m/s {75G] Destructive* Min. 1,000 m/s {100G] Vibration resistance Functional* 10 to 55 Hz at double amplitude of 3.3 mm Destructive 10 to 55 Hz at double amplitude of 5 mm Conditions for operation, transport and storage* (Not freezing and con- densing at low tempera- ture) Ambient temperature –40 C to 70 C –40 F to 158 F Humidity 5 to 85% R.H. Unit weight Approx. 2 g .071 oz TYPICAL APPLICATIONS This relay will be used for the small load for measuring instruments or others where a stable contact resistance is required. TESTING

ORDERING INFORMATION

200A Z 1HEx. ASX Contact arrangement Terminal shapeOperating function Packing styleCoil voltage (DC) Nil: Standard PC board terminal A: Surface-mount terminal 2: 2 Form C 0: Single side stable 1: 1 coil latching 2: 2 coil latching Type of operation 0: Standard type (B.B.M.) Nil: Tube packing Tape and reel packing (piked from 8/9/10/12 pin side) 1H: 1.5V 03 : 3V 4H: 4.5V : 6V 09 : 9V 12 : 12V 24 : 24V Note: Tape and reel packing symbol “-Z” is not marked on the relay. “X” type tape and reel packing (picked from 1/3/4/5-pin side) is also available. Suffix “X” instead of “Z”. TYPES AND COIL DATA (at 20 C 68 (1) Standard PC board terminal 1) Standard packing: 40 pcs. in an inner package (tube); 1,000 pcs. in an outer package 2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. Single side stable 1 coil latching 2 coil latching Part No. Coil Rating, V DC Pick-up voltage, V DC (max.) (initial) Drop-out voltage, V DC (min.) (initial) Nominal operating current, mA ( 10%) Coil resistance, W 10%) Nominal operating power, mW Max. allowable voltage, V DC Standard PC board terminal ASX20003 3 2.4 0.3 16.7 180 50 4.5 ASX20006 6 4.8 0.6 8.3 720 50 9 ASX20009 9 7.2 0.9 5.6 1,620 50 13.5 ASX20012 12 9.6 1.2 4.2 2,880 50 18 ASX20024 24 19.2 2.4 2.9 8,229 70 36 Part No. Coil Rating, V DC Set voltage, V DC (max.) (initial) Reset voltage, V DC (max.) (initial) Nominal operating current, mA ( 10%) Coil resistance, W 10%) Nominal operating power, mW Max. allowable voltage, V DC Standard PC board terminal ASX21003 3 2.4 2.4 11.7 257 35 4.5 ASX21006 6 4.8 4.8 5.8 1,029 35 9 ASX21009 9 7.2 7.2 3.9 2,314 35 13.5 ASX21012 12 9.6 9.6 2.9 4,114 35 18 ASX21024 24 19.2 19.2 2.1 11,520 50 36 Part No. Coil Rating, V DC Set voltage, V DC (max.) (initial) Reset voltage, V DC (max.) (initial) Nominal operating current, mA ( 10%) Coil resistance, W 10%) Nominal operating power, mW Max. allowable voltage, V DCStandard PC board terminal Set coil Reset coil Set coil Reset coil Set coil Reset coil ASX22006 6 4.8 4.8 11.7 11.7 514 514 70 70 9 ASX22012 12 9.6 9.6 5.8 5.8 2,057 2,057 70 70 18 ASX22024 24 19.2 19.2 6.3 6.3 3,840 3,840 150 150 36

(2) Surface-mount terminal 1) Standard packing: 40 pcs.(tube), 1,000pcs. (tape and reel)in an inner package; 500 pcs.(tube), 1,000pcs. (tape and reel)in an outer package 2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. Single side stable 1 coil latching type 2 coil latching type Part No. Coil Rating, V DC Pick-up voltage, V DC (max.) (initial) Drop-out voltage, V DC (min.) (initial) Nominal operating current, mA ( 10%) Coil resistance, W 10%) Nominal operating power, mW Max. allowable voltage, V DC Tube packing Tape and reel packing ASX200A03 ASX200A03Z 3 2.4 0.3 16.7 180 50 4.5 ASX200A06 ASX200A06Z 6 4.8 0.6 8.3 720 50 9 ASX200A09 ASX200A09Z 9 7.2 0.9 5.6 1,620 50 13.5 ASX200A12 ASX200A12Z 12 9.6 1.2 4.2 2,880 50 18 ASX200A24 ASX200A24Z 24 19.2 2.4 2.9 8,229 70 36 Part No. Coil Rating, V DC Set voltage, V DC (max.) (initial) Reset voltage, V DC (max.) (initial) Nominal operating current, mA ( 10%) Coil resistance, W 10%) Nominal operating power, mW Max. allowable voltage, V DC Tube packing Tape and reel packing ASX210A03 ASX210A03Z 3 2.4 2.4 11.7 257 35 4.5 ASX210A06 ASX210A06Z 6 4.8 4.8 5.8 1,029 35 9 ASX210A09 ASX210A09Z 9 7.2 7.2 3.9 2,314 35 13.5 ASX210A12 ASX210A12Z 12 9.6 9.6 2.9 4,114 35 18 ASX210A24 ASX210A24Z 24 19.2 19.2 2.1 11,520 50 36 Part No. Coil Rating, V DC Set voltage, V DC (max.) (initial) Reset voltage, V DC (max.) (initial) Nominal operating current, mA ( 10%) Coil resistance, W 10%) Nominal operating power, mW Max. allowable voltage, V DCTube packing Tape and reel packing Set coil Reset coil Set coil Reset coil Set coil Reset coil ASX220A06 ASX220A06Z 6 4.8 4.8 11.7 11.7 514 514 70 70 9 ASX220A12 ASX220A12Z 12 9.6 9.6 5.8 5.8 2,057 2,057 70 70 18 ASX220A24 ASX220A24Z 24 19.2 19.2 6.3 6.3 3,840 3,840 150 150 36 DIMENSIONS 1. PC board terminal Single side stable/ 1 coil latching 0.5 .020 1.15 .045 2.54 .100 3.5 .138 0.65 .026 5.08 .200 0.25 .010 15.0 .591 5.08 .200 8.2 .323 7.4 .291 mm inch 2 coil latching 0.5 .020 1.15 .045 2.54 .100 3.5 .138 0.65 .026 5.08 .200 0.25 .010 15.0 .591 5.08 .200 8.2 .323 7.4 .291 General tolerance: 0.3 .012 PC board pattern 5.08 .200 2.54 .100 8-1.0 dia. 8-.039 dia. 10.16 .400 5.08 .200 2.54 .100 10-1.0 dia. 10-.039 dia. 12.7 .500 Tolerance: 0.1 .004 Schematic (Bottom view) Single side stable (Deenergized condition) 1 coil latching (Reset condition) Direction indication 12 10 9 8 1 3 4 5 Direction indication 12 10 9 8 1 3 4 5 2 coil latching (Reset condition) Direction indication 12 10 9 8 7 1 3 4 5 6

1. Surface-mount terminal Single side stable/ 1 coil latching 5.08 .200 5.08 .200 2.54 .100 0.65 .026 9.4–0.5 .370–.020 15.0 .591 0.5 .020 8.2 .323 7.4 .291 Max.10.0 .394 0.25 .010 1.15 .045 mm inch 2 coil latching 5.08 .200 5.08 .200 2.54 .100 0.65 .026 0.25 .010 9.4–0.5 .370–.020 0.5 .020 8.2 .323 15.0 .591 Max.10.0 .394 7.4 .291 1.15 .045 General tolerance: 0.3 .012 Suggested mounting pad 5.08 .200 /,/, /,/, /,/, /,/, /,/, /,/, /,/, /,/, /,/, /,/,/, /,/,/, /,/, /,/, /, /,/, /,/, /,/, /,/, /,/, /,/, /,/, /, /,/, /,/, /,/, /,/, /,/, /,/, /,/, /, /, /,/, /, /,/,/, /,/, /, /, /,/,/,/, 1.0 .039 2.54 .100 3.16 .124 7.24 .285 5.08 .200 1.0 .039 2.54 .100 3.16 .124 7.24 .285 /,/, /,/, /,/, /,/,/,/, /,/, /,/, /,/, /,/, /,/, /,/, /,/, /, /,/, /,/, /,/, /,/, /,/, /,/, /,/, /,/, /,/,/, /,/, /,/, /,/,/, /, /, /,/, /, /,/,/,/,/, Tolerance: 0.1 .004 Schematic (Top view) Single side stable (Deenergized condition) 1 coil latching (Reset condition) Direction indication 12 10 9 8 1 3 4 5 Direction indication 12 10 9 8 1 3 4 5 2 coil latching (Reset condition) Direction indication 12 10 9 8 7 1 3 4 5 6 REFERENCE DATA 1. Switching capacity range 2-(1). Change in dynamic contact resistance (10 mA 10 V DC resistive load) Tested: ASX20012, Quantity: n=10 Operating frequency: 750 cpm Measured condition: 10 ms after applying nominal coil voltage, using voltage drop of 20 mV, 1 mA, 1 kHz. 2-(2). Change in dynamic contact resistance (10 m A 1 mV DC resistive load) Tested: ASX20012, Quantity: n=10 Operating frequency: 750 cpm Measured condition: 10 ms after applying nominal coil voltage, using voltage drop of 20 mV, 1 mA, 1 kHz. 10mA 10µA 1mV 10V Contact voltage Contact current 1,0000 Min.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Max. No. of operations, · 104 Contact resistance, W 2,0001,0000 Min.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Max. No. of operations, · 104 Contact resistance, W 3-(1). Change in static contact resistance (10 mA 10 V DC resistive load) Tested: ASX20012, Quantity: n=10 Operating frequency: 750 cpm 3-(2). Change in static contact resistance (10 m A 1 mVDC resistive load) Tested: ASX20012, Quantity: n=10 Operating frequency: 750 cpm 1,0000 Max. Min. Max. Min. 100 No. of operations, · 104 Contact resistance, mW N.C. side contact N.O. side contact 2,0001,0000 Max. Min. Max. Min. 100 No. of operations, · 10 Contact resistance, mW N.C. side contact N.O. side contact

1. Coil operating power 1) As a general rule, only a pure DC pow- er supply should be used for the coil drive. 2) To ensure proper operation, the voltage applied to both terminals of the coil should be –5% (at 20°C 68°F) the rated operating voltage of the coil. Also, be aware that the pick-up and drop-out voltages will fluctu- ate depending on the ambient tempera- ture and operating conditions. 3) The ripple factor for the voltage applied to the coil should be less than 5%. 4) For set and reset latching relays, the rated operating voltage should be applied to the coil for 10 ms or more. 2. Coil connection When connecting coils, refer to the wiring diagram to prevent mis-operation or mal- function. 3. External magnetic field Since SX relays are highly sensitive polar- ized relays, their characteristics will be af- fected by a strong external magnetic field. Avoid using the relay under that condition. 4. Cleaning In automatic cleaning, cleaning with the boiling method is recommended. Avoid ul- trasonic cleaning which subject the relay to high frequency vibrations. It may cause the contacts to stick. lt is recommended that a fluorinated hy- drocarbon or other alcoholic solvent be used. 5. Packing style 1) The relay is packed in a tube with the relay orientation mark on the left side, as shown in the figure below. 2) Tape and reel packing (1) Tape dimensions mm inch (2) Dimensions of plastic reelmm inch 6. Automatic insertion To maintain the internal function of the re- lay, the chucking pressure should not ex- ceed the values below. Chucking pressure in the direction A:

4.9 N {500 gf} or less

Chucking pressure in the direction B:

9.8 N {1 kgf} or less

Chucking pressure in the direction C: Please chuck the portion. Avoid chucking the center of the relay. In addition, excessive chucking pressure to the pinpoint of the relay should be also avoided. Orientation (indicates PIN No.1)stripe Stopper (gray) Stopper (green) SX relays Relay polarity bar (Z type) Tape coming out direction General tolerance –0.1 mm .004 inch 4.0–0.1 .157–.004 1.75–0.1 .069–.0042.0–0.1 .079–.004 0.40–0.1 .016–.004 10.8–0.2 .425–.008 16.0–0.1 .630–.004 10.0–0.1 .394–.004 1.50 dia. .059 dia. +0.1 0+.003 /#06/#06 /#06 11.5–0.1.453–.004 .787 24.0–0.3 .945–.012 21–0.8 dia. .827–.031 dia. 13–0.2 dia. .512–.008 dia. 24.4 .961 +.079 100–1 dia. 3.937–.039 dia. 2.0–0.2 .079–.008 370–2 dia. 14.567–.079 dia. 2.0–0.5 .079–.020 A C B For Cautions for Use, see Relay Technical Information (Page 48 to 76). 9/1/2000 All Rights Reserved, © Copyright Matsushita Electric Works, Ltd. Go To Online Catalog