AS1108

AS1108 TAOS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 21

Technical content

The technical content of this austriamicrosystems datasheet is still valid. Contact information: Headquarters: ams AG Tobelbaderstrasse 30

8141 Unterpremstaetten, Austria

Tel: +43 (0) 3136 500 0 e-Mail: ams_sales@ams.com Please visit our website at www.ams.com

1 General Description

conventional 4-wire serial interface. brightness can be controlled by analog or digital means. directly address each segment. can be synchronized across multiple drivers. The device is available in a SOIC 20-pin package. Figure 1. AS1108 - Typical Application Diagram

2 Key Features

3 Applications

4 Digits

8 Segments

4 Pinout

Figure 2. Pin Assignments (Top View) Table 1. Pin Descriptions

1 DOUT

common cathode. The AS1108 pulls the digit outputs to VDD when turned off. 4, 7 GND Ground . Both GND pins must be connected.

9 LOAD/CSN

the rising edge of this pin.

10 CLK

only while pin LOAD/CSN is low. driver is turned off it is pulled to GND.

15 ISET

16 VDD Positive Supply Voltage. Connect to +2.7 to +5.5V supply.

www.austriamicrosystems.com/LED-Driver-ICs/AS1108 Revision 2.13 3 - 20 AS1108 Datasheet - Abs olute M aximu m Rating s

5 Absolute Maximum Ratings

Stresses beyond those listed in Table 2 may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in Section 6 Electrical Characteristics on page 4 is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. T able 2. Absolute Maximum Ratings Parameter Min Max Units Notes Electrical Parameters VDD to GND -0.3 7 V All other pins to GND -0.3 V DD + 0.3 (max 7V) V Current DIG 0:DIG 3 Sink Current 500 mA SEG A:SEG G, SEG DP 100 mA Latch-Up Immunity ±200 mA All pins except AS1108 pin 11: ±180 mA Norm: JEDEC 78 Electrostatic Discharge Digital outputs 1000 V Norm: MIL 883 E method 3015 All other pins 1000 V Continuous Power Dissipation (TA = +85°C) Wide SOIC 941 mW Derate 11.8mW/ºC above +70ºC Temperature Ranges and Storage Conditions Storage Temperature Range -55 +150 ºC Package Body Temperature (Wide SOIC) +260 ºC The reflow peak soldering temperature (body temperature) specified is in accordance with IPC/ JEDEC J-STD-020 “Moisture/Reflow Sensitivity Classification for Non-Hermetic Solid State Surface Mount Devices”. The lead finish for Pb-free leaded packages is matte tin (100% Sn). Humidity 5 85 % Non-condensing Moisture Sensitive Level 3 Represents a max. floor life time of 168h ams AG Technical content still valid

6 Electrical Characteristics

Table 3. Electrical Characteristics Table 4. Logic Inputs/Outputs Characteristics

Table 5. Timing Characteristics (see Figure 10 on page 8)

7 Typical Operating Characteristics

VDD = 5V, RSET = 9.53kΩ , TAMB = 25ºC (unless otherwise specified). Figure 3. Scan Frequency vs.Temperature Figure 4. Scan Frequency vs. VDD Figure 5. ISEG vs. Temperature Figure 6. ISEG vs. VDD Figure 7. ISEG vs. VOUT Figure 8. ISEG vs. VOUT

Figure 9. ISEG vs. RSET

8 Detailed Description

on page 9) via the 4-wire serial interface. A programming sequence consists of 16-bit packages as depicted in Table 6. clocked out at the falling edge of CLK. data. The first bit is D15, the most significant bit (MSB). The exact timing is shown in Figure 10. into shutdown mode. All registers should be programmed for normal operation at this time. Register (see page 12) is set to the minimum values. Figure 10. Interface Timing Table 6. 16-Bit Serial Data Format

DD , so that all segments are blanked. Note: During shutdown mode the Digit-Registers maintain their data. ble. Only the display test mode (see page 11) overrides shutdown mode. selected using a 4-bit address word, and communication is done via the serial interface. without rewriting the whole register contents. down, display test and features selection registers. Table 7. Register Address Map

The Shutdown Register controls AS1108 shutdown mode (see Shutdown Mode on page 9). on). Table 10 lists some examples of the possible settings for the Decode Enable Register bits. Note: A logic high enables decoding and a logic low bypasses the decoder altogether. D7 = 1 turns the decimal point on). Table 10 lists the code-B font; Table 11 lists the HEX font. AS1108. Table 12 shows the 1:1 pairing of each data bit and the appropriate segment line. Figure 11. Standard 7-Segment LED Intensity Control and Inter-Digit Blanking Table 8. Shutdown Register Format (Address (HEX) = 0xXC)) Table 9. Decode Enable Register Format (Address (HEX) = 0xX9)) Table 10. Code-B Font

0 X 0 0 0 0 1 1 1 1 1 1 0

1 X 0 0 0 1 0 1 1 0 0 0 0

2 X 0 0 1 0 1 1 0 1 1 0 1

3 X 0 0 1 1 1 1 1 1 0 0 1

4 X 0 1 0 0 0 1 1 0 0 1 1

5 X 0 1 0 1 1 0 1 1 0 1 1

Test Register is set for normal operation. Note: All settings of the Digit- and Control-Registers are maintained.

6 X 0 1 1 0 1 0 1 1 1 1 1

7 X 0 1 1 1 1 1 1 0 0 0 0

8 X 1 0 0 0 1 1 1 1 1 1 1

9 X 1 0 0 1 1 1 1 1 0 1 1

The decimal point is enabled by setting bit D7 = 1. Table 11. HEX Font The decimal point is enabled by setting bit D7 = 1. Table 12. No-Decode Mode Data Bits and Corresponding Segment Lines Table 13. Display-Test Register Format (Address (HEX) = 0xXF)) Table 10. Code-B Font (Continued)

means using RSET (see Selecting RSET Resistor Value and Using External Drivers on page 14). down to 1/32 of the peak current set by RSET . update frequency is typically 1600Hz. If the number of digits displayed is reduced, the update frequency is increased. fewer than 4 digits are used. Note: To avoid differences in brightness this register should not be used to blank parts of the display (leading zeros). Table 14. Intensity Register Format (Address (HEX) = 0xXA)) Table 15. Scan-Limit Register Format (Address (HEX) = 0xXB)) Table 16. Maximum Segment Current for 1-, 2-, or 3-Digit Displays

blinking rate, and resetting the blink timing. Note: At power-up the Feature Register is initialized to 0. Figure 12 on page 16). The LOAD/CSN and CLK signals are connected to all devices. operation command, and subsequently update its register. Table 17. Feature Register Summary Table 18. Feature Register Bit Descriptions (Address (HEX) = 0xXE)) Enables and disables various device features. 0 = Internal oscillator is used for system clock. 1 = Pin CLK of the serial interface operates as system clock input. Resets all control registers except the Feature Register. 0 = Reset Disabled. Normal operation. Register) identically after power-up. Note: The Digit Registers maintain their data. 0 = Enable Code-B decoding (see Table 10 on page 10). 1 = Enable HEX decoding (see Table 11 on page 11). Enables the SPI-compatible interface. 0 = Disable SPI-compatible interface. 1 = Enable the SPI-compatible interface. 0 = Blink period typically is 1 second (0.5s on, 0.5s off). 1 = Blink period is 2 seconds (1s on, 1s off). timing can be synchronized across all the devices. bit D7 determines how blinking starts. 0 = Blinking starts with the display turned off. 1 = Blinking starts with the display turned on.

9 Typical Application

effects of electromagnetic interference and wiring inductance. avoid power supply ripple (see Figure 12 on page 16). Note: Both GND pins must be connected to ground. current that flows through the LEDs. Table 19. RSET vs. Segment Current and LED Forward Voltage, VDD = 2.7V Table 20. RSET vs. Segment Current and LED Forward Voltage, VDD = 3.3V Table 21. RSET vs. Segment Current and LED Forward Voltage, VDD = 3.6V Table 22. RSET vs. Segment Current and LED Forward Voltage, VDD = 4.0V

Table 23. RSET vs. Segment Current and LED Forward Voltage, VDD = 5.0V Table 24. Package Thermal Data

20 Wide SOIC +85° C/W

Table 22. RSET vs. Segment Current and LED Forward Voltage, VDD = 4.0V (Continued)

The application example in Figure 12 shows the AS1108 as a 4x8 LED dot matrix driver. bit D7 corresponds to segment DP . Note: For a multiple-digit dot matrix, multiple AS1108 devices must be cascaded. Figure 12. Application Example as LED Dot Matrix Driver should be set to the same value so that one display will not appear brighter than the other. cycle per digit. If 5 digits are needed, set both Scan-Limit Registers to display 3 digits and leave one digit unconnected. because its duty cycle per digit will be 1/2 and the other display’s duty cycle will be 1/3. Note: Refer to No-Op Register (0xX0) on page 13 for additional information.

Figure 13. SOIC 20-pin Marking Table 25. Packaging Code YYWWRZZ

Figure 14. SOIC 20-pin Package

The AS1108 is available as the standard products shown in Table 26. Note: All products are RoHS compliant and austriamicrosystems green. Table 26. Ordering Information

www.austriamicrosystems.com/LED-Driver-ICs/AS1108 Revision 2.13 2 0 - 20 AS1108 Datasheet Copyrights Copyright © 1997-2012, austriamicrosystems AG, Tobelbaderstrasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. Disclaimer Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the tech- nical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Contact Information Headquarters austriamicrosystems AG Tobelbaderstrasse 30 A-8141 Unterpremstaetten, Austria Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact ams AG Technical content still valid