AR0230

AR0230 ONSEMI | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 36

Technical content

Features

AR0230CS/D Rev. 8, Pub. 11/15 EN 1 ©Semiconductor Components Industries, LLC 2015, 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor AR0230CS Datasheet, Rev. 8 For the latest datasheet, please visit www.onsemi.com

• Superior low-light performance  Latest 3.0 m pixel with ON Semiconductor DR-Pix™ technology with Dual Conversion Gain  Full HD support at up to 1080P 60 fps for superior video performance  Linear or high dynamic range capture  Optional adaptive local tone mapping (ALTM)  Pixel or Line interleaved T1/T2 output  Support for external mechanical shutter  On-chip phase-locked loop (PLL) oscillator  Integrated position-based color and lens shading correction  Slave mode for precise frame-rate control  Stereo/3D camera support  Statistics engine  Data interfaces: four-lane serial high-speed pixel interface (HiSPi) differential signaling (SLVS and HiV CM), or parallel  Auto black level calibration  High-speed configurable context switching T e m p e r a t u r e s e n s o r

Applications

 Video surveillance  1080p60 (Surveillance) video applications  High dynamic range imaging General Description ON Semiconductor's AR0230CS is a 1/2.7-inch CMOS digital image sensor with an active-pixel array of 1928Hx1088V . It captures images in either linear or high dynamic range modes, with a rolling-shutter readout. It includes sophisticated camera functions such as in-pixel binning, windowing and both video and single frame modes. It is designed for both low light and high dynamic range scene performance. It is programmable through a simple two-wire serial inter- face. The AR0230CS produces extraordinarily clear, sharp digital pictures, and its ability to capture both continuous video and single frames makes it the per- fect choice for a wide range of applications, including surveillance and HD video. Table 1: Key Parameters Parameter Typical Value Optical format 1/2.7-inch (6.6 mm) Active pixels 1928(H) x 1088(V) (16:9 mode) Pixel size 3.0 m x 3.0m Color filter array RGB Bayer Shutter type Electronic rolling shutter and GRR Input clock range 6 – 48 MHz Output clock maximum

148.5 Mp/s (4-lane HiSPi)

74.25 Mp/s (Parallel)

Output Serial HiSPi 10-, 12-, 14-, 16-, or 20-bit Parallel 10-, 12-bit Frame rate 1080p 60 fps Responsivity 4.0 V/lux-sec SNR MAX 41 dB Max Dynamic range Up to 96 dB Supply voltage I/O 1.8 or 2.8 V Digital 1.8 V Analog 2.8 V HiSPi 0.3 V - 0.6 V (SLVS), 1.7 V - 1.9 V (HiVcm) Power consumption (typical) 386 mW (Linear, 1080p30, 25C, parallel output) 558 mW (HDR, 1080p30, 25C, parallel output) Operating temperature –30°C to +85°C ambient Package options 10x10 mm 80-pin iBGA

AR0230CS/D Rev. 8, Pub. 11/15 EN 2 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor

Ordering Information

See the ON Semiconductor Device Nomenclature document (TND310/D) for a full description of the naming convention used for image sensors. For reference documenta- tion, including information on evaluation kits, please visit our web site at www.onsemi.com. Table 2: Available Part Numbers Part Number Product Description Orderable Product Attribute Description AR0230CSSC00SUEA0-DRBR 2 Mp 1/3" CIS RGB, 0deg CRA, iBGA Package Drypack, Anti-Reflective Glass AR0230CSSC00SUEAD3-GEVK RGB, 0deg CRA, Demo Kit Demo Kit AR0230CSSC00SUEAH3-GEVB RGB, 0deg CRA, Headboard Headboard AR0230CSSC12SUEA0-DR 2 Mp 1/3" CIS RGB, 12deg CRA, iBGA Package Drypack AR0230CSSC12SUEAD3-GEVK RGB, 12deg CRA, Demo Kit Demo Kit AR0230CSSC12SUEAH3-GEVB RGB, 12deg CRA, Headboard Headboard

AR0230CS/D Rev. 8, Pub. 11/15 EN 3 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Table of Contents Table of Contents

AR0230CS/D Rev. 8, Pub. 11/15 EN 5 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor List of Tables List of Tables

AR0230CS/D Rev. 8, Pub. 11/15 EN 6 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor General Description General Description The ON Semiconductor AR0230CS can be operated in its default mode or programmed for frame size, exposure, gain, and other parameters. The default mode output is a 1080p-resolution image at 60 frames per second (fps) through the HiSPi port. In linear mode, it outputs 12-bit or 10-bit A-Law compressed raw data, using either the parallel or serial (HiSPi) output ports. In high dynamic range mode, it outputs 12-bit compressed data using parallel output. In HiSPi mode, 12- or 14-bit compressed, or 16-bit linearized data may be output. The device may be operated in video (master) mode or in single frame trigger mode. FRAME_VALID and LINE_VALID signals are output on dedicated pins, along with a synchronized pixel clock in parallel mode. The AR0230CS includes additional features to allow application-specific tuning: windowing and offset, auto black level correction, and on-board temperature sensor. Optional register information and histogram statistic information can be embedded in the first and last 2 lines of the image frame. The AR0230CS is designed to operate over a wide temperature range of -30°C to +85°C ambient.

AR0230CS/D Rev. 8, Pub. 11/15 EN 7 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Functional Overview Functional Overview The AR0230CS is a progressive-scan sensor that generates a stream of pixel data at a constant frame rate. It uses an on-chip, phase-locked loop (PLL) that can be optionally enabled to generate all internal clocks from a single master input clock running between 6 and 48 MHz. The maximum output pixel rate is 148.5 Mp/s, corresponding to a clock rate of 74.25 MHz. Figure 1 shows a block diagram of the sensor configured in linear mode, and in HDR mode. Figure 1: Block Diagram of AR0230CS User interaction with the sensor is through the two-wire serial bus, which communi- cates with the array control, analog signal chain, and digital signal chain. The core of the sensor is a 2.1 Mp Active- Pixel Sensor array. The timing and control circuitry sequences through the rows of the array, resetting and then reading each row in turn. In the time interval between resetting a row and reading that row, the pixels in the row integrate incident light. The exposure is controlled by varying the time interval between reset and readout. Once a row has been read, the data from the columns is sequenced through an analog signal chain (providing offset correction and gain), and then through an analog- to-digital converter (ADC). The output from the ADC is a 12-bit value for each pixel in the array. The ADC output passes through a digital processing signal chain (which provides further data path corrections and applies digital gain). The sensor also offers a Row Noise Correction Black Level Correction Test Pattern Generator Pixel Defect Correction Adaptive CD Filter Digital Gain and Pedestal A-Law Compression Parallel HiSPi 12 bit s 10 bits ADC Data HDR Linearization Smoothing Filter Digital Gain and Pedestal Companding or ALTM Parallel HiSPi 12 bits 14 or 12 bits 16 bits Row Noise Correction Black Level Correction Test Pattern Generator Pixel Defect Correction Adaptive CD Filter Motion Correction ADC Data HDR Linearization In Linear Mode In HDR Mode

AR0230CS/D Rev. 8, Pub. 11/15 EN 8 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Functional Overview high dynamic range mode of operation where multiple images are combined on-chip to produce a single image at 16-bit per pixel value. A compression mode is further offered to allow the 16 bits per pixel to be transmitted to the host system as a 12-bit value with close to zero loss in image quality. Figure 2: Typical Configuration: Serial Four-Lane HiSPi Interface Notes: 1. All power supplies mu st be adequately decoupled. 2. ON Semiconductor recommends a resistor value of 1.5k , but a greater value may be used for slower two-wire speed. 3. The parallel interface output pads can be left un connected if the serial output interface is used. 4. ON Semiconductor recommends that 0.1 F and 10F decoupling capacitors for each power supply are mounted as close as possible to the pad. Actual values and results may vary depending on lay- out and design considerations. Refer to the AR0230CS demo headboard schematics for circuit rec- ommendations. 5. ON Semiconductor recommends that analog power planes are placed in a manner such that cou- pling with the digital power planes is minimized. 6. I/O signals voltage must be configured to match V DD_IO voltage to minimize any leakage currents. VDD_IO V DD_SLVS V DD_PLLVDD VAA VDD VAA VAA_PIX Master clock (6–48 MHz) SDATA SCLK RESET_BAR TEST EXTCLK DGND AGND Digital ground Analog ground Digital Core power1 HiSPi power1 Analog power1 To controller From controller VDD_IO VDD_PLL PLL power1 Digital I/O power1 1.5kΩ2 1.5kΩ2 Analog power1 VAA_PIX SLVSC_N SLVSC_P SLVS0_P SLVS0_N SLVS1_P SLVS1_N SLVS2_P SLVS2_N SLVS3_P SLVS3_N VDD_SLVS TRIGGER OE_BAR SADDR SHUTTER FLASH

AR0230CS/D Rev. 8, Pub. 11/15 EN 9 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Functional Overview Figure 3: Typical Configuration: Parallel Pixel Data Interface Notes: 1. All power supplies mu st be adequately decoupled. 2. ON Semiconductor recommends a resistor value of 1.5k , but a greater value may be used for slower two-wire speed. 3. The serial interface output pads and V DDSLVS can be left unconnected if the parallel output inter- face is used. 4. ON Semiconductor recommends that 0.1 F and 10F decoupling capacitors for each power supply are mounted as close as possible to the pad. Actual values and results may vary depending on lay- out and design considerations. Refer to the AR0230CS demo headboard schematics for circuit rec- ommendations. 5. ON Semiconductor recommends that analog power planes are placed in a manner such that cou- pling with the digital power planes is minimized. 6. I/O signals voltage must be configured to match V DD_IO voltage to minimize any leakage currents. 7. The EXTCLK input is limited to 6-48 MHz. VDD Master clock (6-48 MHz) SDATA SCLK TEST FRAME_VALID DOUT [11:0]EXTCLK DGND Digital ground Analog ground Digital core power1 To controller From Controller LINE_VALID PIXCLK RESET_BAR VDD_IO Digital I/O power1 1.5kΩ2 1.5kΩ2, VAA VAA_PIX Analog power1 VDD_PLL PLL power1 Analog power1 VAA_PIXVDD_IO V DD_PLLVDD VAA TRIGGER OE_BAR AGND SADDR SHUTTER FLASH

AR0230CS/D Rev. 8, Pub. 11/15 EN 10 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Functional Overview Figure 4: 80-Ball IBGA Package A B C D E F G H J Top View (Ball Down) SLVS0_P SLVS1_P SLVSC_P SLVS2_P SLVS3_P VDD_PLL SLVS0_N SLVS1_N SLVSC_N SLVS2_N SLVS3_N EXTCLK VDD_ SLVSDGND DGND VDD DGND SADDR SCLKSDATA AGND DGND VDD_IO VAA_PIX LINE_ VALID FRAME_ VALID PIXCLK FLASH DOUT7 DOUT1 DOUT11 D OUT10 DOUT9 TESTDOUT4D OUT3 DOUT6DOUT8 DGND TRIGGER OE_BARDOUT0DOUT2 DOUT5 RESET_ BAR 12 3 567 8 4 VDD DGND SHUTTER Reserved DGND VAA VAA VAA VAA VDD VDD VDD VDD VDD Reserved DGND DGND DGND DGND DGND DGND DGND DGND AGND AGND AGND VDD_IO VDD_IO VDD_IO VDD_IO VDD_IO AGNDDGND DGND VDD_IO

AR0230CS/D Rev. 8, Pub. 11/15 EN 11 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Functional Overview Table 3: Pin Descriptions, 80-ball iBGA Name iBGA Pin Type Description SLVS0_P A2 Output HiSPi serial data, lane 0, differential P . SLVS1_P A3 Output HiSPi serial data, lane 1, differential P . SLVSC_P A4 Output HiSPi serial DDR clock differential P . SLVS2_P A5 Output HiSPi serial data, lane 2, differential P . SLVS3_P A6 Output HiSPi serial data, lane 3, differential P . VDD_PLL B1 Power PLL power. SLVS0_N B2 Output HiSPi serial data, lane 0, differential N. SLVS1_N B3 Output HiSPi serial data, lane 1, differential N. SLVSC_N B4 Output HiSPi serial DDR clock differential N. SLVS2_N B5 Output HiSPi serial data, lane 2, differential N. SLVS3_N B6 Output HiSPi serial data, lane 3, differential N. SHUTTER B9 Output Control for external mechanical shutte r. Can be left floating if not used. VAA C1, G1, D9, F9 Power Analog power. AGND C2, G2, D8, E8, F8 Power Analog ground. (R0x306E[9]) bit to 1 when configuring VDD_SLVS to 1.7 – 1.9V. VDD C5, J5, A9, H9, A7, D1, F1 Power Digital power. Reserved C9, F7 DGND B7, C7, D7, E7, G7, B8, C8, G8, D2, E2, F2, H2, C3, G3, H3, C6, Power Digital ground. EXTCLK D3 Input External input clock. PIXCLK D4 Output Pixel clock out. Dout is valid on rising edge of this clock. SADDR D5 Input Two-Wire Serial address select. 0: 0x20. 1: 0x30 TRIGGER D6 Input Exposure synchronization input. VAA_PIX E9 Power Pixel power. VDD_IO E1, H1, J2, J7, A8, G9, J9 Power I/O supply power. SDATA E3 I/O Two-Wire Serial data I/O. FLASH E4 Output Flash control output. FRAME_VALID E5 Output Asserted when Dout frame data is valid. SCLK E6 Input Two-Wire Serial clock input. DOUT11 F3 Output Parallel pixel data output (MSB) DOUT10 F4 Output Parallel pixel data output. DOUT9F 5 Output Parallel pixel data output. LINE_VALID F6 Output Asserted when Do ut line data is valid. DOUT8G 4 Output Parallel pixel data output. DOUT7G 5 Output Parallel pixel data output. DOUT6G 6 Output Parallel pixel data output. DOUT5H 4 Output Parallel pixel data output. DOUT4H 5 Output Parallel pixel data output. DOUT3H 6 Output Parallel pixel data output. RESET_BAR H7 Input Asynchronous reset (active LOW). All settings are restored to factory default.

AR0230CS/D Rev. 8, Pub. 11/15 EN 12 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Functional Overview TEST H8 Input. Manufacturing test enable pin (connect to Dgnd). DOUT2J 1 Output Parallel pixel data output. DOUT1J 3 Output Parallel pixel data output. DOUT0J 4 Output Parallel pixel data output (LSB) OE_BAR J8 Input Output enable (active LOW). Table 3: Pin Descriptions, 80-ball iBGA Name iBGA Pin Type Description

AR0230CS/D Rev. 8, Pub. 11/15 EN 13 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Pixel Data Format Pixel Data Format Pixel Array Structure While the sensor's format is 1928 x1088, additional active columns and active rows are included for use when horizontal or vertical mirrored readout is enabled, to allow readout to start on the same pixel. The pixel adjustment is always performed for mono- chrome or color versions. The active area is surrounded with optically transparent dummy pixels to improve image uniformity within the active area. Not all dummy pixels or barrier pixels can be read out. Figure 5: Pixel Array Description 10 barrier + 4 border pixels Light dummy pixel Active pixel 10 barrier + 4 border pixels 1944 2 barrier + 6 border pixels 2 barrier + 6 border pixels 1116 19281 x 1088 5.78 mm x 3.26 mm

AR0230CS/D Rev. 8, Pub. 11/15 EN 15 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Features Overview Features Overview For a complete description, recommendations, and usage guidelines for product features, refer to the AR0230CS Developer Guide. 3.0m Dual Conversion Gain Pixel To improve the low light performance and keep the high dynamic range, a large (3.0um) dual conversion gain pixel is implemented for better image optimization. With a dual conversion gain pixel, the conversion gain of the pixel may be dynamically changed to better adapt the pixel response based on dynamic range of the scene. This gain can be switched manually or automatically by an auto exposure control module. HDR By default, the sensor powers up in HDR Mode. The HDR scheme used is multi-exposure HDR. This allows the sensor to handle up to 96 dB of dynamic range. In HDR mode, the sensor sequentially captures two exposures by maintaining two separate read and reset pointers that are interleaved within the rolling shutter readout. The intermediate pixel values are stored in line buffers while waiting for the two exposure values to be present. As soon as a pixel's two exposure values are available, they are combined to create a linearized 16-bit value for each pixel's response. The exposure ratio may be set to 4x, 8x, 16x, or 32x. Depending on whether HiSPi or Parallel mode is selected, the full 16 bit value may be output, it can be compressed to 12 bits using Adaptive Local Tone Mapping (ALTM), or companded to 12 or 14 bits. Options to output T1 only, T2 only, or pixel interleaved data are also available. Individual exposures may be read out in a line interleaved mode as described in the T1/T2 Line Interleaved Mode section. Resolution The active array supports a maximum of 1928x1088 pixels to support 1080p resolution. Utilizing a 3.0um pixel will result in an optical format of 1/2.7-inch (approximately 6.6mm diagonal). Frame Rate At full (1080p) resolution, the AR0230CS is capable of running up to 3060 fps. Image Acquisition Mode The AR0230CS supports two image acquisition modes:  Electronic rolling shutter (ERS) mode This is the normal mode of operation. When the AR0230CS is streaming, it generates frames at a fixed rate, and each frame is integrated (exposed) using the ERS. When ERS mode is in use, timing and control logic within the sensor sequences through the rows of the array, resetting and then reading each row in turn. In the time interval between reset- ting a row and subsequently reading that row, the pixels in the row integrate incident light. The integration (exposure) time is controlled by varying the time between row reset and row readout. For each row in a frame, the time between row reset and row readout is the same, leading to a uniform integration time across the frame. When the integration time is changed (by using the two-wire serial interface to change register settings), the timing and control logic controls the transition from old to new integration

AR0230CS/D Rev. 8, Pub. 11/15 EN 16 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Features Overview time in such a way that the stream of output frames from the AR0230CS switches cleanly from the old integration time to the new while only generating frames with uniform inte- gration. See “Changes to Integration Time” in the AR0230CS Register Reference.  Global reset mode. This mode can be used to acquire a single image at the current resolution. In this mode, the end point of the pixel integration time is controlled by an external electromechanical shutter, and the AR0230CS provides control signals to interface to that shutter. The benefit of using an external electromechanical shutter is that it eliminates the visual arti- facts associated with ERS operation. Visual artifacts arise in ERS operation, particularly at low frame rates, because an ERS image effectively integrates each row of the pixel array at a different point in time. Embedded Data and Statistics The AR0230CS has the capability to output image data and statistics embedded within the frame timing. There are two types of information embedded within the frame readout. E m b e d d e d D a t a : If enabled, these are displayed on the two rows immediately before the first active pixel row is displayed.  Embedded Statistics: If enabled, these are displayed on the two rows immediately after the last active pixel row is displayed. Multi-Camera Synchronization The AR0230CS supports advanced line synchronization controls for multi-camera (stereo) support. Slave Mode The slave mode feature of the AR0230CS supports triggering the start of a frame readout from an input signal that is supplied from an external ASIC. The slave mode signal allows for precise control of frame rate and register change updates. Context Switching and Register Updates The user has the option of using the highly configurable context memory, or a simplified implementation in which only a subset of registers is available for switching. The AR0230 supports a highly configurable context switching RAM of size 256 x 16. Within this Context Memory, changes to any register may be stored. The register set for each context must be the same, but the number of contexts and registers per context are limited only by the size of the context memory. Alternatively, the user may switch between two predefined register sets A and B by writing to a context switch change bit. When the context switch is configured to context A the sensor will reference the context A registers. If the context switch is changed from A to B during the readout of frame n, the sensor will then reference the context B coarse_integration_time registers in frame n+1 and all other context B registers at the beginning of reading frame n+2. The sensor will show the same behavior when changing from context B to context A. The registers listed in Table 4 are context-switchable:

AR0230CS/D Rev. 8, Pub. 11/15 EN 17 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Features Overview Table 4: List of Configurable Registers for Context A and Context B Motion Compensation/DLO In typical multi-exposure HDR systems, motion artifacts can be created when objects move during the T1 or T2 integration time. When this happens, edge artifacts can poten- tially be visible and might look like a ghosting effect. To correct this, the AR0230CS has special 2D motion compensation circuitry that detects motion artifacts and corrects the image. The motion compensation feature can be optionally enabled by register write. Additional parameters are available to control the extent of motion detection and correction as per the requirements of the specific application. Tone Mapping Real-world scenes often have a very high dynamic range (HDR) that far exceeds the elec- trical dynamic range of the imager. Dynamic range is defined as the luminance ratio between the brightest and the darkest objects in a scene. Even though the AR0230CS can capture full dynamic range images, the images are still limited by the low dynamic range of display devices. Today's typical LCD monitor has a contrast ratio around 1,000:1 while it is not atypical for an HDR image having a contrast ratio of around 250,000:1. There- fore, in order to reproduce HDR images on a low dynamic range display device, the captured high dynamic range must be compressed to the available range of the display device. This is commonly called tone mapping. The AR0230CS has implemented an adaptive local tone mapping (ALTM) feature to reproduce visually appealing images that increase the local contrast and the visibility of the images. Context A Context B Register Description Register Description coarse_integration_time coarse_integration_time_cb line_length_pck line_length_pck_cb frame_length_lines frame_length_lines_cb row_bin row_bin_cb col_bin col_bin_cb fine_gain fine_gain_cb coarse_gain coarse_gain_cb x_addr_start x_addr_start_cb y_addr_start y_addr_start_cb green1_gain green1_gain_cb blue_gain blue_gain_cb red_gain red_gain_cb green2_gain green2_gain_cb global_gain global_gain_cb operation_mode_ctrl operation_mode_ctrl_cb bypass_pix_comb bypass_pix_comb_cb

AR0230CS/D Rev. 8, Pub. 11/15 EN 18 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Features Overview Adaptive Color Difference (ADACD) Noise Filtering A good noise reduction filter will remove noise from an image while retaining as much image detail as possible. To retain image detail, the noise reduction filter must adapt to the image signal. To remove noise, the noise reduction filter must adapt to the noise level of the image signal. The key is to remove the appropriate amount of noise. Over-filtering will cause image blurring while under-filtering will leave noise in the image. The AdaCD algorithm relies on a noise model derived from characterization data to aid in separating noise from signal. The AR0230CS AdaCD algorithm performs pixel-by-pixel color noise correction for each of the red, blue, and green color planes. Each pixel is corrected based on surrounding pixel values on the same color plane and a noise model. The noise model is based on characterization data, and takes into account applied analog gain. Fast Mode Switch (Combi Mode) To facilitate faster switching between linear and HDR modes, the AR0230CS includes a Combi Mode feature. When enabled, Combi Mode loads a single (HDR) sequencer. When switching from HDR to linear modes, the sequencer remains the same, but only the T1 image is output. While not optimized for linear mode operation, it allows faster mode switching as a new sequencer load is not needed. Switching between modes may result in the output of one bad frame. Analog/Digital Gains A programmable analog gain of 1.5x to 12x (HDR) and 1.5x to 16x (linear) applied simul- taneously to all color channels will be featured along with a digital gain of 1x to 16x that may be configured on a per color channel basis. Skipping/Binning Modes The AR0230CS supports subsampling. Subsampling allows the sensor to read out a smaller set of active pixels by either skipping, binning, or summing pixels within the readout window. Horizontal binning is achieved in the digital readout. The sensor will sample the combined 2x adjacent pixels within the same color plane. Vertical row binning is applied in the pixel readout. Row binning can be configured as 2x rows within the same color plane. Pixel skipping can be configured up to 2x in both the x-direction and y-direction. Skipping pixels in the x-direction will not reduce the row time. Skipping pixels in the y direction will reduce the number of rows from the sensor effectively reducing the frame time. Skipping will introduce image artifacts from aliasing. The AR0230CS supports row wise vertical binning. Row wise vertical summing is not supported. Clocking Options The sensor contains a phase-locked loop (PLL) that is used for timing generation and control. The required VCO clock frequency is attained through the use of a pre-PLL clock divider followed by a multiplier. The PLL multiplier should be an even integer. If an odd integer (M) is programmed, the PLL will default to the lower (M-1) value to maintain an even multiplier value. The multiplier is followed by a set of dividers used to generate the output clocks required for the sensor array, the pixel analog and digital readout paths, and the output parallel and serial interfaces. Use of the PLL is required when using the HiSPi interface.

AR0230CS/D Rev. 8, Pub. 11/15 EN 19 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Features Overview Temperature Sensor The AR0230CS sensor has a built-in PTAT-based temperature sensor, accessible through registers, that is capable of measuring die junction temperature. The value read out from the temperature sensor register is an ADC output value that needs to be converted downstream to a final temperature value in degrees Celsius. Since the PTAT device char- acteristic response is quite linear in the temperature range of operation required, a simple linear function can be used to convert the ADC output value to the final tempera- ture in degrees Celsius. A single reference point will be made available via register read as well as a slope for back-calculating the junction temperature value. An error of +/-5% or better over the full specified operating range of the sensor is to be expected. Silicon / Firmware / Sequencer Revision Information A revision register will be provided to read out (via I2C) silicon and sequencer/OTPM revision information. This will be helpful to distinguish among different lots of material if there are future OTPM or sequencer revisions. Lens Shading Correction The latest lens shading correction algorithm will be included for potential low Z height applications. Companding The 16-bit linearized HDR image may be compressed to 12- or 14- bits using on-chip companding. This is useful if on-chip ALTM will not be used and the ISP cannot handle 16 bit data. Compression When the AR0230CS is configured for linear mode operation, the sensor can optionally compress 12-bit data to 10-bit using A-law compression. The A-law compression is disabled by default. Packaging The AR0230CS will be offered in a 10x10 80-iBGA package (parallel and HiSPi). The package will have anti-reflective coating on both sides of the cover glass. Parallel Interface The parallel pixel data interface uses these output-only signals: F R A M E _ V A L I D L I N E _ V A L I D P I X C L K OUT[11:0] The parallel pixel data interface is disabled by default at power up and after reset. It can be enabled by programming R0x301A. When the parallel pixel data interface is in use, the serial data output signals can be left unconnected.

AR0230CS/D Rev. 8, Pub. 11/15 EN 20 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Features Overview High Speed Serial Pixel (HiSPi) Interface The HiSPi interface supports three protocols, Streaming-S, Streaming-SP , and Packetized SP . The streaming protocols conform to a standard video application where each line of active or intra-frame blanking provided by the sensor is transmitted at the same length. The Packetized SP protocol will transmit only the active data ignoring line-to-line and frame-to-frame blanking data. The HiSPi interface building block is a unidirectional differential serial interface with four data and one double data rate (DDR) clock lanes. One clock for every four serial data lanes is provided for phase alignment across multiple lanes. The AR0230CS supports serial data widths of 10, 12, 14, 16, or 20 bits on one, two, or four lanes. The specification includes a DLL to compensate for differences in group delay for each data lane. The DLL is connected to the clock lane and each data lane, which acts as a control master for the output delay buffers. Once the DLL has gained phase lock, each lane can be delayed in 1/8 unit interval (UI) steps. This additional delay allows the user to increase the setup or hold time at the receiver circuits and can be used to compensate for skew introduced in PCB design. Delay compensation may be set for clock and/or data lines in the hispi_timing register R0x31C0. If the DLL timing adjustment is not required, the data and clock lane delay settings should be set to a default code of 0x0000 to reduce jitter, skew, and power dissipation. Sensor Control Interface The two-wire serial interface bus enables read/write access to control and status regis- ters within the AR0230CS. The interface protocol uses a master/slave model in which a master controls one or more slave devices. The sensor acts as a slave device. The master generates a clock (SCLK) that is an input to the sensor and is used to synchronize trans- fers. Data is transferred between the master and the slave on a bidirectional signal (SDATA). SDATA is pulled up to VDD_IO off-chip by a 1.5k resistor. Either the slave or master device can drive SDATA LOW-the interface protocol determines which device is allowed to drive SDATA at any given time. The two-wire serial interface can run at 100 kHz or 400 kHz. T1/T2 Line Interleaved Mode The AR0230CS has the capability to output the T1 and T2 exposures separately, in a line interleaved format. The purpose of this is to enable off chip HDR linear combination and processing. See the AR0230CS Developer Guide for more information.

AR0230CS/D Rev. 8, Pub. 11/15 EN 21 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Features Overview Figure 8: Quantum Efficiency 350 450 550 650 750 850 950 1050 1150 Quantum Efficiency (%) Wavelength (nm) Blue Green (B) Green (R) Red

AR0230CS/D Rev. 8, Pub. 11/15 EN 22 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Electrical Specifications Electrical Specifications Unless otherwise stated, the following specifications apply under the following condi- VDD_SLVS = 0.4V – 0.1/+0.2; TA = -30°C to +85°C-40°C to +105°C; output load = 10pF; frequency = 74.25 MHz; HiSPi off. Two-Wire Serial Register Interface The electrical characteristics of the two-wire serial register interface (SCLK, SDATA) are shown in Figure 9 and Table 5. Figure 9: Two-Wire Serial Bus Timing Parameters Note: Read sequence: For an 8-bit READ, read waveforms start after WRITE command and register address are issued. Table 5: Two-Wire Serial Bus Characteristics Parameter Symbol Standard Mode Fast Mode UnitMin Max Min Max SCLK Clock Frequency fSCL 0 100 0 400 KHz Hold time (repeated) START condition. After this period, the first clock pulse is generated tHD;STA 4.0 - 0.6 - s LOW period of the SCLK clock tLOW 4.7 - 1.3 - s HIGH period of the SCLK clock tHIGH 4.0 - 0.6 - s Set-up time for a repeated START condition tSU;STA 4.7 - 0.6 - s Data hold time tHD;DAT 0 4 3.455 06 0.95 s Data set-up time tSU;DAT 250 - 100 6 -n s Rise time of both SDATA and SCLK signals tr - 1000 20 + 0.1Cb 7 300 ns Fall time of both SDATA and SCLK signals tf - 300 20 + 0.1Cb 7 300 ns Set-up time for STOP condition tSU;STO 4.0 - 0.6 - s Bus free time between a STOP and START condition tBUF 4.7 - 1.3 - s Capacitive load for each bus line Cb - 400 - 400 pF S Sr tSU;STOtSU;STAtHD;STA tHIGH tLOW tSU;DAT tHD;DAT tf SDATA SCLK P S tBUFtr tftr tHD;STA

AR0230CS/D Rev. 8, Pub. 11/15 EN 23 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Electrical Specifications Notes: 1. This table is based on I 2C standard (v2.1 January 2000). Philips Semiconductor. 2. Two-wire control is I 2C-compatible. 4. A device must internally provide a hold time of at least 300 ns for the SDATA signal to bridge the undefined region of the falling edge of SCLK. 5. The maximum tHD;DAT has only to be met if the device does not stretch the LOW period (tLOW) of the SCLK signal. 6. A Fast-mode I 2C-bus device can be used in a Standard-mode I2C-bus system, but the requirement tSU;DAT 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCLK signal. If such a device does stretch the LOW period of the SCLK signal, it must output the next data bit to the SDATA line tr max + tSU;DAT = 1000 + 250 = 1250 ns (according to the Standard-mode I2C-bus specification) before the SCLK line is released. 7. Cb = total capacitance of one bus line in pF. I/O Timing By default, the AR0230CS launches pixel data, FV , and LV with the falling edge of PIXCLK. The expectation is that the user captures DOUT[11:0], FV , and LV using the rising edge of PIXCLK. See Figure 10 below and Table 6 on page 24 for I/O timing (AC) characteristics. Figure 10: I/O Timing Diagram Serial interface input pin capacitance CIN_SI - 3.3 - 3.3 pF SDATA max load capacitance CLOAD_SD - 30 - 30 pF SDATA pull-up resistor RSD 1.5 4.7 1.5 4.7 K  Table 5: Two-Wire Serial Bus Characteristics (continued) Parameter Symbol Standard Mode Fast Mode UnitMin Max Min Max Data[11:0] LINE_VALID/ PIXCLK EXTCLK tR tEXTCLK tF FRAME_VALID leads LINE_VALID by 6 PIXCLKs. FRAME_VALID trails LINE_VALID by 6 PIXCLKs. tPLH tPFH tPFL tPLL tPD Pxl _0 Pxl _1 Pxl _2 Pxl _n 90% 10% tRP tFP 90% 10% FRAME_VALID

AR0230CS/D Rev. 8, Pub. 11/15 EN 24 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Electrical Specifications Note: I/O timing characteristics are me asured under the following conditions: - Temperature is 25°C ambient - 10 pF load - 1.8V I/O supply voltage Table 6: I/O Timing Characteristics Symbol Definition Condition Min Typ Max Unit fEXTCLK1s Input clock frequency 6 – 48 MHz tEXTCLK1 Input clock period 20.8 – 166 ns tR Input clock rise time – 3 – ns tF Input clock fall time – 3 – ns tRP Pixclk rise time 2 3.5 5 ns tFP Pixclk fall time 2 3.5 5 ns Clock duty cycle 45 50 55 % tCP EXTCLK to PIXCLK propagation delay Nominal voltages, PLL Disabled 10 14 18 ns fPIXCLK PIXCLK frequency Default, Nominal Voltages 67 4 . 2 5 M H z tPD PIXCLK to data valid Default, Nominal Voltages 3.6 5.5 9.5 ns tPFH PIXCLK to FV HIGH Default, Nominal Voltages 2.9 5.3 9 ns tPLH PIXCLK to LV HIGH Default, Nominal Voltages 2.9 5 9 ns tPFL PIXCLK to FV LOW Default, Nominal Voltages 2.9 5 9 ns tPLL PIXCLK to LV LOW Default, Nominal Voltages 2.9 4.8 9 ns CLOAD Output load capacitance – <10 – pF CIN Input pin capacitance – 2.5 – pF

AR0230CS/D Rev. 8, Pub. 11/15 EN 25 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Electrical Specifications The DC electrical characteristics are shown in the tables below. Caution Stresses greater than those listed in Table 8 may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other con- ditions above those indicated in the operational sections of this specification is not implied. Note: Exposure to absolute maximum rating condit ions for extended periods may affect reliability. Table 7: DC Electrical Characteristics Symbol Definition Condition Min Typ Max Unit VDD Core digital voltage 1.7 1.8 1.95 V VAA Analog voltage 2.5 2.8 3.1 V VAA_PIX Pixel supply voltage 2.5 2.8 3.1 V VDD_PLL PLL supply voltage 2.5 2.8 3.1 V VDD_SLVS HiSPi supply voltage 0.3 0.4 0.6 V VIH Input HIGH voltage V DD_IO*0.7 – – V VIL Input LOW voltage – – V DD_IO*0.3 V IIN Input leakage current No pull-up resistor; VIN = VDD_IO or DGND 20 – – A VOH Output HIGH voltage V DD_IO-0.3 – – V VOL Output LOW voltage – – 0.4 V IOH Output HIGH current At specified V OH -22 – – mA IOL Output LOW current At specified V OL ––2 2 m A Table 8: Absolute Maximum Ratings Symbol Definition Condition Min Max Unit VDD_MAX Core digital voltage –0.3 2.4 V VDD_IO_MAX I/O digital voltage –0.3 4 V VAA_MAX Analog voltage –0.3 4 V VAA_PIX Pixel supply voltage –0.3 4 V VDD_PLL PLL supply voltage –0.3 4 V VDD_SLVS_MAX HiSPi I/O digital voltage –0.3 2.4 V tST Storage temperature –40 85 °C

AR0230CS/D Rev. 8, Pub. 11/15 EN 26 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Electrical Specifications Note: Operating currents are measured in mA at the following conditions: - VAA = VAA_PIX = VDD_PLL = VDD_IO =2.8 V - VDD= 1.8 V - PLL Enabled and PIXCLK = 74.25 MHz - Low power mode enabled - T A = 25°C Note: Operating currents are measured in mA at the following conditions: - VAA = VAA_PIX = VDD_PLL = VDD_IO =2.8 V - VDD= 1.8 V - PLL Enabled and PIXCLK = 74.25 MHz - Low power mode enabled - T A = 25°C Note: Operating currents are measured in mA at the following conditions: - VAA = VAA_PIX = VDD_PLL =2.8 V - VDD = VDD_IO= 1.8 V - PLL Enabled and PIXCLK = 74.25 MHz - Low power mode enabled - TA = 25°C Table 9: 1080p30 HDR (ALTM) 74MHz Parallel 2.8V Definition Condition Symbol Voltage Min Typ Max Digital operating current Streaming 1080p30 I DD 1.8 90 175 220 I/O digital operating current Streaming 1080p30 I DD_IO 2.8 10 30 50 Analog operating current Streaming 1080p30 I AA 2 . 8 3 54 58 5 Pixel supply current Streaming 1080p30 I AA_PIX 2.8 2 4 7 PLL supply current Streaming 1080p30 I DD_PLL 2.8 5.5 6.2 7 Power (mW) 309 557.76 813.2 Table 10: 1080p30 Linear 74MHz Parallel 2.8V Definition Condition Symbol Voltage Min Typ Max Digital operating current Streaming 1080p30 I DD 1.8 75 107 145 I/O digital operating current Streaming 1080p30 I DD_IO 2.8 10 30 50 Analog operating current Streaming 1080p30 I AA 2 . 8 2 03 05 0 Pixel supply current Streaming 1080p30 I AA_PIX 2.8 1 3 7 PLL supply current Streaming 1080p30 I DD_PLL 2.8 5.5 6.2 7 Power (mW) 237.2 386.36 580.2 Table 11: 1080p30 HDR (ALTM) 74MHz Parallel 1.8V Definition Condition Symbol Voltage Min Typ Max Digital operating current Streaming 1080p30 I DD 1.8 90 175 220 I/O digital operating current Streaming 1080p30 I DD_IO 1.8 10 20 30 Analog operating current Streaming 1080p30 I AA 2.8 35 45 85 Pixel supply current Streaming 1080p30 I AA_PIX 2.8 2 4 7 PLL supply current Streaming 1080p30 I DD_PLL 2.8 5.5 6.2 7 Power (mW) 299 509.76 727.2

AR0230CS/D Rev. 8, Pub. 11/15 EN 27 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Electrical Specifications Note: Operating currents are measured in mA at the following conditions: - VAA = VAA_PIX = VDD_PLL =2.8 V - VDD = VDD_IO= 1.8 V - PLL Enabled and PIXCLK = 74.25 MHz - Low power mode enabled - T A = 25°C Note: Operating currents are measured in mA at the following conditions: - VAA = VAA_PIX = VDD_PLL =2.8 V - VDD = VDD_IO= 1.8 V - VDD_SLVS= 0.4V - PLL Enabled and PIXCLK = 37.125 MHz - 4-lane HiSPi mode - Low power mode enabled - T A = 25°C Table 12: 1080p30 Linear 74 MHz Parallel 1.8V Definition Condition Symbol Voltage Min Typ Max Digital operating current Streaming 1080p30 I DD 1.8 75 107 145 I/O digital operating current Streaming 1080p30 I DD_IO 1.8 10 20 30 Analog operating current Streaming 1080p30 I AA 2.8 20 30 50 Pixel supply current Streaming 1080p30 I AA_PIX 2.8 1 3 7 PLL supply current Streaming 1080p30 I DD_PLL 2.8 5.5 6.2 7 Power (mW) 227.2 338.36 494.2 Table 13: 1080p30 HDR (ALTM) 74 MHz HiSPi SLVS (Low Power Mode) Definition Condition Symbol Voltage Min Typ Max Digital Operating Current Streaming 1080p30 I DD 1.8 145 175 235 Analog Operating Current Streaming 1080p30 I DD_IO 2.8 25 46 65 Pixel Supply Current Streaming 1080p30 I AA 2.8 1 4 7 PLL Supply Current Streaming 1080p30 I AA_PIX 2.8 6 7.4 8.5 SLVS Supply Current Streaming 1080p30 I DD_PLL 0.4 3 9 14 Power (mW) 351.8 479.32 654

AR0230CS/D Rev. 8, Pub. 11/15 EN 28 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Electrical Specifications Note: Operating currents are measured in mA at the following conditions: - VAA = VAA_PIX = VDD_PLL =2.8 V - VDD = VDD_IO= 1.8 V - VDD_SLVS= 0.4V - PLL Enabled and PIXCLK = 74.25 MHz - 4-lane HiSPi mode - Low power mode enabled - T A = 25°C Note: Operating currents are measured in mA at the following conditions: - VAA = VAA_PIX = VDD_PLL =2.8 V - VDD = VDD_IO = VDD_SLVS = 1.8 V - PLL Enabled and PIXCLK = 37.125 MHz - 4-lane HiSPi mode - Low power mode enabled - T A = 25°C Table 14: 1080p30 Linear 74 MHz HiSPi SLVS Definition Condition Symbol Voltage Min Typ Max Digital Operating Current Streaming 1080p30 I DD 1.8 75 115 155 Analog Operating Current Streaming 1080p30 I DD_IO 2.8 20 30 50 Pixel Supply Current Streaming 1080p30 I AA 2.8 1 3 7 PLL Supply Current Streaming 1080p30 I AA_PIX 2.8 6 7.4 8.5 SLVS Supply Current Streaming 1080p30 I DD_PLL 0.4 3 9 14 Power (mW) 211.8 323.72 468 Table 15: 1080p30 HDR (ALTM) 74 MHz HiSPi HiVcm (Low Power Mode) Definition Condition Symbol Voltage Min Typ Max Digital Operating Current Streaming 1080p30 I DD 1.8 145 175 235 Analog Operating Current Streaming 1080p30 I DD_IO 2.8 25 46 65 Pixel Supply Current Streaming 1080p30 I AA 2 . 8 147 PLL Supply Current Streaming 1080p30 I AA_PIX 2.8 6 7.4 8.5 SLVS Supply Current Streaming 1080p30 I DD_PLL 1.8 10 20 30 Power (mW) 368.6 511.72 702.4

AR0230CS/D Rev. 8, Pub. 11/15 EN 29 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Electrical Specifications Note: Operating currents are measured in mA at the following conditions: - VAA = VAA_PIX = VDD_PLL =2.8 V - VDD = VDD_IO = VDD_SLVS= 1.8 V - PLL Enabled and PIXCLK = 74.25 MHz - 4-lane HiSPi mode - Low power mode enabled - T A = 25°C Note: Operating currents are measured in mA at the following conditions: - VAA = VAA_PIX = VDD_PLL =2.8 V - VDD = VDD_IO= 1.8 V - VDD_SLVS= 0.4V - PLL Enabled and PIXCLK = 74.25 MHz - 4-lane HiSPi mode - T A= 25°C Table 16: 1080p30 Linear 74 MHz HiSPi HiVcm Definition Condition Symbol Voltage Min Typ Max Digital Operating Current Streaming 1080p30 I DD 1.8 75 115 155 Analog Operating Current Streaming 1080p30 I DD_IO 2.8 20 30 50 Pixel Supply Current Streaming 1080p30 I AA 2 . 8 137 PLL Supply Current Streaming 1080p30 I AA_PIX 2.8 6 7.4 8.5 SLVS Supply Current Streaming 1080p30 I DD_PLL 1.8 10 20 30 Power (mW) 228.6 356.12 516.4 Table 17: Line Interleaved HiSPi SLVS Definition Condition Symbol Voltage Min Typ Max Digital Operating Current Streaming 1080p30 I DD 1.8 185 230 265 Analog Operating Current Streaming 1080p30 I DD_IO 2.8 20 36 55 Pixel Supply Current Streaming 1080p30 I AA 2.8 1 3.3 7 PLL Supply Current Streaming 1080p30 I AA_PIX 2.8 7 8.2 9.5 SLVS Supply Current Streaming 1080p30 I DD_PLL 0.4 3 9 14 Power (mW) 412.6 550.6 668.8

AR0230CS/D Rev. 8, Pub. 11/15 EN 30 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Electrical Specifications Note: Operating currents are measured in mA at the following conditions: - VAA = VAA_PIX = VDD_PLL = 2.8 V - VDD= VDD_IO = 1.8 V - VDD_SLVS = 1.8 V - PLL Enabled and PIXCLK = 74.25 MHz - 4-lane HiSPi mode - TA = 25°C HiSPi Electrical Specifications The ON Semiconductor AR0230CS sensor supports both SLVS and HiVCM HiSPi modes. Refer to the High-Speed Serial Pixel (HiSPi) Interface Physical Layer Specification v2.00.00 for electrical definitions, specifications, and timing information. The V DD_SLVS supply in this datasheet corresponds to VDD_TX in the HiSPi Physical Layer Specifica- tion. Similarly, VDD is equivalent to VDD_HiSPi as referenced in the specification. The DLL as implemented on AR0230CS is limited in the number of available delay steps and differs from the HiSPi specification as described in this section. Table 18: Line Interleaved HiSPi HiVcm Definition Condition Symbol Voltage Min Typ Max Digital Operating Current Streaming 1080p30 I DD 1.8 185 230 265 Analog Operating Current Streaming 1080p30 I DD_IO 2.8 20 36 55 Pixel Supply Current Streaming 1080p30 I AA 2.8 1 3.3 7 PLL Supply Current Streaming 1080p30 I AA_PIX 2.8 7 8.2 9.5 SLVS Supply Current Streaming 1080p30 I DD_ P L L 1 . 81 02 03 0 Power (mW) 429.4 583 717.2 Table 19: Channel Skew Measurement Conditions: VDD_HiSPi = 1.8V;VDD_HiSPi_TX = 0.4V; Data Rate =480 Mbps; DLL set to 0 Data Lane Skew in Reference to Clock tCHSKEW1PHY -150 ps

AR0230CS/D Rev. 8, Pub. 11/15 EN 31 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Power-On Reset and Standby Timing Power-On Reset and Standby Timing Power-Up Sequence The recommended power-up sequence for the AR0230CS is shown in Figure 11. The available power supplies (VDD_IO, VDD, VDD_SLVS, VDD_PLL, VAA, VAA_PIX) must have the separation specified below. 1. Turn on V DD_PLL power supply. 2. After 100 s, turn on VAA and VAA_PIX power supply. 3. After 100 s, turn on VDD_IO power supply. 4. After 100 s, turn on VDD power supply. 5. After 100 s, turn on VDD_SLVS power supply. 6. After the last power supply is stable, enable EXTCLK. 7. Assert RESET_BAR for at least 1ms. The parall el interface will be tri-stated during this time. 8. Wait 150000 EXTCLKs (for internal initialization into software standby. 9. Configure PLL, output, and image settings to desired values. 10. Wait 1ms for the PLL to lock. 11. Set streaming mode (R0x301a[2] = 1). Figure 11: Power Up VDD_PLL (2.8) VAA_PIX VAA (2.8) VDD_IO (1.8/2.8) VDD (1.8) VDD_SLVS (0.4) EXTCLK RESET_BAR tx t5 t6 Hard Reset Internal Initialization Software Standby PLL Lock Streaming

AR0230CS/D Rev. 8, Pub. 11/15 EN 32 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Power-On Reset and Standby Timing Notes: 1. Xtal settling time is component-de pendent, usually taking about 10 – 100 ms. 2. Hard reset time is the minimum time required after power rails are settled. In a circuit where Hard reset is held down by RC circuit, then the RC time must include the all power rail settle time and Xtal settle time. 3. It is critical that V DD_PLL is not powered up after the other power supplies. It must be powered before or at least at the same time as the others. If the case happens that VDD_PLL is powered after other supplies then sensor may have functionality issues and will experience high current draw on this supply. Table 20: Power-Up Sequence Definition Symbol Minimum Typical Maximum Unit VDD_PLL to VAA/VAA_PIX3 t0 0 100 – s VAA/VAA_PIX to VDD_IO t1 0 100 – s VDD_IO to VDD t2 0 100 – s VDD to VDD_SLVS t3 0 100 – s Xtal settle time tx – 30 1 –m s Hard Reset t4 1 2 –– m s Internal Initialization t5 150000 – – EXTCLKs PLL Lock Time t6 1 – – ms

AR0230CS/D Rev. 8, Pub. 11/15 EN 33 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Power-On Reset and Standby Timing Power-Down Sequence The recommended power-down sequence for the AR0230CS is shown in Figure 12. The available power supplies (VDD_IO, VDD, VDD_SLVS, VDD_PLL, VAA, VAA_PIX) must have the separation specified below. 1. Disable streaming if output is acti ve by setting standby R0x301a[2] = 0 2. The soft standby state is reached after the current row or frame, depending on config- uration, has ended. 3. Turn off V DD_SLVS. 4. Turn off V DD. 5. Turn off V DD_IO. 6. Turn off V AA/VAA_PIX. 7. Turn off V DD_PLL. Figure 12: Power Down t4 is required between power down and next power up time; all decoupling caps from regulators must be completely discharged. Table 21: Power-Down Sequence Definition Symbol Minimum Typical Maximum Unit VDD_SLVS to VDD t0 0 – – s VDD to VDD_IO t1 0 – – s VDD_IO to VAA/VAA_PIX t2 0 – – s VAA/VAA_PIX to VDD_PLL t3 0 – – s Power Down until Next Power Up Time t4 100 – – ms V DD_IO (1.8/2.8) t 0 EXTCLK VDD_SLVS (0.4) VDD (1.8) VAA_PIX VAA (2.8) VDD_PLL (2.8) Power Down until next Power up cycle

AR0230CS/D Rev. 8, Pub. 11/15 EN 34 ©Semiconductor Components Industries, LLC, 2015 AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor Power-On Reset and Standby Timing Package Diagrams Figure 13: 80iBGA 10 x 10 Package Diagram

AR0230CS/D Rev. 8, Pub. 11/15 EN 35 ©Semiconductor Components Industries, LLC, 2015. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor

Revision History

I n i t i a l r e l e a s e  Updated Table 1, “Key Parameters,” on page 1  Updated Table 2, “ Available Part Numbers,” on page 1  Updated “Packaging” on page 19  Updated Table 9, “Operating Current Consumption in Parallel Output and Linear Mode,” on page 26  Updated Table 10, “Operating Current Co nsumption in Parallel Output and HDR Mode,” on page 26  Updated Table 11, “Operating Current in HiSPi (HiVCM) Output and Linear Mode,” on page 27  Updated Table 12, “Operating Current in HiSPi (HiVCM) Output and HDR Mode,” on page 27  Updated Table 13, “Operating Current in HiSPi (SLVS) Output and Linear Mode,” on page 28  Updated Table 14, “Operating Current in HiSPi (SLVS) Output and HDR Mode,” on page 28  Deleted references to iLCC package: – Figure 4: 48 iLCC Package, Parallel Output – Table 3: Pin Descriptions – Figure 5: 48 iLCC Package, HiSPi Output – Table 4: Pin Descriptions, 48 iLCC – Figure 16: 48iLCC 10x10 Parallel Package Diagram – Figure 17: 48iLCC 10x10 Serial Package Diagram  Updated to Production  Updated Table 2, “ Available Part Numbers,” on page 1  Updated “General Description” on page 6  Updated “ Analog/Digital Gains” on page 18  Updated “Temperature Sensor” on page 19  Updated “HDR” on page 15  Updated Figure 5: “Pixel Array Description,” on page 13  Replaced Tables 9-14 with Table 10, “1080p 30 Linear 74MHz Parallel 1.8v,” on page 25 to Table 19, “Line Interleaved HiVcm,” on page 29.  Updated “Ordering Information” on page 2  Updated “Ordering Information” on page 2  Updated Rev. History to follow ON Semiconductor rules  Updated “Ordering Information” on page 2  Updated max. dynamic range (from 105 to 96 dB) on p.1 and p. 15  Updated Table 6, “I/O Timing Characteristics,” on page 24

ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s pr oduct/patent coverage may be accessed at www.onsemi.com/site/pdf/ Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaim s any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data shee ts and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SC ILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in whic h the failure of the SCILLC prod uct could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such uninte nded or unauthorized application, Buyer shall indemnify and hol d SCILLC and its officers, employ ees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly o r indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. AR0230CS: 1/2.7-Inch 2.1 Mp/Full HD Digital Image Sensor AR0230CS/D Rev. 8, Pub. 11/15 EN 36 ©Semiconductor Components Industries, LLC, 2015 . DR-Pix is a trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.  Replaced Table 7, “Operating Current Consumption in Parallel Output and Linear Mode,” on page 21 with Table 9, “1080p30 HDR (ALTM) 74MHz Parallel 2.8V ,” on page 26  Replaced Table 8, “Operating Current Consumption in Parallel Output and HDR Mode,” on page 21 with Table 10, “1080p30 Linear 74MHz Parallel 2.8V ,” on page 26  Replaced Table 9, “Operating Current in HiSPi (HiVCM) Output and Linear Mode,” on page 22 with Table 11, “1080p30 HDR (ALTM) 74MHz Parallel 1.8V ,” on page 26  Replaced Table 10, “Operating Current in HiSPi (HiVCM) Output and HDR Mode,” on page 22with Table 12, “1080p30 Linear 74 MHz Parallel 1.8V ,” on page 27  Replaced Table 11, “Operating Current in Hi SPi (SLVS) Output and Linear Mode,” on page 23 with Table 13, “1080p30 HDR (ALTM) 74 MHz HiSPi SLVS (Low Power Mode),” on page 27  Replaced Table 12, “Operating Current in HiSPi (SLVS) Output and HDR Mode,” on page 23 with Table 14, “1080p30 Linear 74 MHz HiSPi SLVS,” on page 28  Added Table 15, “1080p30 HDR (ALTM) 74 MH z HiSPi HiVcm (Low Power Mode),” on page 28, Table 16, “1080p30 Linear 74 MHz HiSPi HiVcm,” on page 29, Table 17, “Line Interleaved HiSPi SLVS,” on page 29, and Table 18, “Line Interleaved HiSPi HiVcm,” on page 30