AN987 STMICROELECTRONICS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 10
Technical content
ST7 SERIAL TEST CONTROLLER PROGRAMMING by Microcontroller Division Applications INTRODUCTION This application note describes: – The advantages of Serial Test Controller Programming (STCP) vs. programming using an EPROM programming board (EPB) (see Section 2.1). – How to implement Serial Test Controller Programming targeting most of the ST7 general pur- pose microcontrollers (see Section 2.2). These devices include all parts supported by the ST7 starter kits and ST7 EPBs in the MDT1, MDT2 and MDT4 tool families (see the support- ed device list in APPENDIX 1). Note: In this application note, the term “programming tool” refers to either the EPBs or the starter kits.
1 PROGRAMMING TECHNIQUES
There are two possible ways of programming an ST7 device: ■ Using a programming tool. In this case, the device is first plugged on the programming board and then programmed. Then, the part is soldered or plugged into a socket on the user board. This can be done using any of the following ST7 programming tools: – ST7 Starter Kit – ST7 EPB (EPROM Programming Board) – ST7 Gang Programmer For further details about the above tools, please refer to the user manual supplied with these devices. ■ Using a Serial Test Controller Programming (STCP) tool. This technique allows a device to be directly programmed on the user board. This is a two-step procedure where first the board is first manufactured with a blank ST7, and afterwards the chip is programmed using a programming tool (Starter Kit or EPB). This application note describes the STCP method only.
2 SERIAL TEST CONTROLLER PROGRAMMING
2.1 ADVANTAGES
unsolder and change components in order to upgrade the application.
2.2 USER BOARD SPECIFICATION
Figure 1. shows the user board divided into two blocks: – Connector J1, which links the user board to the programming tool. – The ST72 MCU, which is the device to be programmed. tors (47 kΩ ) can be used instead of jumpers. This block consists of all the other components soldered on the user board.
Figure 1. User Board 1 for the pin connector assignment). – Pins M0, M1 and M2: These 3 pins are used to force the test modes.
ST7 SERIAL TEST CONTROLLER PROGRAMMING If these pins need to be tied to VDD or VSS , or if they are used by the user's application, they must be isolated from the user circuitry during programming. To do so, a jumper can be added for each of the eight pins (see Figure 2.). Note: Isolation resistors (47 kΩ ) can be used instead of jumpers only if these pins are used by the application as input (without Pull-up, without pull-down, or analog input configura- tion). ■ 3 system pins, VPP/TEST, RESET and OSCIN, which must be connected as follows: – The VPP/TEST pin must not be directly connected to GND/VSS on the application board in order to avoid any conflict with the programming voltage. This pin should be pulled down by a 10 kΩ resistor (see Figure 2.). – The RESET pin controls the entry into programming mode. This pin must be connected to a 10 kΩ pull-up resistor and a 1 nF capacitor connected to GND (see Figure 2.) to avoid any direct connections to VSS . This pin can be connected to a 47 kΩ isolation resistor if an external reset is provided by the application board. – The OSCIN pin synchronizes the programming operation using a clock generated by the programming tool. The OSCIN pin can be directly connected to the J1 connector. No iso- lation is needed as long as a quartz crystal or ceramic resonator is used in the application. If an external clock generator is used in the application, it must be disconnected during STC programming. Note: The OSCOUT pin does not need to be disconnected during the programming phase as long as a crystal, a ceramic resonator or an external clock source is used to drive the internal oscillator (user mode only). ■ The VDD and VSS power supply pins. The use of the VDD connection is optional, depending on whether the application board supply can be disconnected or not. If the application board supply is disconnected, the chip can be supplied through the programming tool (as long as the total current load does not exceed 100 mA and the capacitive load is less than 50 µF). In this case, only 1 jumper needs to be added in order to disconnect the V PP pin from the user circuitry during the programming sequence. No jumper is needed for VSS (see Figure 2.). If you want to use the application board power supply, its voltage must be 5 V, so that logic levels are compatible with those of the programming tool. Note: In any case, the ground from the application board and the ground from the programming tool must be connected together (see Figure 2.).
Figure 2. Block 1 The ST7 programming tool is connected to the user board via connector J1. Jumper use to disconnect the Application board supply if it is not 5 V. remove the connection between pin VDD and connector J1. (depending on the application configuration, refer to the note on page 3).
ST7 SERIAL TEST CONTROLLER PROGRAMMING
2.3 PROGRAMMING PROCEDURE
Depending on the device you need to program, use one of these ST7 programming tools: ■ ST7 MDT1-KIT or ST7 MDT1-EPB. They cover the following devices: – ST72101G1 or G2 – ST72212G2 – ST72213G1 – ST72251G1 or G2 ■ ST7 MDT2-KIT or ST7 MDT4-EPB. They cover the following devices: – ST72121J2 or J4 – ST72311J2 or J4 – ST72311N2 or N4 – ST72331J2 or J4 – ST72331N2 or N4 ■ ST7 MDT4-KIT or ST7 MDT4-EPB. They cover the following devices: – ST72272K2 or K4 – ST72372J4 – ST72371N4 – ST72671N4 or N6 After selecting the appropriate programming tool, proceed as follows: 1. On the application board, remove all jumpers. 2.Locate the 16 pin connector W1 (8x2 header HE10) on the programming tool which con- tains the 12 signals necessary for performing STCP (see Section 3 APPENDIX 1 for the pin identification).Then connect the W1 connector of the programming tool to the application board connector (J1 in Figure 1.). 3.Using the parallel interface cable, connect the PC parallel port to the parallel connector of the programming tool. 4.Power on the PC and the board. On the programming tool, LED 1 must light up. 5.Start the Windows EPROMer, target the programming tool, then the correct device. Open the file containing the code to program. And... program your device! 6.Close the operating software, power down the programming tool, disconnect the applica- tion board from the programming tool and replace any jumpers that were disconnected on the application board. Your application is now ready to run!
ST7 SERIAL TEST CONTROLLER PROGRAMMING
3 APPENDIX 1
The following table lists the devices supported by this application note and the specific starter kit required for each sales type. x = T, if the device is an OTP, E, if the device is an EPROM. Sales Type Starter Kit supporting the device ST72x101G1 ST7 MDT1 Starter kit or EPB ST72x101G2 ST72x212G2 ST72x213G1 ST72x251G1 ST72x251G2 ST72x121J2 ST7 MDT2 Starter kit or EPB ST72x121J4 ST72x311J2 ST72x311J4 ST72x311N2 ST72x311N4 ST72x331J2 ST72x331J4 ST72x331N2 ST72x331N4 ST72x272K2 ST7 MDT4 Starter kit or EPB ST72x272K4 ST72x371N4 ST72x372J4 ST72x671N4 ST72x671N6
ST7 SERIAL TEST CONTROLLER PROGRAMMING
4 APPENDIX 2
This appendix provides the required information for programming a device supported by the MDT1, MDT2 and MDT4 EPBs or starter kits. The five JTAG pins and three test mode pins (M0, M1 and M2) with their associated pin numbers are specified for each device.
4.1 ST7 MDT1 EPB OR STARTER KIT
x = T, if the device is an OTP, E, if the device is an EPROM, N.C., means not connected. ST7 Device Pin Numbers Sales type EPROM E 2 RAM Package JTDI PA3 JTCK PA2 JTRST PA1 JTMS PA0 JTDO PC3 PB2 PB1 PB0 Vpp Reset Oscin Vdd Vss ST72x101G1 4K - 256 SO28 SDIP32 ST72x101G2 8K - 256 SO28 SDIP32 ST72x212G2 8K - 256 SO28 SDIP32 ST72x213G1 4K - 256 SO28 SDIP32 ST72x251G1 4K - 256 SO28 SDIP32 ST72x251G2 8K - 256 SO28 SDIP32 Programming tool W1 connector 5 1 9 3 7 12 10 8 16 4 2 N.C 15
ST7 SERIAL TEST CONTROLLER PROGRAMMING
4.2 ST7 MDT2 EPB OR STARTER KIT
4.3 ST7 MDT4 EPB OR STARTER KIT
x = T, if the device is an OTP, E, if the device is an EPROM, N.C., means not connected. ST7 Device Pin Numbers Sales type EPROM E 2 RAM Package JTDI PA7 JTCK PA6 JTRST PA5 JTMS PA4 JTDO PA3 PB2 PB1 PB0 Vpp Reset Oscin ST72x121J2 8K - 384 TQFP44 SDIP42 ST72x121J4 16K - 512 TQFP44 SDIP42 ST72x311J2 8K - 384 TQFP44 SDIP42 ST72x311J4 16K - 512 TQFP44 SDIP42 ST72x311N2 8K - 384 TQFP64 SDIP56 ST72x311N4 16K - 512 TQFP64 SDIP56 ST72x331J2 8K 256 384 TQFP44 SDIP42 ST72x331J4 16K 256 512 TQFP44 SDIP42 ST72x331N2 8K 256 384 TQFP64 SDIP56 ST72x331N4 16K 256 512 TQFP64 SDIP56 Programming tool W1 connector 5 1 9 3 7 12 10 8 16 4 2 ST7 Device Pin Numbers Sales type EPROM E 2 RAM Package JTDI PA7 JTCK PA6 JTRST PA5 JTMS PA4 JTDO PC6 DA3 DA2 DA1 Vpp Reset Oscin Vdd Vss ST72x272K2 8K - 384 SO34 SDIP32 ST72x272K2 16K - 512 SO34 SDIP32 ST72x371N4 16K - 512 TQFP64 SDIP56 ST72x372J4 16K - 512 SDIP42 34 35 36 37 31 2 1 42 41 40 33 25 23 ST72x671N4 16K - 512 TQFP64 SDIP56 ST72x671N6 32K - 1K TQFP64 SDIP56 Programming tool W1 connector 5 1 9 3 7 12 10 8 16 4 2 N.C 15
ST7 SERIAL TEST CONTROLLER PROGRAMMING THE PRESENT NOTE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS WITH INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE CONTENT OF SUCH A NOTE AND/OR THE USE MADE BY CUSTOMERS OF THE INFORMATION CONTAINED HEREIN IN CONNEXION WITH THEIR PRODUCTS." Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without the express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2000 STMicroelectronics - All Rights Reserved. Purchase of I2C Components by STMicroelectronics conveys a license under the Philips I2C Patent. Rights to use these components in an I2C system is granted provided that the system conforms to the I2C Standard Specification as defined by Philips. STMicroelectronics Group of Companies Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com