APT2012SYCK-J3-PRV KINGBRIGHT | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
Features
z 2.0mmx1.25mm SMT LED,0.75mm thickness. z Low power consumption. z Wide viewing angle. z Ideal for backlight and indicator. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant.
Description
The Super Bright Yellow device is based on light emitting diode chip made from AlGaInP. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAN0375 REV NO: V.2B DATE: MAR/24/2015 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013837 Selection Guide Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Electrical / Optical Characteristics at TA=25°C Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. Part No. Dice Lens Type Viewing Angle [1] Min. Typ. 2 θ1/2 APT2012SYCK/J3-PRV Super Bright Yellow (AlGaInP) Water Clear 200 320 120° Iv (mcd) [2] @ 20mA Symbol Parameter Device Typ. Max. Units Test Conditions λpeak Peak Wavelength Super Bright Yellow 590 nm I F=20mA λD [1] Dominant Wavelength Super Bright Yellow 590 nm I F=20mA Δλ1/2 Spectral Line Half-width Super Bright Yellow 20 nm I F=20mA C Capacitance Super Bright Yellow 45 pF V F=0V;f=1MHz VF [2] Forward Voltage Super Bright Yellow 2 2.5 V I F=20mA IR Reverse Current Super Bright Yellow 10 uA V R=5V Parameter Super Bright Yellow Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 140 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C
SPEC NO: DSAN0375 REV NO: V.2B DATE: MAR/24/2015 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013837 Super Bright Yellow APT2012SYCK/J3-PRV
SPEC NO: DSAN0375 REV NO: V.2B DATE: MAR/24/2015 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013837 APT2012SYCK/J3-PRV Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm)
SPEC NO: DSAN0375 REV NO: V.2B DATE: MAR/24/2015 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013837 PACKING & LABEL SPECIFICATIONS APT2012SYCK/J3-PRV Terms and conditions for the usage of this document 1. The information included in this docum ent reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the dat asheet. If customer usage exceeds the spec ified limits, Kingbright will not be respon sible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applicati ons. If customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes