DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Features
- Complies with UL ® Standard 864 (9th Edition).
- Expands the E3 and S3 Networks to two rings, contain- ing 122 nodes allowing a multi-ring network expansion.
- Provides expanded data exchanges between the E3 network and the FocalPoint Graphic Workstation.
- Includes high-speed configuration downloading through the ANX Ethernet port.
- Installed in the standard E3 Series cabinet enclosures.
- Bridges two of either the E3 Series or S3 Series Net- works to activate outputs on any node on bridged net- works.
- Offers shared ring capability. FocalPoint Features
- Displays device descriptions for points on events only.
- Shows a single icon per SLC device.
- Provides up to 512 Virtual Points for programmable control and status monitoring within FocalPoint for: - System control switch (Enable/Disable, Bypass). - Voice evacuation speaker circuit control switch. - Auxiliary control circuit switch.
- Provides Ethernet connectivity to allow a high speed supervised connection to the FocalPoint Gateway.
- Includes additional point information to the end user.
- Allows the user to send the following commands over the E3 Network. - Acknowledge - Reset - Silence - Enable/Disable
- Shows the current status on the E3 and S3 networks.
- Sends the time to the E3 and S3 networks. ANX
12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118
9021-60497 Rev. E page 2 of 2 www.gamewell-fci.com Ethernet The Addressable Node Expander uses TCP/IP and incor- porates heavy PPL/PSL/ re-use of the mainstream compo- nents. The three types of ANX sub-assemblies can provide Ethernet connectivity via an Ethernet port. This Ethernet port offers an enhanced network interface between the E3 Series and S3 Series fire alarm control panel and the FocalPoint Gra phic Workstation. This fea- ture improves the communication to monitor the alarm supervisory and trouble conditions of the FocalPoint Graphic Workstation. The E3 Series configuration data can be loaded into the netwo rk nodes via the ANX Ether- net port and CAMWorks™. A Download program utility is provided to extract data (excluding the CAMs and voice files on the INI-VG Series) into a job file that allows the ANX to extract all point infor- mation in existing panels. The following list the information that can be retrieved from the ANX.
- Custom labels programmed to identify each point.
- System information that de tails the configuration of analog addressable monitor and control points
- Information stored in the CAMWorks job file
- Compare feature to display configuration differences
- Converts low level CAMs into corresponding high level CAMs during the download of the CAMWorks configu- ration data for the following node types: - ILI-MB-E3 - ILI-S-E3 - ILI95-MB-E3 - ILI95-S-E3 - NGA - ANX - SLP-E3 E3 Series® and FocalPoint® are registered trademarks of Honeywell International Inc. CAMWorks™ is a trademark of Honeywell International Inc UL® is a registered trademark of Underwriters Laboratories Inc. Specifications Operating Voltage: 24 VDC (from the PM-9/PM-9G power supply) Operating/Supervisory Current: 0.066 amp Alarm Current: 0.066 amp Operating Temperature: 32° to 120° F (0° to 49° C) Relative Humidity: 0 to 93%, non-condensing at 90° F (32° C) Supervised Wiring Specifications: (ANX-MR-UTP & ANX-MR-FO only): Copper Wire: 16 to 18 AWG twisted-pair, unshielded. Up to 3,000 feet (914.4 m) between each node. Fiber-Optic Cable (ANX-MR-FO only): Up to 200 microns (optimized for 62.5/125 microns). Up to 8 dB loss between each node.
Ordering Information
ANX-SR Addressable Node Expander-Single Ring ANX-MR-UTP Addressable Node Expander-Multi-Ring Twisted-Pair ANX-MR-FO Addressable Node Expander-Multi-Ring Fiber Optic Figure 1: Addressable Node Expander Connection in a Multi-Ring Network Expansion Configuration