Power Management

AP7583Q

Diodes Incorporated

WIDE INPUT VOLTAGE RANGE, 300mA ULDO REGULATOR WITH PG December 2022 Rev. 1 - 2

Manufacturer: Diodes Incorporated

Document: 21 Pages / 1Mb

Request Quote Download Datasheet Read online HTML view

More from Diodes Incorporated Browse A parts

Online Datasheet

Read AP7583Q online.

AP7583Q DIODES | Alldatasheet

Document overview

Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
PDF pages: 21

Technical content

Features

 Wide Input-Voltage Range: 3V to 42V  Maximum Output Current: 300mA  Low-Dropout Voltage: VDROP = 320mV @IOUT = 300mA (Typ)  Low Quiescent Current:  AP7583Q is 2.5μA (Typ)  AP7583AQ is 3μA (Typ)  High Output-Voltage Accuracy: ±1.5%  Compatible with Low ESR Ceramic Capacitor  Excellent Line/Load Regulation  Thermal Shutdown Function  Short Current Protection Function  Output Current Limit  AP7583AQ with Power-Good (PG) Output for Supply Monitoring and for Sequencing of Other Supplies  Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)  Halogen and Antimony Free. “Green” Device (Note 3)  The AP7583Q/AQ are suitable for automotive applications requiring specific change control; these parts are AEC-Q100 qualified, PPAP capable, and manufactured in IATF16949 certified facilities. https://www.diodes.com/quality/product-definitions/

Applications

 Powering MCUs and CAN/LIN transceivers  Automotive head units  EV and HEV battery management systems  Body control modules  Transmission control units (TCU) Pin Assignments FB/NC EN PG(AQ) VIN MSOP-8EP (Top View) NC GND GND VOUT EP VIN EN GND VOUT NC(Q) / PG(AQ) FB/NC (Top View) W-DFN2020-6 SWP Type A1 EP Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 20 15/863/EU (RoHS 3) compliant. 2. See https://www.diodes.com/quality/lead-free/ for more information about Diodes Incorporated’s definitions of Halogen - and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds. AP7583AQ AP7583AQ AP7583Q/AQ Future Product W-DFN2020-6 (SWP) (Type A1)

Document number: DS43764 Rev. 1 - 2 2 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Typical Applications Circuit COUT AP7583Q Fixed Version CIN VIN GND EN VOUT Enable VIN VOUT AP7583Q COUT AP7583AQ Fixed Version CIN VIN GND EN VOUT Enable VIN VOUT AP7583AQ PG VPG CIN VIN GND EN VOUT Enable ADJ R1 COUT VIN VOUT AP7583Q AP7583Q Adjustable Output CIN VIN GND EN VOUT Enable ADJ R1 COUT VIN VOUT AP7583AQ AP7583AQ Adjustable Output PG VPG Pin Descriptions Pin Number Pin Name Function MSOP-8EP AP7583AQ W-DFN2020-6 (SWP) (Type A1) AP7583Q/AQ TO252-4 (Type C) AP7583AQ 1 1 1 VIN Input voltage 2 2 2 EN Enable input, active high 3 5(Q) — NC Not connected internally. Recommend connection to GND to maximize PCB copper for thermal dissipation. 7 5(AQ) 4 PG Power-Good pin with one internal pull high resistor. When the VOUT is below the PG threshold, the PG pin is driven low; when the VOUT exceeds the threshold, the PG pin goes into a high-impedance state. 4, 5 3 3 GND Ground 6 4 — FB/NC Adjustable voltage version only – a resistor divider from this pin to the OUT pin and ground sets the output voltage. 8 6 5 VOUT Regulated output voltage EP EP — Exposed Pad In PCB layout, prefer to use large copper area to cover this pad for better thermal dissipation, then connect this area to GND or leave it open. However, do not use it as GND electrode function alone.

Document number: DS43764 Rev. 1 - 2 3 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Functional Block Diagram VIN EN GND VOUT Gate Driver 0.8V Current Limit and Thermal Shutdown AP7583Q Fixed Version with EN VIN EN GND VOUT Gate Driver 0.8V Current Limit and Thermal Shutdown AP7583Q Adjustable Version FB VIN EN GND VOUT Gate Driver 0.8V Current Limit and Thermal Shutdown AP7583AQ Adjustable Version 0.72V PG FB RPU VOUT VIN EN GND VOUT Gate Driver 0.8V Current Limit and Thermal Shutdown AP7583AQ Fixed Version 0.72V PG RPU VOUT

Document number: DS43764 Rev. 1 - 2 4 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Absolute Maximum Ratings (Note 4) (@TA = +25° C, unless otherwise specified.) Symbol Parameter Rating Unit VIN Supply Input Voltage -0.3 to 45 V VOUT Regulated Output Voltage -0.3 to 7 V IOUT Output Current 300 mA TLEAD Lead Temperature (Soldering, 10sec) +260 ºC TJ Operating Junction Temperature +150 ºC θJA Thermal Resistance (Junction to Ambient) MSOP-8EP 36.1 ° C/W W-DFN2020-6 (SWP) (Type A1) 80.4 TO252-4 (Type C) 27.2 θJC Thermal Resistance (Junction to Case) MSOP-8EP 6.532 ° C/W W-DFN2020-6 (SWP) (Type A1) 26.4 TO252-4 (Type C) 7.5 TSTG Storage Temperature Range -40 to +150 °C CDM ESD (Change Device Model) ±1500 V HBM ESD (Human Body Model) ±2000 V Notes: 4. a). Stresses beyond those listed under Absolute Maximum Ratings can cause permanent damage to the device. These are stress ratings only and functional operation of the device at these conditions is not implied. Exposure to absolute-maximum-rated conditions for extended period can affect device reliability. b). Ratings apply to ambient temperature at +25° C. The JEDEC STD.51 High-K board design used to derive this data was a 3inch × 3inch multilayer board with 1oz. internal power and ground planes and 2oz. copper traces on the top and bottom of the board. Recommended Operating Conditions Symbol Parameter Min Max Unit VIN Supply Input Voltage 3.0 42 V VOUT Supply Output Voltage 1.2 5 V TJ Operating Junction Temperature -40 +125 °C

Document number: DS43764 Rev. 1 - 2 5 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Electrical Characteristics (-40° C ≤ TJ ≤ +125° C, IOUT = 1mA, CIN = COUT = 10µF ceramic capacitor, VIN = 14V) Symbol Parameter Test Conditions Min Typ Max Unit VOUT Output Voltage Variation from Specified VOUT VOUT* 98.5% — VOUT* 101.5% V VIN Input Voltage — 3.0 — 42 V VFB Feedback Reference Voltage — 1.183 1.207 1.231 V ILIMIT Current Limit VOUT Short to 90% x VOUT 310 510 690 mA △VOUT/∆VIN Line Regulation VIN = VOUT + 1V to 40V, IOUT = 1mA -10 — 10 mV △VOUT/VOUT Load Regulation 1mA ≤ IOUT ≤ 300mA -20 — 20 mV VDROP Dropout Voltage (Note 5) IOUT = 300mA @VOUT = 3.3V — 450 700 mV IOUT = 300mA @VOUT = 5V — 320 500 mV IQ Quiescent Current AP7583Q IOUT = 0A — 2.5 4.0 µA AP7583AQ IOUT = 0A — 3 6 µA ISHUTDOWN Shutdown Current EN = 0V — 0.3 0.5 µA VIL EN Input Logic-Low Voltage — 0 — 0.3 V VIH EN Input Logic-High Voltage — 1.7 — VIN V ∆VOUT/(VOUTx∆T) Output Voltage Temperature Coefficient IOUT = 100µ A, -40°C ≤ TJ ≤ +125°C — ± 100 — ppm/°C TOTSD Thermal Shutdown Temperature — — +175 — ° C THYOTSD Thermal Shutdown Hysteresis — — +20 — ° C PSRR Power Supply Rejection Ratio V(Ripple) = 0.5VPP, IOUT = 10mA, frequency = 100Hz, COUT = 2.2µF — 70 — dB UVLO VIN Undervoltage Detection Ramp VIN up until the Output Turns on 2.1 2.4 2.7 V Hysteresis — 0.2 — V IFB FB Leakage Current FB = 0V (Adjustable Version) -10 — 20 nA AP7583AQ tD Output-Voltage Turn-On Delay Time VEN High to VOUT Rising 10% — 0.8 — ms tSS Output-Voltage Ramp-Up Time VOUT Rising 10% to 90% — 200 — µs tPG PG React Time VOUT 90% to PG Active — 30 — µs tPGF PG Off Deglitch Time VFB Falling to PG Low — 3 — µs EN Goes Low to PG Low VPGR PG Rising Threshold VFB Rising 90 — 94 % VPGF PG Falling Threshold VFB Falling 88 — 92 % VPGS PG Sinking Voltage Sinking Current = 5mA — — 0.4 V Note: 5. Dropout voltage is the voltage difference between the input and the output at which the output voltage drops 2% below its nominal value.

Document number: DS43764 Rev. 1 - 2 6 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Typical Characteristics (CIN = COUT = 10μF) AP7583Q AP7583Q AP7583AQ AP7583AQ AP7583Q AP7583Q

Document number: DS43764 Rev. 1 - 2 7 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Typical Characteristics (CIN = COUT = 10μF) (continued) AP7583AQ AP7583AQ AP7583Q AP7583Q AP7583AQ AP7583AQ

Document number: DS43764 Rev. 1 - 2 8 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Typical Characteristics (CIN = COUT = 10μF) (continued)

Document number: DS43764 Rev. 1 - 2 9 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Typical Characteristics (CIN = COUT = 10μF) (continued)

Document number: DS43764 Rev. 1 - 2 10 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Typical Characteristics (CIN = COUT = 10μF) (continued) Enable Turn-on Response Enable Turn-off Response VOUT = 3.3V VOUT = 3.3V Enable Turn-on Response Enable Turn-off Response VOUT = 5V VOUT = 5V Line Transient Response Line Transient Response VOUT = 3.3V, IOUT = 30mA VOUT = 5V, IOUT = 30mA VIN(DC) = 14V(5V/div) VEN(DC) = 0 to 2V(2V/div) VOUT = 3.3V(1V/div) VPG = 3.3V(2V/div) Time (1ms/div) VIN(DC) = 14V(5V/div) VEN(DC) = 2 to 0V(2V/div) VOUT = 3.3V(1V/div) VPG = 3.3V(2V/div) Time (1ms/div) VIN(DC) = 14V(5V/div) VEN(DC) = 0 to 2V(2V/div) VOUT = 5V(2V/div) VPG = 5V(5V/div) VIN(DC) = 14V(5V/div) VEN(DC) = 2 to 0V(2V/div) VOUT = 5V(2V/div) VPG = 5V(5V/div) Time (1ms/div) Time (1ms/div) VIN(DC) = 5.3 to 6.3V(1V/div) tR = tF = 5µs VOUT(AC): (50mV/div) Time (80µs/div) VIN(DC) = 7 to 8V(1V/div) tR = tF = 5µs VOUT(AC): (50mV/div) Time (80µs/div)

Document number: DS43764 Rev. 1 - 2 11 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Typical Characteristics (CIN = COUT = 10μF) (continued) Load Transient Response Load Transient Response VIN = 14V, VOUT = 3.3V VIN = 14V, VOUT = 3.3V Load Transient Response Load Transient Response VIN = 14V, VOUT = 5V VIN = 14V, VOUT = 5V VOUT(AC): (50mV/div) IOUT(AC) = 1 to 150mA (50mA/div) tR = tF = 5µs Time (80µs/div) VOUT(AC): (50mV/div) IOUT(AC) = 150 to 300mA (50mA/div) tR = tF = 5µs Time (80µs/div) VOUT(AC): (50mV/div) IOUT(AC) = 1 to 150mA (50mA/div) tR = tF = 5µs Time (80µs/div) VOUT(AC): (50mV/div) IOUT(AC) = 150 to 300mA (50mA/div) tR = tF = 5µs Time (80µs/div)

Application Information

A 1 0μF ceramic capacitor is recommended between IN and GND pins to decouple input power -supply glitch and noise. The amount of the capacitance may be increased without limit. This input capacitor must be located as close as possible to the device to assure input stability and reduce noise. For PCB layout, a wide copper trace is required for both IN and GND pins. A lower ESR capacitor type allows the use of less capacitance, while higher ESR type requires more capacitance. Output Capacitor Ceramic type output capacitor is recommende d for this series; however, the other output capacitors with low ESR also can be used. One 10μF output capacitor is suggested, the AP7583Q/AQ series LDO would have stable output capacitance range from 4.7 μF to 100μF. The relations between IOUT (Output Current) and ESR of an output capacitor are shown below. The stable region for the safety operating temperature (-40° C to +125° C) is marked as the gray area in the graph. Measurement conditions: Frequency Band: 10Hz to 2MHz, Temperature: -40° C to +125° C. Adjustable Operation The AP7583Q/AQ provides output voltage from 1.2V to 5.0V through external resistor divider as shown below: 10µF IN GND EN OUT Enable ADJ 10µF VIN VOUT AP7583Q/AQ Adjustable Output 10μF 10μF

Document number: DS43764 Rev. 1 - 2 13 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Application Information (continued) The output voltage is calculated by:   REFOUT R R1VV Where VREF = 1.2V (the internal reference voltage). Rearranging the equation will give the following that is used for adjusting the output to a particular voltage:   1V VR2R1 REF OUT To maintain the stability of the internal reference voltage, R2 needs to be kept smaller than 80k. No Load Stability Other than external resistor divider, no minimum load is required to keep the device stable. The device will remain stable an d regulated in no load condition. ON/OFF Input Operation The AP7583Q/AQ is turned on by setting the EN pin high, and is turned off by pulling it low. If this feature is not used, the EN pin should be tied to IN pin to keep the regulator output on at all time. To ensure proper operation, the signal s ource used to drive the EN pin must be able to swing above and below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section under VIL and VIH. Current Limit Protection When output current at OUT pin is higher than cu rrent-limit threshold, the current-limit protection will be triggered and clamp the output current to prevent overcurrent and to protect the regulator from damage due to overheating. Power Good The power-good (PG) pin is an open-drain output with one internal resistor. When the VOUT ≥ VPGR, the PG output is high-impedance; if the VOUT drops to below VPGF, or the device is disabled, the PG pin is pulled to low by an internal MOSFET. Thermal Shutdown Protection Thermal protection disables the output when the junction temperature rises to approximately +175° C, allowing the device to cool down. When the junction temperature reduces to approximately +155°C, the output circuitry is enabled again. Depending on power dissipation, thermal resistance, and ambient temperature, the thermal protec tion circuit may cycle on and off. This cycling limits the heat dissipation of the regulator, protecting it from damage due to overheating. Power Dissipation The device power dissipation and proper sizing of the thermal plane that is connected to the ther mal pad is critical to avoid thermal shutdown and ensure reliable operation. Power dissipation of the device depends on input voltage and load conditions and can be calculated by: PD = (VIN - VOUT) × IOUT The maximum power dissipation, handled by the dev ice, depends on the maximum junction to ambient thermal resistance, maximum ambient temperature, and maximum device junction temperature, which can be calculated by the equation in the following: θJAR )AT-C150( )A(max@TPD

Ordering Information

13/7: Tape & Reel Output Voltage Blank: ADJ 33 : 3.3V 50 : 5.0V PackageCompliance Q: Automotive Compliant FDZW : W-DFN2020-6 (SWP) (Type A1) Part Number Package Code Package Packing Qty. Carrier AP7583Q-XXFDZW-7 FDZW W-DFN2020-6 (SWP) (Type A1) 3,000 7” Tape & Reel AP7583AQ - XX XXXX - XX Packing 13/7: Tape & Reel Output Voltage Blank: ADJ 33 : 3.3V 50 : 5.0V PackageCompliance Q: Automotive Compliant MP : MSOP-8EP FDZW : W-DFN2020-6 (SWP) (Type A1) D4 : TO252-4 (Type C) Part Number Package Code Package Packing Qty. Carrier AP7583AQ-XXMP-13 MP MSOP-8EP 2,500 13” Tape & Reel AP7583AQ-XXFDZW-7 FDZW W-DFN2020-6 (SWP) (Type A1) 3,000 7” Tape & Reel AP7583AQ-XXD4-13(*) D4 TO252-4 (Type C) 2,500 13” Tape & Reel *: Future Product X 7: 7” Tape & Reel 13: 13” Tape & Reel 7: 7” Tape & Reel

Document number: DS43764 Rev. 1 - 2 15 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Marking Information (AP7583Q) (1) W-DFN2020-6 (SWP) (Type A1) (Top View) XXXX Y : Year : 0~9 X : Internal Code XXXX : Identification Code W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week Y W X Part Number Package Identification Code AP7583Q-FDZW-7 W-DFN2020-6 (SWP) (Type A1) F7AQ AP7583Q-33FDZW-7 W-DFN2020-6 (SWP) (Type A1) F7DQ AP7583Q-50FDZW-7 W-DFN2020-6 (SWP) (Type A1) F7EQ

Document number: DS43764 Rev. 1 - 2 16 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Marking Information (AP7583AQ) (1) MSOP-8EP 7583A-XXQ (Top View) Y W X E Identification Code 7583AQ : ADJ 7583A-33Q : 3.3V 7583A-50Q : 5.0V Logo 8 7 6 5 1 2 3 4 Y : Year : 0~9 a~z : 27~52 week; z represents W : Week : A~Z : 1~26 week; 52 and 53 week MSOP-8EP X : Internal Code Part Number Package Identification Code AP7583AQ-MP-13 MSOP-8EP 7583AQ AP7583AQ-33MP-13 MSOP-8EP 7583A-33Q AP7583AQ-50MP-13 MSOP-8EP 7583A-50Q (2) W-DFN2020-6 (SWP) (Type A1) (Top View) XXXX Y : Year : 0~9 X : Internal Code XXXX : Identification Code W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week Y W X Part Number Package Identification Code AP7583AQ-FDZW-7 W-DFN2020-6 (SWP) (Type A1) F8AQ AP7583AQ-33FDZW -7 W-DFN2020-6 (SWP) (Type A1) F8DQ AP7583AQ-50FDZW -7 W-DFN2020-6 (SWP) (Type A1) F8EQ

Document number: DS43764 Rev. 1 - 2 17 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Marking Information (AP7583AQ) (continued) (3) TO252-4 (Type C) 7583A-XXQIdentification Code Logo (Top View) YY WW XX XX : Internal Code YY : Year : 01 to 09 52 and 53 week 7583A-33Q : 3.3V 7583A-50Q : 5.0V WW : Week : 01 to 52, 52 represents Part Number Package Identification Code AP7583AQ-33D4-13 TO252-4 (Type C) 7583A-33Q AP7583AQ-50D4-13 TO252-4 (Type C) 7583A-50Q

Document number: DS43764 Rev. 1 - 2 18 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Package Outline Dimensions Please see http://www.diodes.com/package-outlines.html for the latest version. (1) MSOP-8EP (2) W-DFN2020-6 (SWP) (Type A1) D E DETAIL A 0.30±0.10

0.05 Ref

0.203 Ref

0.10 Ref

k L e b AA3 TERMINAL CROSS SECTION 0.20x45° DETAIL A W-DFN2020-6 (SWP) (Type A1) Dim Min Max Typ A 0.70 0.80 0.75 A1 0.00 0.05 0.02 A3 0.203 REF b 0.25 0.35 0.30 D 2.00 BSC D2 1.35 1.45 1.40 E 2.00 BSC E2 0.55 0.65 0.60 e 0.65 BSC k 0.20 –– –– L 0.20 0.40 0.30 All Dimensions in mm MSOP-8EP Dim Min Max Typ A - 1.10 - A1 0.05 0.15 0.10 A2 0.75 0.95 0.86 A3 0.29 0.49 0.39 b 0.22 0.38 0.30 c 0.08 0.23 0.15 D 2.90 3.10 3.00 D1 1.60 2.00 1.80 E 4.70 5.10 4.90 E1 2.90 3.10 3.00 E2 1.30 1.70 1.50 E3 2.85 3.05 2.95 e - - 0.65 L 0.40 0.80 0.60 a 0° 8° 4° x - - 0.750 y - - 0.750 All Dimensions in mm D A E e y x Seating Plane Gauge Plane 0.25 L4X10° 4X10° D 8Xb See Detail C Detail C c a

Document number: DS43764 Rev. 1 - 2 19 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Package Outline Dimensions (continued) Please see http://www.diodes.com/package-outlines.html for the latest version. (3) TO252-4 (Type C) TO252-4 (Type C) Dim Min Max Typ A 2.20 2.35 -- A1 0.00 0.15 -- A2 0.80 1.00 -- b 0.50 0.70 0.60 b2 5.30 5.70 -- c 0.46 0.58 -- c2 0.46 0.58 -- D 6.02 6.22 -- D2 4.24REF e 1.14BSC E 6.45 6.65 -- E2 5.00REF H 9.48 10.48 9.98 L 0.60 -- -- L1 2.76REF L2 0.65 0.95 0.80 L3 0.90 1.10 1.00 All Dimensions in mm Suggested Pad Layout Please see http://www.diodes.com/package-outlines.html for the latest version. (1) MSOP-8EP Dimensions Value (in mm) C 0.650 G 0.450 X 0.450 X1 2.000 Y 1.350 Y1 1.700 Y2 5.300 X C Y Y2 Y1 G DETAIL A E D H b e 4xe 0.150 max A 5° ±1° ( 4x) 7° ±1° DETAIL Aper side ( 0.050)( Ø1.0) SEATING PLANE A1L 0.100 GAUGE PLANE c

Document number: DS43764 Rev. 1 - 2 20 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ Suggested Pad Layout (continued) Please see http://www.diodes.com/package-outlines.html for the latest version. (2) W-DFN2020-6 (SWP) (Type A1) C1Y1 Y X C (3) TO252-4 (Type C) Mechanical Data  Moisture Sensitivity:  MSOP-8EP: Level 1 Per J-STD-020  W-DFN2020-6 (SWP) (Type A1): Level 1 Per J-STD-020  TO252-4 (Type C): Level 3 Per J-STD-020  Terminals: Finish - Matte Tin Plated Leads, Solderable per MIL-STD-202, Method 208  Weight:  MSOP-8EP: 0.024 grams (Approximate)  W-DFN2020-6 (SWP) (Type A1): 0.01 grams (Approximate)  TO252-4 (Type C): 0.343 grams (Approximate) Dimensions Value (in mm) C 0.650 C1 2.100 X 0.350 X1 1.400 Y 0.800 Y1 0.600 Dimensions Value (in mm) C 1.140 X 0.800 X1 5.360 X2 5.800 Y 2.200 Y1 6.400 Y2 1.980 Y3 10.600 Y C X

Document number: DS43764 Rev. 1 - 2 21 of 21 www.diodes.com December 2022 © 2022 Copyright Diodes Incorporated. All Rights Reserved. Advanced Information AP7583Q/AQ IMPORTANT NOTICE 1. DIODES INCORPORATED (Diodes) AND ITS SUBSIDIARIES MAKE NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO ANY INFORMATION CONTAINED IN THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON -INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). 2. The Information contained herein is fo r informational purpose only and is provided only to illustrate the operation of Diodes ’ products described herein and application examples. Diodes does not assume any liability arising out of the application or use of this document or any product described herein. This document is intended for skilled and technically trained engineering customers and users who design with Diode s’ products. Diodes’ products may be used to facilitate safety-related applications; however, in all instances customers and users are responsible for (a) selecting the appropriate Diodes products for their applications, (b) evaluating the suitability of Diodes ’ products for their intended applications, (c) ensuring their applications, which incorporate Diodes’ products, comply the applicable legal and regulatory requirements as well as safety and functional-safety related standards, and (d) ensuring they design with appropriate safeguards (including testing, validation, quality co ntrol techniques, redundancy, malfunction prevention, a nd appropriate treatment for aging degradation) to minimize the risks associated with their applications. 3. Diodes assumes no liability for any application -related information, support, assistance or feedback that may be provided by Diodes from time t o time. Any customer or user of this document or products described herein will assume all risks and liabilities associated w ith such use, and will hold Diodes and all companies whose products are represented herein or on Diodes’ websites, harmless against all damages and liabilities. 4. Products described herein may be covered by one or more United States, international or foreign patents and pending patent applications. Product names and markings noted herein may also be covered by one or more United S tates, international or foreign trademarks and trademark applications. Diodes does not convey any license under any of its intellectual property rights or the rights of any third parties (including third parties whose products and services may be described in this document or on Diodes’ website) under this document. 5. Diodes’ products are provided subject to Diodes’ Standard Terms and Conditions of Sale (https://www.diodes.com/about/company/terms-and-conditions/terms-and-conditions-of-sales/) or other applicable terms. This document does not alter or expand the applicable warranties provided by Diodes. Diodes does not warrant or accept any liability w hatsoever in respect of any products purchased through unauthorized sales channel. 6. Diodes’ products and technology may not be used for or incorporated into any products or systems whose manufacture, use or sale is prohibited under any applicable laws and regulations. Should customers or users use Diodes ’ products in contravention of any applicable laws or regulations, or for any unintended or unauthorized application, customers and users will (a) be solely responsible for any da mages, losses or penalties arising in connection therewith or as a result thereof, and (b) indemnify and hold Diodes and its representatives and age nts harmless against any and all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim relating to any noncompliance with the applicable laws and regulations, as well as any unintended or unauthorized application. 7. While efforts have been made to ensure the information contained in this document is accurate, complete and current, it may c ontain technical inaccuracies, omissions and typographical errors. Diodes does not warrant that information contained in this docume nt is error-free and Diodes is under no obligation to update or otherwise correct this information. Notwithstanding the foregoi ng, Diodes reserves the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any produ ct described herein. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes. 8. Any unauthorized copying, modification, distribution, transmission, display or other use of this document (or any portion her eof) is prohibited. Diodes assumes no responsibility for any losses incurred by the customers or users or any third parties arising f rom any such unauthorized use. 9. This Notice may be periodically updated with the most recent version available at https://www.diodes.com/about/company/terms-and- conditions/important-notice The Diodes logo is a registered trademark of Diodes Incorporated in the United States and other countries. DIODES is a trademark of Diodes Incorporated in the United States and other countries. All other trademarks are the property of their respective owners. © 2022 Diodes Incorporated. All Rights Reserved. www.diodes.com

Product Information

AP7583Q specifications and overview.

Summary

WIDE INPUT VOLTAGE RANGE, 300mA ULDO REGULATOR WITH PG December 2022 Rev. 1 - 2

Description

WIDE INPUT VOLTAGE RANGE, 300mA ULDO REGULATOR WITH PG December 2022 Rev. 1 - 2

Source title AP7583Q Datasheet(PDF) - Diodes Incorporated

Related Parts

More parts from the same family.

Browse manufacturer