APMA250ARA220MF35S

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 3

Technical content

No.824S/Jul.2015 Conductive Polymer Aluminum Solid Capacitors Please contact us for mass production schedule. Specifications in this bulletin are subject to change without notice. NIPPON CHEMI-CON CORPORATION 1777 1 PMASeriesNPCAP TM ◆SPECIFICATIONS (at 20℃, 120Hz) (at 20℃, 120Hz) (at 105℃) (at 20℃ after 2 minutes) (at 100kHz) Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current Dissipation Factor (tanδ) Low Temperature Characteristics (Max. Impedance Ratio) Damp Heat (Steady State) Endurance Surge Voltage Failure Rate Items -55 to +105℃ 16 to 25Vdc ±20% (M) Rated voltage×1.15V Shall not exceed values shown in STANDARD RATINGS. 0.12 max. The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 5,000 hours at 105℃. Appearance No significant damage Capacitance change ≦±20% of the initial value DF (tanδ) ESR Leakage current ≦The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 500 hours at 60℃, 90 to 95% RH without voltage applied. Appearance No significant damage Capacitance change ESR Leakage current The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105 ℃ for 30 seconds through a protective resistor(R=1k Ω) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change ESR Leakage current 0.5% per 1,000 hours maximum (Confidence level 60% at 105℃) Characteristics ◆DIMENSIONS [mm] ◆MARKING ◆PART NUMBERING SYSTEM EX) 25V15µF *Note : If any doubt arises, measure the leakage current after following voltage treatment. Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105℃. Supplement code Size code Capacitance tolerance code Capacitance code (ex. 15µF:150, 220µF:221) Taping code Terminal code Voltage code (ex. 16V:160, 25V:250) Series code Category A P MA A R A SM 1 34 2 6 7 8 9 10 13125 18171611 1514 ≦±20% of the initial value ≦The initial specified value ≦±20% of the initial value ≦The initial specified value DF (tanδ) DF (tanδ)

• Super low ESR, impedance and high heat resistance have been obtained by using
• Endurance : 105℃ 5,000 hours conductive polymer as electrolyte. ≦200% of the initial specified value ≦200% of the initial specified value ≦200% of the initial specified value ≦200% of the initial specified value ≦200% of the initial specified value ≦200% of the initial specified value NIPPON CHEMI-CON CORPORATION 1595 Engineering Bulletin Conductive Polymer Aluminum Solid CapacitorsNo.824C / Oct.2012 Tentative Specifications in this bulletin are subject to change without notice. Please ask us for technical specifications before purchase and use. A 7.0±0.1 B 7.0±0.1 C 7.2±0.1 L 4.0Max W 1.4±0.2 P 2.65±0.1 Size Code F40 F60 A1DK 25V L A W B P C
• Rated voltage range : 16 to 25Vdc, Capacitance range : 15 to 220µF
• Suitable for DC-DC converters, voltage regulators and decoupling applications used to
• RoHS Compliant computer motherboards etc.
• Exterior resin : Flame-retardant epoxy resin(UL94 V-0)
• Halogen free
• Low profile and higher capacitance with the new structure. NPCAP TM PMA Series
• Low profile and higher capacitance with the new structure.
• Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte.
• Endurance : 105℃ 5,000 hours
• Suitable for DC-DC converters, voltage regulators and decoupling applications used on computer motherboards etc.
• Non solvent resistant type
• RoHS Compliant
• Halogen Free
• Exterior resin : Flame-retardant epoxy resin(UL94 V-0) ◆ SPECIFICATIONS Items Characteristics Category Temperature Range -55 to +105℃ Rated Voltage Range 16 to 25Vdc Capacitance Tolerance±20%（M） (at 20℃, 120Hz) Surge Voltage Rated voltage(V) × 1.15 (at 105℃) Leakage Current Shall not exceed values shown in STANDARD RATINGS. (at 20℃ after 2 minutes) Dissipation Factor (tanδ) 0.12 max. (at 20℃, 120Hz) Low Temperature Characteristics (Max. Impedance Ratio) Endurance The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 5,000 hours at 105℃. Appearance No significant damage Capacitance change ≦ ±20％ of the initial value D.F. (tanδ) ≦200％ of the initial specified value ESR ≦200％ of the initial specified value Leakage current ≦The initial specified value Damp Heat (Steady State) The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 500 hours at 60℃, 90 to 95% RH without voltage applied. Appearance No significant damage Capacitance change ≦ -20 to +40％ of the initial value D.F. (tanδ) ≦200％ of the initial specified value ESR ≦200％ of the initial specified value Leakage current ≦The initial specified value Surge Voltage The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds through a protective resistor(R=1kΩ)and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change ≦ ±20％ of the initial value D.F. (tanδ) ≦200％ of the initial specified value ESR ≦200％ of the initial specified value Leakage current ≦The initial specified value Failure Rate 0.5% per 1,000 hours maximum (Confidence level 60% at 105℃) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃. Size Code A B C L W P ◆ MARKING EX) 25V22μF ◆DIMENSIONS ［mm］
• Rated voltage symbol Rated voltage(Vdc) 16 20 25 Symbol C D E
• Capacitance symbol Capacitance code (ex. 22μF:220) A357 E220

No.824S/Jul.2015 Conductive Polymer Aluminum Solid Capacitors Please contact us for mass production schedule. Specifications in this bulletin are subject to change without notice. NIPPON CHEMI-CON CORPORATION 1777 2 NPCAPTM -PMA Series ◆ STANDARD RATINGS WV (Vdc) Cap (μF) Size code Leakage current (μA max./ after 2min.) ESR (mΩ max./20℃ , 100k to 300kHz) Rated ripple current (mArms/105℃ , 100kHz) Part No. 16 56 F35 448 40 2,200 APMA160ARA560MF35S 20 39 F35 390 45 2,100 APMA200ARA390MF35S 25 22 F35 275 50 2,000 APMA250ARA220MF35S

33 F35 412 50 2,000 APMA250ARA330MF35S

◆ RECOMMENDED REFLOW SOLDERING CONDITIONS

• Reflow Profile
• Recommended Solder Land [mm] PMASeriesNPCAP TM ◆STANDARD RATINGS
• Recommended Solder Land(Based on the PX series) [mm]
• Reflow Profile Location of capacitor c ab b Solder land on PC board 217 230 Peak Preheat Peak temperature Time (sec.) Max. period of time over 230℃ Temperature on the top of capacitor Temperature of capacitor terminal and (℃) Max. period of time over 217℃ ◆RECOMMENDED REFLOW SOLDERING CONDITIONS NIPPON CHEMI-CON CORPORATION 1595 Engineering Bulletin Conductive Polymer Aluminum Solid CapacitorsNo.824C / Oct.2012 Tentative Cap (μF) Rated ripple current (mArms/100kHz) Part No. APMA160ARA680MF40S40F40 APMA160ARA151MF60S18F60 APMA160ARA390MF40S 2,200 3,300 2,200 2,700 4,100 2,70040F40 APMA200ARA470MF40S45F40 APMA200ARA151MF60S20F60 APMA160ARA221MF60S 2,100 3,200 3,300 2,600 3,700 4,10018F60 APMA250ARA220MF40S50F40 APMA250ARA560MF60S26F60 APMA250ARA150MF40S 2,000 2,800 2,000 2,400 3,400 2,40050 544 1,200 312 470 1,500 1,760 275 700 187F40 150 150 220 WV (Vdc) Size code Leakage current (µAmax/after 2min.) ESR (mΩmax/ 20℃, 100k to 300kHz) Specifications in this bulletin are subject to change without notice. Please ask us for technical specifications before purchase and use. *1 Tx: Ambient temperature Voltage range(Vdc) Reflow number Preheat Time maintained above 230℃ Peak temp. 16 to 25V 1-cycle only 150℃ to 180 ℃ 120 sec.max. 50 sec.max. 250℃ max. 30 sec.max. 40 sec.max. 2-cycle allowed Time maintained above 217℃ 40 sec.max. Size code a b c F40,F60 1.63.51.9 ◆PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A P M A A R A M F 3 5 S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 22μF:220, 39μF:390) Taping code Terminal code Voltage code (ex. 20V:200, 25V:250) Series code Category Voltage range (Vdc) Preheat Time maintained above 217℃ Time maintained above 230℃ Peak temp. Reflow number 16 to 25V 150 to 180℃ 120 sec. max. 50 sec. max. 40 sec. max. 250℃ max. 1-cycle only 40 sec. max. 30 sec. max. 2-cycles allowed Location of capacitor Location of capacitor Solder land on PC board < PMA Only > < Share with Ta/Al multilayer capacitors (7343 size) > Size code a b c d e f a bb C e e ab b C f d Location of capacitor ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

No.824S/Jul.2015 Conductive Polymer Aluminum Solid Capacitors Please contact us for mass production schedule. Specifications in this bulletin are subject to change without notice. NIPPON CHEMI-CON CORPORATION 1777 3 NPCAPTM -PMA Series ◆ CARRIER TAPE [mm] ◆ REEL DIMENSIONS [mm] ◆ POLARITY ◆ Storage Size Code Quantity (pcs./reel) Quantity (pcs./reel) (mm) F35 1,000 7,000 18 Items Size Code W A B F P t F 1.75±0.1 W Ｃ Φ1.5 0 +0.1 B 引き出し方向 Ｂ 4±0.1 2±0.1 Ｗ Ｆ 1.75±0.1 引き出し方向 Ｃ Φ1.5 0 +0.1 Ｐ Ａ Ｐ Ａ 断面Ｃ－Ｃ’ 断面Ｃ－Ｃ’ Ｆ４０用 Ｆ６０用 0.6以下 0.6以下 t t 4±0.1 2±0.1 F 1.75±0.1 W Ｃ Φ1.5 -0 +0.1 B 引き出し方向Ｐ Ａ 断面Ｃ－Ｃ' Ｆ３５用 0.6以下 t Φ1.5 4±0.1 2±0.1 F 1.75±0.1 W Ｃ Φ1.5 -0 +0.1 B Feed directionＰ Ａ Cross section (Ｃ－Ｃ') Ｆ３５用 0.6max. t Φ1.5 4±0.1 2±0.1 F 1.75±0.1 W Ｃ Φ1.5 -0 +0.1 B Feed directionＰ Ａ Cross section(C-C') Ｆ３５用 0.6max. t Φ1.5 PMASeriesNPCAP TM NIPPON CHEMI-CON CORPORATION 1595 3 Specifications in this bulletin are subject to change without notice. Please ask us for technical specifications before purchase and use. WA B F P t Items Fig. F40 F60 Size Code Quantity (pcs./reel) Quantity (pcs./reel) (mm) Fig.2 φ1. 5 ＋0. 1 t t ◆CARRIER TAPE [mm] Fig.1 ◆REEL DIMENSIONS [mm] ◆POLARITY 4.9 6.7 12.0 16.0 7.5 11.5 8.0 8.0 7.5 7.5 16.0 24.0 7,000 3,000 1,000 500 F40 F60 4±0.1 2±0.05 W A P C F B 0.6max Feed direction Cross section (C-C' ) 2±0.05 W A P Feed direction Cross section (C-C' ) F B 0.6max 1.75±0.1 1.75±0.1 13±0.5 Feed Direction 382max. φ50min. C φ1. 5 ＋0. 1 Engineering Bulletin Conductive Polymer Aluminum Solid CapacitorsNo.824C / Oct.2012 Tentative 4±0.1 PMASeriesNPCAP TM NIPPON CHEMI-CON CORPORATION 1595 3 Specifications in this bulletin are subject to change without notice. Please ask us for technical specifications before purchase and use. WA B F P t Items Fig. F40 F60 Size Code Quantity (pcs./reel) Quantity (pcs./reel) (mm) Fig.2 φ1. 5 ＋0. 1 t t ◆CARRIER TAPE [mm] Fig.1 ◆REEL DIMENSIONS [mm] ◆POLARITY 4.9 6.7 12.0 16.0 7.5 11.5 8.0 8.0 7.5 7.5 16.0 24.0 7,000 3,000 1,000 500 F40 F60 4±0.1 2±0.05 W A P C F B 0.6max Feed direction Cross section (C-C' ) 2±0.05 W A P Feed direction Cross section (C-C' ) F B 0.6max 1.75±0.1 1.75±0.1 13±0.5 Feed Direction 382max. φ50min. C φ1. 5 ＋0. 1 Engineering Bulletin Conductive Polymer Aluminum Solid CapacitorsNo.824C / Oct.2012 Tentative 4±0.1 Store PMA series capacitors in a cool, dry place. Store at a temperature between 5 and 35 ℃ , with a humidity of 75%RH or less. PMA series capacitors are sealed in a special laminated aluminum bag. Use all capacitors once the bag is opened. Return unused capacitors to the bag, and seal it with a zipper. Please refer to the following storage conditions. ・Maximum storage term before the bag is opened :Within 2 years after manufacturing ・Maximum storage condition after the bag is opened : Within 7 days after the bag is opened