AND-1013ST PURDY | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Features

  • Super twisted, transflective, gray mode
  • RoHS Compliant
  • 20 characters x 16 line capability
  • 160 x 128 dot graphic display
  • Excellent readability and high-contrast ratio
  • Built-in LCD controller (T6963C)
  • Wide operating temperature range (0° to 50°C)
  • Available with EL backlighting (-EO option) or fiberoptic backlight Dot Matrix Dimensions Mechanical Characteristics Item Specification Unit Outline Dimensions 129.0 (W) x 104.5 (H) x 14.0 Max (D) mm Number of Dots 160 x 128 dots # of Characters 20 x 16 (320), 8 x 8 font Viewing Area 101.0 (W) x 82.0 (H) mm Bezel Opening 101.0 (W) x 82.0 (H) mm Dot Size 0.56 (W) x 0.56 (H) mm Dot Pitch 0.60 (W) x 0.60 (H) mm Weight (approx.) 150 gram 1. All dots on. DD .5V, V EE –8.5V, V EL =110, f EL = 500 Hz or at Typ. ) 2. mA rms Absolute Maximum Ratings Item Symbol Rating Unit Supply Voltage V DD 7.0 V V EE V EL 130 (EO) V rms Input Voltage V IN GND V IN V DD V Operating Temperature T op 0 to +50 °C Storage Temperature T stg -10 to +60 ˚C Electrical Characteristics (TA = 25°C) Item Symbol Min. Typ. Max. Unit Supply Voltage V DD 4.75 5.0 5.25 V V EE 11.7 12.4 12.8 High Level In Voltage DD = 5.0V) V IH V DD 2.2 – V DD V Low Level In Voltage DD = 5.0V) V IL – – 0.5 High Level Output Volt. DD = 5.0V) V OH V DD –0.3 –– V Low Level Output Volt. DD = 5.0V) V OL – – 0.3 V Power Consumption (1) I DD – – 10.0 mA I EE – – 2.0 I EL –1 5 (2) Product specifications contained herein may be changed without prior notice. It is therefore advisable to contact Purdy Electronics before proceeding with the design of equipment incorporating this product.

Intelligent Graphics Display AND1013ST-30/-EO Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 Tel: 408.523.8200 • Fax: 408.733.1287 • sales@purdyelectronics.com

  • www.purdyelectronics.com 12/22/06 Note:Refer to Applications Section for definitions of viewing angle, contrast ratio, response time (on and off) and luminance. Power Supply The LCD panel is driven by the voltage V DD EE , so an adjustable V EE is required for contrast control and temperature compensation. Example of Variable Negative Voltage Supply Timing Relationships and Diagram Timing Diagram Optical Characteristics (TA = 25˚C, φ = 0°, θ = 0) Item Symbol Min. Typ. Max. Unit Viewing Angle Right to Left – 80 – degree Up & Down – 55 – Contrast K 2.5 3.8 – – Turn On T on – 200 350 ms Turn Off T off – 250 350 ms Connector Pin Assignment Pin No. Signal Function

1 FGND Frame Ground (connected to metal bezel)

2 GND Ground (signal)

Power Supply for logic (5V) 4 V EE Power Supply for LCD Drive 5W R Data Write 6R D Data Read 7C E Chip Enable

8 C/D

WR = “L ”, C/D = “H”: Command Write WR = “L ”, C/D = “L ”: Data Write RD = “L ”, C/D = “H”: Status Read RD = “L ”, C/D = “L ”: Data Read

9 NC No connection

10 RESET Controller Reset

11 D0 Data Input/Output

12 D1 Data Input/Output

13 D2 Data Input/Output

14 D3 Data Input/Output

15 D4 Data Input/Output

16 D5 Data Input/Output

17 D6 Data Input/Output

18 D7 Data Input/Output

19 NC No connection

20 NC No connection

V DD EE 0°C 14.1 +25°C 13.0 +50°C 11.1 Signal Timing Relationships Item Symbol Min. Max. Unit C/D Set Up Time t CDS 100 – ns C/D Hold Time t CDH 10 – CE, RD WR Pulse Width t CE, t RD, t WR 80 – Data Set Up Time t DS 80 – Data Hold Time t DH 40 – Access Time t ACC – 150 Output Hold Time t OH 10 50 VEE VDD GND LCD ModuleR1 R1 = 10k, R2 = 10k, TR 2SA1102 or equivalent TR tCDS tCP,tRD,tWP tACC tCDH tDH tOH tDS C/D CE RD, WR D0-D7 (WRITE) D0-D7 (READ)

Intelligent Graphics Display AND1013ST-30/-EO Purdy Electronics Corporation • 720 Palomar Avenue • Sunnyvale, CA 94085 12/22/06 Tel: 408.523.8200 • Fax: 408.733.1287 • sales@purdyelectronics.com

  • www.purdyelectronics.com Block Diagram Dimensional Outline 8080 X-Driver Y-Driver Y-Driver LCD X-Driver T6963C Control Lines HSCP FR LP CDATA Because signal lines are directly connected to C-MOS and are not pull-up or pull-down internally, except RESET which is pull-up to V DD, you must guard all signals from external noise.12 R/W CE1 R/W CE I/O0-I/O7 A0-A11 RAM AD0-AD12 D0-D7 WR D0-D7 RD CE C/D RESET HALT