DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 17
Technical content
Features
High Voltage CMOS Process, up to 30V (VDD to VM) Low Quiescent Current (+25°C ) In Power-Down Mode, 0.1µA (Max.) High-Accuracy Voltage Detection Circuit (+25°C) Overcharge Detection Voltage: 3.5V to 4.5V (5mV Steps) Accuracy ±25mV Overcharge Hysteresis Voltage Range: 0.1V to 0.4V (50mV Steps) Accuracy ±50mV Overdischarge Detection Voltage: 2.0V to 3.4 V (10mV Steps) Accuracy ±35mV Overdischarge Hysteresis Voltage Range: 0V to 0.7V (40mV Steps) Accuracy ±65mV Discharge Overcurrent Detection Voltage: 0.05V to 0.32V (10mV Steps) Accuracy ±15mV Short Current Detection Voltage: 0.45V to 0.7V (50mV Steps) Accuracy ±100mV Charge Overcurrent Detection Voltage: -0.2V to -0.05V (10mV Steps) Accuracy ±15mV Overcharger Detection Voltage: 8.0V (Fixed) Accuracy ±2V Overcharger Release Voltage: 7.3V (Fixed) Accuracy ±2V Built-in Fixed Detection Delay Time (+25°C ), Accuracy ±20% Power-Down Mode Selectable (Yes or No) 0V Battery Charge Selectable (Permission or Inhibition) Overcharge Protection Mode Selectable (Auto Release or Latch) Totally Lead-free & Fully RoHS Compliant (Notes 1 & 2) Halogen and Antimony Free. “Green” Device (Note 3) Pin Assignments (Top View) VSS VDD VM NC EP U-DFN2030-6
Applications
Li+ Rechargeable Battery Pack Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. 2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen - and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds.
Document number: DS37596 Rev. 2 - 2 2 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Typical Applications Circuit (Note 4) AP9211 (U-DFN2030-6)BAT 100n 2.7kohm VDD VSS S1 S2 VM 330ohm to 470ohm Note: 4. R1 and C1 are used to stabilize the supply voltage of the AP9211. The recommended range of R1 value is 330Ω to 470Ω and C1 value is 10nF to 1000nF, typical value is 100nF. R2 should be connected between P- to VM sense terminal to monitor the status of charger and the charge/discharge current. The R2 should be b etween 300Ω and 4kΩ, typical value is 2.7kΩ. R1 and R2 are also used as current limit resistors if the battery or charger is connected reversely. Polarity reversing may cause the power consumption of R1 and R2 t o go over their power dissipation rating, the refore R1 and R2 values should be selected appropriately for the actual application. If R2 is more than 4kΩ resistor, charge may not be off due to the voltage drop on R2. For power down mode, w hen first connecting AP9 211 system board to the battery, it is necessary to use charger or to short P - to the battery negative polarity. Once the AP9 211 is activated, the charger or connection can be removed, otherwise the battery cannot discharge current through system board. The values selected sho uld follow the recommended typical range mentioned above. It has not been confirmed whether the operation is normal or not in circuits other than the above example of connection. In addition, the example of connection shown above and the typical value do n ot exactly guarantee proper operation. Please perform the actual application to set the suitable value through your complete evaluation. Pin Descriptions Pin Number Pin Name Function 1 S1 Source pin of discharging MOSFET, connecting this pin to battery negative pole.
2 VSS Negative power supply pin
3 VDD Positive power supply pin, connecting this pin to battery positive pole through R1
4 NC Not connected, leave this pin floating
5 VM Charger negative input pin, short this pin to S2 pin through R2
6 S2 Source pin of charging MOSFET, connecting this pin to charge negative input. EP D Thermal PAD is common drain of charge and discharge MOSFET, so in PCB layout, prefer to use large copper area to cover this pad for better thermal dissipation, then leave it open.
Document number: DS37596 Rev. 2 - 2 3 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Functional Block Diagram Logic Circuit Logic Circuit Delay Time Circuit OV Charge Option Level Shift RVMD RVMS S1 S2D2D1 G1 G2 VDD VSS S2S1 VM D EP
Document number: DS37596 Rev. 2 - 2 4 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Absolute Maximum Ratings (Notes 5 & 6) Symbol Parameter Rating Unit VDS Supply Voltage (Between VDD and VSS) -0.3 to 12 V VDM Charge Input Voltage (Between VDD and VM for Protection Chip) -0.3 to 24 V VDSS MOSFET Drain-to-Source Voltage 24 V VGSS MOSFET Gate-to-Source Voltage ±12 V ID Continuous Drain Current, VGS = 4.5V, TA = +25°C 9.0 A Continuous Drain Current, VGS = 4.5V, TA = +70°C 7.1 A PD Power Dissipation 1,000 mW TJ Maximum Junction Temperature +150 °C TSTG Storage Temperature Range -65 to +150 °C — ESD (Machine Model) 300 V — ESD (Human Body Model) 3,000 V Notes: 5. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these conditions is not implied. Exposure to absolute -maximum-rated conditions for extended periods may affect device reliability. 6. Ratings apply to ambient temperature at +25°C. The JEDEC High -K board design used to derive this data was a 2 inch x 2 inch multilayer board with 2- ounce internal power and ground planes and 2-ounce copper traces on the top and bottom of the board. Recommended Operating Conditions Symbol Parameter Min Max Unit VDS Supply Voltage (Between VDD and VSS) 1.5 5.5 V VDM Charge Input Voltage (between VDD and VM) -0.3 5.5 V TA Operating Ambient Temperature -40 +85 °C
Document number: DS37596 Rev. 2 - 2 5 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Electrical Characteristics (TA = +25°C, VDD = 3.5V, VSS = 0V, R1 = 220Ω, R2 = 1.0kΩ, C1 = 100nF, unless otherwise specified) Symbol Parameter Conditions Min Typ Max Units VCU Overcharge Detection Voltage － VCU - 0.025 VCU VCU + 0.025 V VCL Overcharge Release Voltage VCL ≠ VCU VCL - 0.050 VCL VCL + 0.050 V VCL = VCU VCL - 0.025 VCL VCL + 0.025 V VDL Overdischarge Detection Voltage － VDL - 0.035 VDL VDL + 0.035 V VDU Overdischarge Release Voltage VDU ≠ VDL VDU - 0.100 VDU VDU + 0.100 V VDU = VDL VDU - 0.035 VDU VDU + 0.035 V VDOC Discharge Overcurrent Detection Voltage － VDOC -0.015 VDOC VDOC +0.015 V VSHORT Load Short-Circuiting Detection Voltage － VSHORT -0.10 VSHORT VSHORT +0.10 V VCOC Charge Overcurrent Detection Voltage － VCOC -0.015 VCOC VCOC +0.015 V ICC Current Consumption During Operation VDD=3.5V VM=0V 1.5 3.0 4.5 μA ISTB Current Consumption at Power Down VDD=1.8V VM Pin Floating Power Down Mode － － 0.1 μA Without Power Down Mode (Auto Wake up) － － 5.5 μA RVMD Resistance Between VM Pin and VDD Pin VDD=1.8V VM=0V 150 300 500 kΩ RVMS Resistance Between VM Pin and VSS Pin VDD=3.5V VM=1.0V 10 30 50 kΩ V0CHA 0V Battery Charge Starting Charge Voltage 0V battery charging “available” 1.2 － － V V0INH 0V Battery Charge Inhibition Battery Voltage 0V battery charging “unavailable” － － 0.45 V VOVCHG Overvoltage Charge Detection Voltage VDD=3.5V 6.0 8.0 10.0 V VOVCHGR Overvoltage Charge Release Voltage VDD=3.5V 5.3 7.3 9.3 V tCU Overcharge Detection Delay Time － tCU * 0.8 tCU tCU * 1.2 ms tCUR Overcharge Release Delay Time － tCUR * 0.8 tCUR tCUR * 1.2 ms tDL Overdischarge Detection Delay Time － tDL * 0.8 tDL tDL * 1.2 ms tDLR Overdischarge Release Delay Time － tDLR * 0.8 tDLR tDLR * 1.2 ms tDOC Discharge Overcurrent Detection Delay Time － tDOC * 0.8 tDOC tDOC * 1.2 ms tDOCR Discharge Overcurrent Release Delay Time － tDOCR * 0.8 tDOCR tDOCR * 1.2 ms tSHORT Load Short Detection Delay Time － tSHORT * 0.8 tSHORT tSHORT * 1.2 μs tCOC Charge Overcurrent Detection Delay Time － tCOC * 0.8 tCOC tCOC * 1.2 ms tCOCR Charge Overcurrent Release Delay Time － tCOCR * 0.8 tCOCR tCOCR * 1.2 ms
Document number: DS37596 Rev. 2 - 2 6 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Electrical Characteristics (continued) (TA = -40°C to +85°C, VDD = 3.5V, VSS = 0V, R1 = 220Ω, R2 = 1.0kΩ, C1 = 100nF, unless otherwise specified) Symbol Parameter Conditions Min Typ Max Units VCU Overcharge Detection Voltage － VCU - 0.060 VCU VCU + 0.040 V VCL Overcharge Release Voltage VCL ≠ VCU VCL - 0.080 VCL VCL + 0.065 V VCL = VCU VCL - 0.060 VCL VCL + 0.040 V VDL Overdischarge Detection Voltage － VDL - 0.080 VDL VDL + 0.080 V VDU Overdischarge Release Voltage VDU ≠ VDL VDU - 0.150 VDU VDU + 0.190 V VDU = VDL VDU - 0.080 VDU VDU + 0.080 V VDOC Discharge Overcurrent Detection Voltage － VDOC -0.021 VDOC VDOC +0.024 V VSHORT Load Short-Circuiting Detection Voltage － VSHORT -0.34 VSHORT VSHORT +0.34 V VCOC Charge Overcurrent Detection Voltage － VCOC -0.040 VCOC VCOC +0.040 V ICC Current Consumption During Operation VDD=3.5V VM=0V 1.0 3.0 7.0 μA ISTB Current Consumption at Power Down VDD =1.8V VM Pin Floating Power Down Mode － － 1.0 μA Without Power Down Mode (Auto Wake up) － － 8 μA RVMD Resistance between VM Pin and VDD Pin VDD=1.8V VM=0V 100 300 650 kΩ RVMS Resistance between VM Pin and VSS Pin VDD=3.5V VM=1.0V 5 30 65 kΩ V0CHA 0V Battery Charge Starting Charge Voltage 0V battery charging “available” 1.2 － － V V0INH 0V Battery Charge Inhibition Battery Voltage 0V battery charging “unavailable” － － 0.3 V VOVCHG Overvoltage Charge Detection Voltage VDD=3.5V 5.5 8.0 10.5 V VOVCHGR Overvoltage Charge Release Voltage VDD=3.5V 5.0 7.3 9.5 V tCU Overcharge Detection Delay Time － tCU * 0.6 tCU tCU * 1.4 ms tCUR Overcharge Release Delay Time － tCUR * 0.6 tCUR tCUR * 1.4 ms tDL Overdischarge Detection Delay Time － tDL * 0.6 tDL tDL * 1.4 ms tDLR Overdischarge Release Delay Time － tDLR * 0.6 tDLR tDLR * 1.4 ms tDOC Discharge Overcurrent Detection Delay Time － tDOC * 0.6 tDOC tDOC * 1.4 ms tDOCR Discharge Overcurrent Release Delay Time － tDOCR * 0.6 tDOCR tDOCR * 1.4 ms tSHORT Load Short Detection Delay Time － tSHORT * 0.6 tSHORT tSHORT * 1.4 μs tCOC Charge Overcurrent Detection Delay Time － tCOC * 0.6 tCOC tCOC * 1.4 ms tCOCR Charge Overcurrent Release Delay Time － tCOCR * 0.6 tCOCR tCOCR * 1.4 ms
Document number: DS37596 Rev. 2 - 2 7 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Electrical Characteristics (continued) (Notes 7 & 8) (TA = +25°C, VDD = 3.5V, VSS = 0V, R1 = 220Ω, R2 = 1.0kΩ, C1 = 100nF, unless otherwise specified) Symbol Parameter Conditions Min Typ Max Units IDSS Zero Gate Voltage Drain Current VDS = 20V, VGS=0 – – 1.0 μA RSS(ON)1 Static Source-Source On-Resistance 1 VDD = 4.0V ID = 1.0A 20 27 30 mΩ RSS(ON)2 Static Source-Source On-Resistance 2 VDD = 3.9V ID = 1.0A 21 27 31 mΩ RSS(ON)3 Static Source-Source On-Resistance 3 VDD = 3.0V ID = 1.0A 21 28 33 mΩ VSD Diode Forward Voltage VGS = 0V (Note 6) IS = 1A – 0.75 1.0 V Notes: 7. In case of Gate-Source voltage of charging MOSFET is 0V. In case of Gate-Source voltage of discharging MOSFET is 0V. 8. These specifications are guaranteed by design - will not be tested in production.
Document number: DS37596 Rev. 2 - 2 8 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211
Application Information
- Normal Status The AP9211 monitors the battery voltage between the V DD pin and V SS pin as well as the voltage difference between the V M pin and V SS pin to control battery charging and dischar ging. When the battery voltage is between overdischarge detection voltage (V DL) and overcharge detection voltage (V CU) as well as the V M pin voltage is between th e charge overcurrent detection voltage (V COC) and discharge overcurrent detection voltage (VDOC), the AP9211 will turn on discharging and charging MOSFET. In these conditions, the battery can charge and discharge freely. Also, RVMD does not connect to VDD pin and RVMS does not connect to VSS pin in this status. 2. Overcharge Status If the battery voltage is more than V CU during charging status for the overcharge detection delay time (t CU) or longer, the AP9211 turns off the charging MOSFET to stop charging. RVMD and RVMS are not connected in overcharge status. When VM pin voltage is lower than VDOC and battery voltage falls below VCL, the AP9211 will release from overcharge status. When VM pin voltage is equal or more than VDOC and battery voltage falls below VCU, the AP9211 will release from overcharge status. 3. Overdischarge Status If the battery voltage is less than V DL during discharging status for the overdischarge detection delay time (tDL) or longer, the AP9211 turns off the discharging MOSFET to stop discharging. In overdischarge status, RVMD is connected to VDD and VM pin voltage is pulled u p to VDD by RVMD, but RVMS is not connected. For power-down mode version, the AP9211 recovers normal status from overdischar ge status only by charging the battery through the charger. When VM pin voltage to V SS pin voltage is less than typical -0.7V and the battery voltage rises over V DL, the AP9211 will release from overdischarge status. If VM pin voltage to VSS pin voltage is higher than typical -0.7V, the AP9211 will release from overdischarge status until the battery voltage rises over VDU. For auto-wake-up version AP9211SA, the device recovers to normal status from overdischarge status if either of these two conditions are satisfied: If charger is connected: the AP9211SA overdischarge status is released in the same way as described above in AP9211S Overdischarge Status section. If no charger is connected: 1) The battery voltage reaches the overdischarge release voltage (VDU) or higher; 2) Maintains continuous time more than overdischarge release delay time tDLR. 4. Discharge Overcurrent and Short Current Status When battery is in discharge overcurrent status, if the voltage of the VM pin to VSS pin is equal or more than VDOC to VSHORT and detection lasts for the discharge overcurrent detection delay time (tDOC) or longer, the AP9211 turns off the discharging MOSFET to stop discharging. When the battery is in short current status, if the voltage of the V M pin to VSS pin is equal to or more than V SHORT, and the detection lasts for the short current detection delay time or longer, the AP9211 turns off the discharge MOSFET to stop discharging. In discharge overcurrent or short current status, RVMS is connected to VSS but RVMD is not connected. The voltage of VM pin is almost equal to VDD as long as the load is connected. When the load is disconnected, the voltage of V M pin will become almost equal to V SS (due to R VMS being connected) and then the AP9211 will release from discharge overcurrent or short current status. 5. Charge Overcurrent Status When the battery is in charge current status, if the voltage of the VM pin to VSS pin is equal to or less than VCOC and the detection continues for the charge overcurrent detection delay time (tCOC) or longer, the AP9211 turns off the charging MOSFET to stop charging. 6. 0V Battery Charging Function (Option) This function is available as an option and can be factory set internally. AP9211 has this function built in. 0V charging function permits charger to recharge the battery whose voltage is 0V due to self-discharge. If 0V charging function is not present, the device will prevent charger to recharge the battery whose voltage is 0V due to self-discharge. (If a device without 0V charging function is needed, please contact Diodes sales team)
Document number: DS37596 Rev. 2 - 2 9 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Operation Description (Continued) 7. Overvoltage Charger Detection Circuit This function is used to monitor the charger voltage between the VDD pin and VM pin, and when this voltage exceeds overvoltage charger detection voltage (8.0V Typ.), the AP9211 will turn off charging MOSFET, when this voltage drops below overvoltage charger release voltage (7.3V Typ.), it then turns on charging MOSFET. There are no delay times set for detection and release. 8. Power-Down Mode or Auto-Wake-Up Function Option In device with power-down function, during power-down mode, device enters the overdischarge status. The IC enters sleep mode and the current consumption becomes very low, typically 0.1µA. To release from power-down status to the normal status, charger connection is required. In device with auto-wakeup mode, the IC remains active in the overdischarge state. The IC is released into the normal state by the operation that increases the battery voltage more than overdischarge release voltage.
Document number: DS37596 Rev. 2 - 2 10 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Application Information (Timing Chart) 1. Overcharge and Overdischarge Detection VCU VCL VDL VDU VDD VSS VSS VDD VVM VDD VDOC VSS VP- VCOC VDD DO CO VM 2 1 Red line is for no shutdown mode version 1: tDL 2: tCU 3: tCUR 4: tDLR 2 1 S1 S1 S2S2 3 4 3 3 S1: Charger connection S2: Load connection P1: RVMD pull-up connection P1 P1
Document number: DS37596 Rev. 2 - 2 11 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Application Information (Timing Chart) (continued) 2. Discharge Overcurrent Detection VCU VCL VDL VDU ON VSS OFF ON OFF VDD VSHORT VSS VDOC VDD Discharge FET Charge FET VM 1 2 S1 S2 1: tDOC 2: tSHORT 3: tDOCR S1: Connect over current load S2: Connect short current load P1: RVMS pull-down connection 3 3
Document number: DS37596 Rev. 2 - 2 12 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Application Information (Timing Chart) (cont.) 3. Charge Overcurrent Detection VCU VCL VDL VDU VDD VSS VSS VDD VVM VDD VSS VP- VCOC VDD Discharge FET Charge FET VM 1: tCOC 2: tCOCR S1: Connect over current charger
Document number: DS37596 Rev. 2 - 2 13 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Ordering Information (Note 9) AP9211X X - XX - XXX - X Product Code Voltage & Delay Time Combination Code HAC: U-DFN2030-6 Packing 7: Tape & Reel Power Down Mode Blank: Yes A: No (Auto-wake-up) Package S: Standard RSS(ON) Part Number Package Code Packaging 7” Tape and Reel Quantity AP9211XX-XX-HAC-7 HAC U-DFN2030-6 3,000/Tape & Reel Voltage Combination Part Number Overcharge Detection Voltage VCU Overcharge Release Voltage VCL Over- discharge Detection Voltage VDL Over- discharge Release Voltage VDU Discharge Overcurrent Detection Voltage VDOC Load Short Detection Voltage VSHORT Charge Overurrent Detection Voltage VCOC Over Voltage Charger Detection Voltage VOVCHG Over Voltage Charger Release Voltage VOVCHGR Power-down Function Overcharge Protection Mode Delay Time 0V Battery Charge Function Selectable Auto Release Option 1 Permission Selectable Auto Release Option 1 Permission Selectable Auto Release Option 1 Permission Selectable Auto Release Option 1 Permission Selectable Auto Release Option 1 Permission Selectable Auto Release Option 1 Permission Selectable Auto Release Option 1 Permission Selectable Auto Release Option 1 Permission Selectable Auto Release Option 1 Permission Selectable Auto Release Option 1 Permission Selectable Auto Release Option 1 Permission Selectable Auto Release Option 1 Permission Note: 9. Current voltage versions are built by delay time option 1. If any other voltage versions or delay time option products are needed, please con tact with the local sale’s office.
Document number: DS37596 Rev. 2 - 2 14 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Ordering Information (Note 7, continued) AP9211 Delay Time Combination Part Number Overcharge Detection Delay Time tCU Overcharge Release Delay Time tCUR Overdischarge Detection Delay Time tDL Overdischarge Release Delay Time tDLR Discharge Overcurrent Detection Delay Time tDOC Discharge Overcurrent Release Delay Time tDOCR Charge Overcurrent Detection Delay Time tCOC Charge Overcurrent Release Delay Time tCOCR Load Short Detection Delay Time tSHORT Other Delay Time Combination Table (Optional) Delay Time Option Overcharge Detection Delay Time (tCU) Overdischarge Detection Delay Time (tDL) Discharge Over Current Detection Delay Time (tDOC) Charge Over Current Detection Delay Time (tCOC) Load Short Circuiting Detection Delay Time (tSHORT) 1 1s 115ms 10ms 10ms 360µs 2 125ms 32ms 8ms 8ms 180µs 3 1s 20ms 12ms 10ms 360µs 4 1s 42ms 10ms 10ms 360µs 5 1s 115ms 10ms 10ms 180µs
Document number: DS37596 Rev. 2 - 2 15 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Marking Information Y : Year : 0~9 (Top View) X : A~Z : Internal Code Y W X XX XX : Identification Code W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week Part Number Package Identification Code AP9211S-AA-HAC-7 U-DFN2030-6 P5 AP9211S-AB-HAC-7 U-DFN2030-6 P6 AP9211S-AC-HAC-7 U-DFN2030-6 6B AP9211S-AD-HAC-7 U-DFN2030-6 6C AP9211S-AE-HAC-7 U-DFN2030-6 6D AP9211S-AF-HAC-7 U-DFN2030-6 6E AP9211S-AG-HAC-7 U-DFN2030-6 6F AP9211S-AH-HAC-7 U-DFN2030-6 6G AP9211S-AI-HAC-7 U-DFN2030-6 6H AP9211S-AJ-HAC-7 U-DFN2030-6 6Y AP9211S-AK-HAC-7 U-DFN2030-6 6Z AP9211S-AL-HAC-7 U-DFN2030-6 5T AP9211S-AM-HAC-7 U-DFN2030-6 5U AP9211S-AN-HAC-7 U-DFN2030-6 5V AP9211SA-AA-HAC-7 U-DFN2030-6 M3 AP9211SA-AB-HAC-7 U-DFN2030-6 M4 AP9211SA-AC-HAC-7 U-DFN2030-6 M6 AP9211SA-AD-HAC-7 U-DFN2030-6 M7 AP9211SA-AE-HAC-7 U-DFN2030-6 M8 AP9211SA-AF-HAC-7 U-DFN2030-6 N3 AP9211SA-AG-HAC-7 U-DFN2030-6 N4 AP9211SA-AH-HAC-7 U-DFN2030-6 N6 AP9211SA-AI-HAC-7 U-DFN2030-6 N7 AP9211SA-AJ-HAC-7 U-DFN2030-6 N8 AP9211SA-AK-HAC-7 U-DFN2030-6 NE AP9211SA-AL-HAC-7 U-DFN2030-6 7X AP9211SA-AM-HAC-7 U-DFN2030-6 P7 AP9211SA-AN-HAC-7 U-DFN2030-6 P8
Document number: DS37596 Rev. 2 - 2 16 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 Package Outline Dimensions Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. A Seating Plane D E bb2 z R0.150 L Pin1 ID e1 e1 U-DFN2030-6 (Type C) Dim Min Max Typ A 0.50 0.60 -- A1 0.00 0.05 0.02 A3 -- -- 0.127 b 0.25 0.35 0.30 b2 0.60 0.70 0.65 D 1.90 2.10 2.00 D2 1.60 1.80 1.70 E 2.90 3.10 3.00 E2 1.60 1.80 1.70 e -- -- 0.60 e1 -- -- 0.775 L 0.25 0.35 0.30 z 0.0500 Ref All Dimensions in mm Suggested Pad Layout Please see AP02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version. X1 X C1 C G Y Dimensions Value (in mm) C 0.600 C1 0.775 G 0.200 G1 0.200 X 0.400 X1 0.750 X2 1.800 Y 0.500 Y1 1.800
Document number: DS37596 Rev. 2 - 2 17 of 17 www.diodes.com December 2015 © Diodes Incorporated AP9211 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product descr ibed herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license unde r its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diod es Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any u nintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising ou t of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or system s without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided i n the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support d evices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety -critical, life support devices or systems, notwithstanding any devices - or systems -related information or suppo rt that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2015, Diodes Incorporated www.diodes.com