APSE2R5E CHEMI-CON | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Product specifi cations in this catalog are subject to change without notice.Request our product specifi cations before purchase and/or use. Please use our products based on the information contained in this catalog and product specifi cations. CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS ˔Super low ESR, high ripple current capability ˔Downsized from PSC series (П8ʷ8L to П6.3ʷ8L) ˔Endurance is longer life than PSC series (5,000 hours at 105ˆ) ˔ESR after endurance is specified within the initial spec ˔Rated voltage range : 2.5 to 6.3Vdc ˔RoHS Compliant ˔Halogen Free ˗SPECIFICATIONS (at 20ˆ, 120Hz) (at 105ˆ) (at 20ˆ after 2 minutes) (at 20ˆ, 120Hz) (at 100kHz) Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current *Note Dissipation Factor (tan Low Temperature Characteristics (Max.Impedance Ratio) Endurance Bias Humidity Test Surge Voltage Test Failure Rate Items -55 to +105ˆ 2.5 to 6.3Vdc ʶ20% (M) Rated voltage(V)ʷ1.15 I=0.2CV or 500A, whichever is greater Where, I : Max. leakage current (A), C : Nominal capacitance (F), V : Rated voltage (V) 0.10 max. Z(-25ˆ)/Z(+20ˆ)ʽ1.15 Z(-55ˆ)/Z(+20ˆ)ʽ1.25 The following specifications shall be satisfied when the capacitors are restored to 20ˆafter the rated voltage is applied for 5,000 hours at 105ˆ. Appearance No significant damage Capacitance change ʽʶ20% of the initial value D.F. (tan Ў) ʽThe initial specified value ESR ʽThe initial specified value Leakage current ʽThe initial specified value The following specifications shall be satisfied when the capacitors are restored to 20 ˆafter subjecting them to DC voltage at 60 $, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change ʽʶ20% of the initial value D.F. (tan Ў) ʽThe initial specified value ESR ʽThe initial specified value Leakage current ʽThe initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105 ˆ for 30 seconds through a protective resistor(R=1k Њ) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change ʽʶ20% of the initial value D.F. (tan Ў) ʽThe initial specified value ESR ʽThe initial specified value Leakage current ʽThe initial specified value 0.5% per 1,000 hours maximum (Confidence level 60% at 105ˆ) Characteristics ˗DIMENSIONS [mm] ˗MARKING *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105ˆ. Size code ПD Пd F ПD' F08 6.3 2.5 0.6 ПD+0.5max. L+1.5max. H06 8.0 3.5 Coated Case L' 15min. 4min. ПD' Пd Fʶ0.5 Coated Case L' 15min. 4min. ПD' Пd Fʶ0.5 F08 H06 E 6D6 820 2.5V EX) 2.5V820.F ˔Terminal Code : E Longer life Downsized PSE PSC Radial Lead CAT. No. E1001L(1/2)
Product specifi cations in this catalog are subject to change without notice.Request our product specifi cations before purchase and/or use. Please use our products based on the information contained in this catalog and product specifi cations. CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS ˗PART NUMBERING SYSTEM Supplement code Size code Capacitance tolerance code Capacitance code (ex. 820F:821) Lead forming·Taping code Terminal code Voltage code (ex. 2.5V:2R5, 4V:4R0, 6.3V:6R3) Series code Category A P S E 2 R 5 E A A 5 6 1 F 0 8 SM ˗STANDARD RATINGS ˘˘ : Enter the appropriate lead forming or taping code. WV(Vdc) Cap( F) Case size ПDʷL(mm) ESR (mЊ max./20ˆ, 100k to 300kHz) Rated ripple current (mArms/105ˆ, 100kHz) Part No. 2.5 680 8 ×6 APSE2R5E˘˘681MH06S4,9008 820 6.3 ×8 APSE2R5E˘˘821MF08S5,0007 4 560 6.3 ×8 APSE4R0E˘˘561MF08S5,0007 6.3 470 6.3 ×8 APSE6R3E˘˘471MF08S4,7008 560 6.3 ×8 APSE6R3E˘˘561MF08S4,7008 Please refer to "Product code guide (conductive polymer type)" 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Radial Lead CAT. No. E1001L(2/2)