AP3583 DIODES | Alldatasheet
Document overview
- Manufacturer or author: Diodes Incorporated
- PDF pages: 12
Technical content
Features
Supply Voltage: 5V/12V VIN Input Range: 3.0V to 13.2V 0.6V to 80% of VIN Output Range Internal Reference: 0.6V Support Tracking Mode and Stand-Alone Mode Simple Single-Loop Control Voltage-Mode PWM Control Duty Cycle: 0% to 80% Fast Transient Response Fixed Oscillator Frequency: 200/300kHz Lossless, Programmable Over Current Protection (Uses Lower MOSFET RDS(ON) ) Start-Up into Pre-biased Output Built-In Thermal Shutdown Built-In Soft-Start Over Current/Voltage Protection Under Voltage Protection Integrated Boot Diode Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2) Halogen and Antimony Free. “Green” Device (Note 3) Pin Assignments (Top View) BOOT UGATE OPS LGATE PHASE REFIN FB VCC GND PSOP-8
Applications
Power Supplies for Microprocessors/Peripherals PCs, Embedded Controllers, Memory Supplies DSP and Core Communications Processor Supplies Subsystem Power Supplies PCI, AGP, Graphics Cards and Digital TV SSTL-2 and DDR/2/3 SDRAM Bus Termination Supply Cable Modems, Set Top Boxes, and DSL Modems Industrial Power Supplies and General Purpose Supplies 5V/12V Input DC-DC Regulators Low-Voltage Distributed Power Supplies Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant. 2. See https://www.diodes.com/quality/lead-free/ for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds.
Document number: DS41575 Rev. 3- 2 2 of 12 www.diodes.com November 2018 © Diodes Incorporated AP3583/A Typical Applications Circuit VCC BOOT UGATE LGATE PHASE OPS REFIN FB AP3583/A Enable Disable 10k 10k GND VIN=12V VOUT=1.2V 1.0μH 1000μF/6.3V 1000μF/6.3V C3 1mF 0.1mF 10μF/25V 220μF/25V Reference Input R4 2W Pin Descriptions Pin Number Pin Name Function 1 BOOT Bootstrap pin. Connect a bootstrap capacitor (Typically from 0.1 to 0.47 μF) from this pin to PHASE pin to create a BOOT voltage suitable to drive a standard N-Channel MOSFET.
2 UGATE
Upper-gate drive pin. Connect this pin to the upper MOSFET gate providing the gate drive. This pin is monitored by the adaptive shoot -through protection circuitry to determine when the upper MOSFET has been turned off. 3 OPS Over-current setting pin. Connecting a resistor (R OCSET) between OPS and GND to set the over-current trigger point.
4 LGATE
Lower-gate drive pin. Connect LGATE to the lower MOSFET gate providing the gate drive for the lower MOSFET. This pin is monitored by the adaptive shoot-through protection circuitry to determine when the lower MOSFET has been turned off. 5 VCC Bias supply pin. Provides a 5V or 12V bias supply for the chip from this pin. The pin should be bypassed with a capacitor to GND. 6 FB Feedback pin. This pin is the inverting input of the internal error amplifier. A resistor divider from output to GND is used to set the output voltage.
7 REFIN
External reference input pin. This pin receives a voltage with range from 0.4V to 3.0V as the reference voltage at the non-inverting input of the error amplifier. Pull this pin lower than 0.3V to disable the controller, and the V UGATE and VLGATE will go low. Let this pin open for internal 0.6V reference use.
8 PHASE
PHASE pin. This pin connects to the source of the upper MOSFET and the drain of the lower MOSFET. This pin is also monitored by the adaptive shoot -through protection circuitry to determine when the upper MOSFET is turned off. 9 GND Exposed pad as ground pin. Represents the signal and power ground for the IC. Tie this pin to ground island/plane through the lowest impedance connection available.
Document number: DS41575 Rev. 3- 2 3 of 12 www.diodes.com November 2018 © Diodes Incorporated AP3583/A Functional Block Diagram OTP SOFT-START POWER-ON RESET (POR) INTERNAL REGULATOR 4V INT 0.6V OSCILLATOR PWM GATE CONTROL LOGIC ERROR AMPLIFIER PWM COMPARATOR VCC 0.3V ENABLE 137.5%VREF OVP REFIN GND OPS LGATE PHASE UGATE BOOT VCC REFERENCE SELECTION OCP COMPARATOR 40mA FB
Document number: DS41575 Rev. 3- 2 4 of 12 www.diodes.com November 2018 © Diodes Incorporated AP3583/A Absolute Maximum Ratings (Note 4) Symbol Parameter Value Unit VCC Supply Voltage -0.3 to 15 V VBOOT BOOT Voltage -0.3 to VPHASE +15 V VUGATE Voltage from UGATE to PHASE -0.3 to 15 V VPHASE, VLGATE Voltage from PHASE, LGATE Pin to GND -1 to 15 V _ Voltage on Other Separate Pin -0.3 to 6 V θJA Thermal Resistance 50 ºC/W TJ Operating Junction Temperature -40 to +125 ºC TSTG Storage Temperature -65 to +150 ºC TLEAD Lead Temperature (Soldering, 10 sec) +260 ºC _ ESD (Human Body Model) (Note 5) 2000 V _ ESD (Machine Model) (Note 5) 200 V Notes 4: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stres s ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Condi tions” is not implied. Exposure to “Absolute Maximum Ratings” for extended periods may affect device reliability. 5: Devices are ESD sensitive. Handling precaution recommended. Recommended Operating Conditions Symbol Parameter Min Max Unit VCC Supply Input Voltage 4.5 13.2 V TJ Operating Junction Temperature -40 +125 C TA Operating Ambient Temperature -40 +85 C
Document number: DS41575 Rev. 3- 2 5 of 12 www.diodes.com November 2018 © Diodes Incorporated AP3583/A Electrical Characteristics (VCC=12V, TA=+25℃, unless otherwise specified.) Symbol Parameter Conditions Min Typ Max Unit SUPPLY INPUT VCC Supply Voltage _ 4.5 _ 13.2 V ICC Supply Current UGATE1and1LGATEPin1Open; VCC=12V,1Switching _ 3 _ mA ICC_Q Quiescent Supply Current VFB=VREF+0.1V, No Switching _ 2 _ mA VIN Power Input Voltage _ 3.0 _ 13.2 V POWER ON RESET VPOR VCC Rising Threshold VCC Rising 4.0 4.2 4.4 V VPOR_HYS VCC Threshold Hysteresis _ _ 300 _ mV OSCILLATOR fOSC Oscillator Frequency AP3583 180 200 220 kHz AP3583A 270 300 330 ΔVOSC Ramp Amplitude VCC=12V _ 1.0 _ V PWM CONTROLLER GATE DRIVERS IUG_SRC Upper Gate Source Current VBOOT-VPHASE=12V, VBOOT- VUGATE=6V _ -1 _ A IUG_SNK Upper Gate Sink Current VBOOT-VPHASE=12V, VBOOT- VUGATE=6V _ 1.5 _ A RUGATE Upper Gate Sink Resistance 50mA Sink Current VBOOT-VPHASE=12V _ 1.6 3.2 Ω ILG_SRC Lower Gate Source Current VCC-VLGATE=6V _ -1 _ A ILG_SNK Lower Gate Sink Current VLGATE=6V _ 1.5 _ A RLGATE Lower Gate Sink Resistance VCC=12V, 50mA Source Current _ 1 2 Ω _ PHASE Falling to LGATE Rising Delay VPHASE<1.2V to VLGATE>1.2V _ 50 _ ns _ LGATE Falling to UGATE Rising Delay VLGATE<1.2V to (VUGATE- VPHASE)>1.2V _ 50 _ ns _ Minimum Duty Cycle _ _ 0 _ % _ Maximum Duty Cycle _ 75 80 85 % REFERENCE VOLTAGE VFB Feedback Voltage Stand-alone Mode 0.591 0.6 0.609 V
Document number: DS41575 Rev. 3- 2 6 of 12 www.diodes.com November 2018 © Diodes Incorporated AP3583/A Electrical Characteristics (Cont. VCC=12V, TA=+25℃, unless otherwise specified.) Symbol Parameter Conditions Min Typ Max Unit Output Voltage Accuracy │VFB-VREFIN│,1VREFIN=0.4V to 1.0V, Tracking Mode _ _ 15 mV │VFB-VREFIN│/VREFIN, V REFIN=1.0V to 3.0V, Tracking Mode _ _ 1.5 % VREFIN REFIN Enable Threshold _ _ 0.3 0.35 V PROTECTION VFB_UVP Under Voltage Protection _ 0.3 0.4 0.5 V IOPS Over Current Source _ 30 40 50 μA tSS Soft-start Interval AP3583,1Stand-alone Mode _ 2.6 _ ms _ AP3583A,1Stand-alone Mode _ 2.0 _ TOTSD Thermal Shutdown _ _ +160 _ ºC THYS Thermal Shutdown Hysteresis _ _ +20 _ ºC
Document number: DS41575 Rev. 3- 2 7 of 12 www.diodes.com November 2018 © Diodes Incorporated AP3583/A Performance Characteristics Line Regulation Load Regulation Switching Frequency vs. Temperature Switching Frequency vs. Input Voltage Feedback Voltage vs. Temperature Feedback Voltage vs. Input Voltage 4 5 6 7 8 9 10 11 12 13 14 -0.3 -0.2 -0.1 0.0 0.1 0.2 0.3 0.4 VOUT=1.2V, IOUT=10A Output Voltage Variation (%) Input Voltage (V) 0 2 4 6 8 10 12 14 16 18 20 22 -4.0 -3.5 -3.0 -2.5 -2.0 -1.5 -1.0 -0.5 0.0 0.5 1.0 VIN=12V, VOUT=1.2V Output Voltage Variation (%) Output Current (A) -50 -25 0 25 50 75 100 125 150 240 250 260 270 280 290 300 310 320 330 For AP3583A Switching Frequency (kHz) Temperature ( o 4 5 6 7 8 9 10 11 12 13 14 240 250 260 270 280 290 300 310 320 330 340 350 360 For AP3583A Switching Frequency (kHz) Input Voltage (V) -50 -25 0 25 50 75 100 125 150 0.500 0.525 0.550 0.575 0.600 0.625 0.650 0.675 0.700 Feedback Voltage (V) Temperature ( o 4 5 6 7 8 9 10 11 12 13 14 0.595 0.596 0.597 0.598 0.599 0.600 0.601 0.602 0.603 0.604 0.605 Feedback Voltage (V) Input Voltage (V)
Document number: DS41575 Rev. 3- 2 8 of 12 www.diodes.com November 2018 © Diodes Incorporated AP3583/A Performance Characteristics (Cont.) Power-on Waveform Power-off Waveform (VIN=12V, VOUT=1.2V, IOUT=0A) (VIN=12V, VOUT=1.2V, IOUT=0A) Enable Waveform Disable Waveform (VIN=12V, VOUT=1.2V, IOUT=0A) (VIN=12V, VOUT=1.2V, IOUT=20A) REFIN Operation Power Input Detection (VIN=12V, VOUT=1.2V, IOUT=5A) (VIN=12V, VOUT=1.2V, IOUT=0A) VIN 10V/div VOUT 0.5V/div VLGATE 5V/div IL 10A/div Time 1ms/div VIN 10V/div VOUT 0.5V/div VLGATE 5V/div IL 5A/div Time 200ms/div VREFIN 5V/div VOUT 0.5V/div VPHASE 10V/div IL 10A/div Time 1ms/div VREFIN 5V/div VOUT 0.5V/div VPHASE 10V/div IL 10A/div Time 40ms/div VOUT 2V/div VREFIN 2V/div VLGATE 10V/div Time 10ms/div VIN 5V/div VOUT 0.5V/div VLGATE 10V/div IL 10A/div Time 1ms/div
Document number: DS41575 Rev. 3- 2 9 of 12 www.diodes.com November 2018 © Diodes Incorporated AP3583/A Performance Characteristics (Cont.) UGATE Turn-off Waveforms UGATE Turn-on Waveforms (VIN=12V, VOUT=1.2V, IOUT=20A) (VIN=12V, VOUT=1.2V, IOUT=20A) Load Transient Response Load Transient Response (VIN=12V, VOUT=1.2V, IOUT=0 to 10A; 4A/ms) (VIN=12V, VOUT=1.2V, IOUT=0 to 20A; 4A/ms) Over Current Protection Over Voltage Protection (VIN=12V, VOUT=1.2V to 0V, IOUT=0A) (VIN=12V, VOUT=1.2V, IOUT=0A) VUGATE-PHASE 2V/div VPHASE 2V/div VUGATE 5V/div VLGATE 2V/div Time 40ns/div VUGATE-PHASE 2V/div VLGATE 2V/div VUGATE 5V/div VPHASE 2V/div VPHASE 5V/div VOUT(AC) 200mV/div IOUT 5A/div Time 10ms/div VPHASE 5V/div VOUT(AC) 200mV/div IOUT 10A/div Time 10ms/div VOUT 0.5V/div VPHASE 10V/div IL 10A/div Time 20ms/div VFB 1V/div VUGATE 20V/div VLGATE 10V/div IL 10A/div Time 80ms/div
Document number: DS41575 Rev. 3- 2 10 of 12 www.diodes.com November 2018 © Diodes Incorporated AP3583/A
Ordering Information
PackingPackageProduct Name TR : Tape & ReelBlank : AP3583 MP : PSOP-8 RoHS/Green A : AP3583A G1:RoHS Compliant and Green Package Temperature Range Part Number Marking ID Packing PSOP-8 -40 to +85° C AP3583MP-G1 3583MP-G1 Tube AP3583MPTR-G1 3583MP-G1 Tape & Reel AP3583AMP-G1 3583AMP-G1 Tube AP3583AMPTR-G1 3583AMP-G1 Tape & Reel Package Outline Dimensions (All dimensions in mm(inch).) (1) Package Type: PSOP-8 5.800(0.228) 6.200(0.244) 1.270(0.050) 0.400(0.016) 3.800(0.150) 4.000(0.157) 0.330(0.013) 0.150(0.006) 1.350(0.053) 1.750(0.069) TYP 0.250(0.010) 0.170(0.007) 1.350(0.053) 1.550(0.061) 2.313(0.091) 2.513(0.099) 3.202(0.126) 3.402(0.134) 5.100(0.201) Note: Eject hole, oriented hole and mold mark is optional.
Document number: DS41575 Rev. 3- 2 11 of 12 www.diodes.com November 2018 © Diodes Incorporated AP3583/A Suggested Pad Layout (1) Package Type: PSOP-8 G E X Y Y1 Z Dimensions Z (mm)/(inch) G (mm)/(inch) X (mm)/(inch) Y (mm)/(inch) Dimensions X1 (mm)/(inch) (mm)/(inch) E (mm)/(inch) ---
Document number: DS41575 Rev. 3- 2 12 of 12 www.diodes.com November 2018 © Diodes Incorporated AP3583/A IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make m odifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability a rising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporat ed website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmles s against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more U nited States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life sup port devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. suppo rt or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety -critical, life support devices or systems, notwithstanding any devices - or systems -related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2018, Diodes Incorporated www.diodes.com