APT2012LSECK-J3-PRV KINGBRIGHT | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
Features
z 2.0mmx1.25mm SMT LED,0.75mm thickness. z Low power consumption. z Wide viewing angle. z Ideal for backlight and indicator. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z Low current IF=2mA operating. z RoHS compliant.
Description
The Hyper Red device is based on light emitting diode chip made from AlGaInP. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAN8393 REV NO: V.2A DATE: MAR/09/2015 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1203014460 Selection Guide Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Electrical / Optical Characteristics at TA=25°C Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. Part No. Dice Lens Type Iv (mcd) [2] @ 2mA Viewing Angle [1] Min. Typ. 2 θ1/2 Hyper Red (AlGaInP) Water Clear 50 100 120° *20 *40 APT2012LSECK/J3-PRV Parameter Hyper Red Units Power dissipation 63 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Symbol Parameter Device Typ. Max. Units Test Conditions λpeak Peak Wavelength Hyper Red 640 nm I F=2mA λD [1] Dominant Wavelength Hyper Red 625 nm I F=2mA Δλ1/2 Spectral Line Half-width Hyper Red 20 nm I F=2mA C Capacitance Hyper Red 27 pF V F=0V;f=1MHz VF [2] Forward Voltage Hyper Red 1.8 2.1 V I F=2mA IR Reverse Current Hyper Red 10 uA V R=5V Min. 1.5
SPEC NO: DSAN8393 REV NO: V.2A DATE: MAR/09/2015 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1203014460 Hyper Red APT2012LSECK/J3-PRV
SPEC NO: DSAN8393 REV NO: V.2A DATE: MAR/09/2015 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1203014460 APT2012LSECK/J3-PRV Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm)
SPEC NO: DSAN8393 REV NO: V.2A DATE: MAR/09/2015 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1203014460 Terms and conditions for the usage of this document 1. The information included in this document reflects repr esentative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications . If customer's application ha s special reliability requirements or have lif e-threatening liabilities, such as automot ive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes PACKING & LABEL SPECIFICATIONS APT2012LSECK/J3-PRV