AQ4020

AQ4020 LITTELFUSE | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Features

• ESD, IEC 61000-4-2, ±30kV contact, ±30kV air
• EFT , IEC 61000-4-4, 40A (5/50ns)
• Lightning, IEC 61000- 4-5 2nd edition, 30A (tP=8/20μs)
• Low capacitance of 2.5pF (@ VR=0V)
• Low leakage current of 0.1μA at 3.3V
• Unidirectional and bidirectional configuration
• Small SOD323 package fits 0805 footprints
• AEC-Q101 Qualified
• Moisture Sensitivity Level(MSL -1)
• Halogen free, lead free and RoHS compliant
• 10/100/1000 Ethernet
• T1/E1/T3/E3
• USB 1 .1/2.0
• Power Ports
• Computers and Peripherals
• Instrumentation
• Medical Equipment
• CAN Bus protection
• Automotive applications Pinout Life Support Note: Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. RoHS Pb GREENAQ4020 Series 2.5pF, 30A Discrete TVS Diode Pin 1 Pin 2 Functional Block Diagram Unidirectional Bidirectional SP4020-01FTG SP4020-01FTG-C AQ4020 Series AQ4020-01FTG AQ4020-01FTG-C

©2018 Littelfuse, Inc. Specifications are subject to change without notice. TVS Diode Arrays (SPA ® Diodes) Revision: 03/07/18 TVS Diode Arrays (SPA® Diodes) Lightning Surge Protection- SP4020 Series Notes: CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the component. This is a stress only rating and operation of the component at these or any other conditions above those indicated in the operational sections of this specification is not implied. Absolute Maximum Ratings Symbol Parameter Value Units IPP Peak Current (tp=8/20μs) 30 A PPk Peak Pulse Power (tp=8/20μs) 735 W TOP Operating Temperature -40 to 150 °C TSTOR Storage Temperature -55 to 150 °C Electrical Characteristics (TOP=25ºC) Parameter Symbol Test Conditions Min Typ Max Units Breakdown Voltage VBD IR=2uA 3.5 V Reverse Standoff Voltage VRWM IR≤1μA 3.3 V Leakage Current ILEAK VR=3.3V 0.1 0.5 μA Clamp Voltage1 VC IPP=1A, tp=8/20µs, Fwd 6.6 V IPP=10A, tp=8/20µs, Fwd 14.2 V IPP=30A, tP=8/20μs, Fwd 24.5 V Dynamic Resistance 2 RDYN TLP , tP=100ns, I/O to GND 0.4 Ω ESD Withstand Voltage1 VESD IEC 61000-4-2 (Contact Discharge) ±30 kV IEC 61000-4-2 (Air Discharge) ±30 kV Diode Capacitance1 CD Reverse Bias=0V , f=1MHz 2.5 pF Note: 1 . Parameter is guaranteed by design and/or component characterization. 2. Transmission Line Pulse (TLP) with 100ns width, 2ns rise time, and average window t1=70ns to t2= 90ns Normalized Capacitance vs. Bias Voltage 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 SP4020- 01FTG-C SP4020- 01FTG Capacitance Bias Voltage (V) AQ4020 Series AQ4020-01FTG-C AQ4020-01FTG 8/20μs Pulse Waveform 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 110% Time (/uni03BCs) Percent of IPP

©2018 Littelfuse, Inc. Specifications are subject to change without notice. TVS Diode Arrays (SPA ® Diodes) Revision: 03/07/18 TVS Diode Arrays (SPA® Diodes) Lightning Surge Protection- SP4020 Series Clamping Voltage vs. IPP 05 10 15 20 25 30 Clamp Voltage (VC ) Peak Pulse Current- IPP (A) Time Temperature TP TL TS(max) TS(min) tP tL tS time to peak temperature PreheatPreheat Ramp-upRamp-up Ramp-downRamp-do Critical Zone TL to TP Critical Zone TL to TP Reflow Condition Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C Soldering Parameters Postive T ransmission Line Pulsing (TLP) Plot 0369 12 15 TLP Voltage (V) TLP Current (A) Negative T ransmission Line Pulsing (TLP) Plot -20 -18 -16 -14 -12 -10 -15- 12 -9 -6 -3 0 TLP Voltage (V) TLP Current (A) AQ4020 Series

©2018 Littelfuse, Inc. Specifications are subject to change without notice. TVS Diode Arrays (SPA ® Diodes) Revision: 03/07/18 TVS Diode Arrays (SPA® Diodes) Lightning Surge Protection- SP4020 Series E b c D A1 A2 A 0.2 0.49 0.45 2.28 1.14 2.77 1.79 Recommended Solder Pad Unit: mm

Ordering Information

Part Number Package Marking Min. Order Qty. AQ4020-01FTG SOD323 03 3000 AQ4020-01FTG-C SOD323 3C 3000 Part Numbering System Part Marking System AQ 01 T G Series Number of Channels Package T= Tape & Reel G= Green Automotive Grade TVS Diode Arrays (SPA Diodes) F: SOD323 F4020 C Blank = Unidirectional C= Bidirectional SP4020-01FTG SP4020-01FTG-C AQ4020 Series AQ4020-01FTG AQ4020-01FTG-C Product Characteristics Lead Plating Matte tin Lead Material Copper Alloy Lead Coplanarity 0.0004 inches (0.102mm) Substrate material Silicon Body Material Molded Compound Flammability UL Recognized compound meeting flammability rating V-0 Notes : 1 . All dimensions are in millimeters 2. Dimensions include solder plating. 3. Dimensions are exclusive of mold flash & metal burr. Symbol SOD323 Millimeters Inches Min Max Min Max A 0.80 1. 0 0 0.031 0.039 A1 0.00 0.10 0.000 0.004 A2 0.80 0.90 0.031 0.035 b 0.25 0.35 0.010 0.014 c 0.08 0.15 0.003 0.006 D 1 .20 1 .40 0.047 0.055 E 1 .60 1 .80 0.063 0.071 E1 2.50 2.70 0.098 0.106 L1 0.25 0.40 0.010 0.016

©2018 Littelfuse, Inc. Specifications are subject to change without notice. TVS Diode Arrays (SPA ® Diodes) Revision: 03/07/18 TVS Diode Arrays (SPA® Diodes) Lightning Surge Protection- SP4020 Series Embossed Carrier T ape & Reel Specification — SOD323 Symbol Millimeters A0 1 .46+/-0.10 B0 2.90+/-0.10 W 8.0+0.3/-0.10 D0 1 .50+0.10 D1 0.45min/1 .15max E1 1 .75+/-0.10 E2 - F 3.50+/-0.10 P0 4.00+/-0.10 P 4.00+/-0.10 P1 2.00+/-0.05 K0 1 .25+/-0.10 T 0.254+/-0.02 Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. ,Ref. ,Ref. ,Ref. 8mm TAPE AND REEL AQ4020 Series Pin1 Component Orientation in Tape