APG1005PBC-T-5MAV KINGBRIGHT | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
Features
z 1.0mmX0.5mm SMT LED, 0.2mm thickness. z Low power consumption. z Wide viewing angle. z Compatible with automatic placement equipment. z Ideal for backlight and indicator. z Package: 4000pcs / reel. z Moisture sensitivity level : level 3. z Low current IF=5mA operating. z RoHS compliant. Descriptions z The Blue source color devices are made with InGaN on SiC substrate Light Emitting Diode. z Electrostatic discharge and power surge could damage the LEDs. z It is recommended to use a wrist band or anti- electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES
SPEC NO: DSAN2911 REV NO: V.5B DATE: MAY/06/2015 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013982 Selection Guide Absolute Maximum Ratings at TA=25°C Electrical / Optical Characteristics at TA=25°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. Part No. Dice Lens Type Iv (mcd) [2] @ 5mA Viewing Angle [1] Min. Typ. 2 θ1/2 APG1005PBC-T-5MAV Blue (InGaN) Water Clear 20 28 145° Symbol Parameter Device Typ. Max. Units Test Conditions λpeak Peak Wavelength Blue 461 nm I F=5mA λD [1] Dominant Wavelength Blue 467 nm I F=5mA Δλ1/2 Spectral Line Half-width Blue 22 nm I F=5mA VF [2] Forward Voltage Blue 2.9 3.1 V I F=5mA IR Reverse Current Blue 50 uA V R=5V Parameter Blue Units Power dissipation 32 mW DC Forward Current 10 mA Peak Forward Current [1] 50 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Electrostatic Discharge Threshold (HBM) 1000 V Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure.
SPEC NO: DSAN2911 REV NO: V.5B DATE: MAY/06/2015 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013982 Blue APG1005PBC-T-5MAV
SPEC NO: DSAN2911 REV NO: V.5B DATE: MAY/06/2015 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013982 APG1005PBC-T-5MAV Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm)
SPEC NO: DSAN2911 REV NO: V.5B DATE: MAY/06/2015 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203013982 PACKING & LABEL SPECIFICATIONS APG1005PBC-T-5MAV Terms and conditions for the usage of this document 1. The information included in this docum ent reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the dat asheet. If customer usage exceeds the spec ified limits, Kingbright will not be respon sible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applicati ons. If customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes