AMS1083CT-15

AMS1083 ADMOS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 Advanced AMS1083 Monolithic 8A LOW DROPOUT VOLTAGE REGULATOR Systems FEATURES APPLICATIONS

• • Three Terminal Adjustable or Fixed •• High Efficiency Linear Regulators
• • Output Current of 8A •• Microprocessor Supply
• • Operates Down to 1V Dropout •• Battery Chargers
• • Line Regulation: 0.015% •• Constant Current Regulators
• • Load Regulation: 0.1% •• Notebook/Personal Computer Supplies
• • TO-220 and TO-263 packages available •• Portable Instrumentation GENERAL DESCRIPTION The The AMS1083 series of adjustable and fixed voltage regulators are designed to provide 8A output current and to operate down to 1V input-to-output differential. The dropout voltage of the device is guaranteed maximum 1.5V at maximum output current, decreasing at lower load currents. On-chip trimming adjusts the reference voltage to 1%. Current limit is also trimmed, minimizing the stress under overload conditions on both the regulator and power source circuitry. The AMS1083 devices are pin compatible with older three-terminal regulators and are offered in 3 lead TO-220 package and 3 lead TO-263 (Plastic DD). ORDERING INFORMATION: PACKAGE TYPE OPERATING JUNCTION

3 LEAD TO-220 3 LEAD TO-263 TEMPERATURE RANGE

AMS1083CT AMS1083CM 0 to 125 ° C AMS1083CT-1.5 AMS1083CM-1.5 0 to 125 ° C AMS1083CT-2.5 AMS1083CM-2.5 0 to 125 ° C AMS1083CT-2.85 AMS1083CM-2.85 0 to 125 ° C AMS1083CT-3.0 AMS1083CM-3.0 0 to 125 ° C AMS1083CT-3.3 AMS1083CM-3.3 0 to 125 ° C AMS1083CT-3.5 AMS1083CM-3.5 0 to 125 ° C AMS1083CT-5.0 AMS1083CM-5.0 0 to 125 ° C PIN CONNECTIONS FIXED VERSION ADJUSTABLE VERSION 1- Ground 2- V OUT 3- V IN 1 - Adjust 2- V OUT 3- V IN TAB IS OUTPUT FRONT VIEW 3TAB IS OUTPUT FRONT VIEW

Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMS1083 ABSOLUTE MAXIMUM RATINGS (Note 1) Power Dissipation Internally limited Soldering information Input Voltage 15V Lead Temperature (10 sec) 300 °C Operating Junction Temperature Range Thermal Resistance Control Section 0 °C to 125 °C TO-220 package ϕ JA = 50 °C/W Power Transistor 0 °C to 150 °C TO-263 package ϕ JA = 30 °C/W * Storage temperature - 65 °C to +150 °C * With package soldering to 0.5in 2 copper area over backside ground plane or internal power plane ϕ JA can vary from 20 °C/W to > 40 °C/W depending on mounting technique.

ELECTRICAL CHARACTERISTICS

Electrical Characteristics at I OUT = 0 mA, and T J = +25°C unless otherwise specified. Parameter Device Conditions Min Typ Max Units Reference Voltage (Note 2) AMS1083 I OUT = 10 mA 10mA ≤ I OUT ≤ 8A, 1.5V ≤ (V IN - V OUT ) ≤ 12V 1.238 1.225 1.250 1.250 1.262 1.270 V V Output Voltage (Note 2) AMS1083-1.5 0 ≤ I OUT ≤ 8A , 3V ≤ V IN ≤ 12V 1.485 1.470 1.500 1.500 1.515 1.530 V V AMS1083-2.5 0 ≤ I OUT ≤ 8A , 4V ≤ V IN ≤ 12V 2.475 2.450 2.500 2.500 2.525 2.550 V V AMS1083-2.85 0 ≤ I OUT ≤ 8A , 4.35V ≤ V IN ≤ 12V 2.820 2.790 2.850 2.850 2.880 2.910 V V AMS1083-3.0 0 ≤ I OUT ≤ 8A , 4.5V ≤ V IN ≤ 12V 2.970 2.940 3.000 3.000 3.030 3.360 V V AMS1083-3.3 0 ≤ I OUT ≤ 8A , 4.75V ≤ V IN ≤ 12V 3.267 3.235 3.300 3.300 3.333 3.365 V V AMS1083-3.5 0 ≤ I OUT ≤ 8A, 5V ≤ V IN ≤ 12V 3.465 3.430 3.500 3.500 3.535 3.570 V V AMS1083-5.0 0 ≤ I OUT ≤ 8A , 6.5V ≤ V IN ≤ 12V 4.950 4.900 5.000 5.000 5.050 5.100 V V Line Regulation AMS1083/-1.5/-2.5/-2.85/ I LOAD = 10 mA , 1.5V ≤ (V IN - V OUT ) ≤ 12V 0.3 0.6 mV mV Load Regulation (Notes 2, 3) AMS1083 (V IN - V OUT ) =3V, 10mA ≤ I OUT ≤ 8A 0.1 0.2 0.3 0.4 AMS1083-1.5 V IN = 5V, 0 ≤ I OUT ≤ 8A 3 mV mV AMS1083-2.5 V IN = 5V, 0 ≤ I OUT ≤ 8A 3 mV mV AMS1083-2.85 V IN = 5V, 0 ≤ I OUT ≤ 8A 3 mV mV AMS1083-3.0 V IN = 5V, 0 ≤ I OUT ≤ 8A 3 mV mV AMS1083-3.3 V IN = 5V, 0 ≤ I OUT ≤ 8A 3 mV mV AMS1083-3.5 V IN = 5.25V, 0 ≤ I OUT ≤ 8A 3 mV mV AMS1083-5.0 V IN = 8V, 0 ≤ I OUT ≤ 8A 5 mV mV Dropout Voltage (V IN - V OUT ) ΔV OUT , ΔV REF = 1%, I OUT = 8 A (Note 4) 1.3 1.5 V

Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMS1083 Electrical Characteristics at I OUT = 0 mA, and T J = +25°C unless otherwise specified. Parameter Device Conditions Min Typ Max Units Current Limit AMS1083/-1.5/-2.5/-2.85/ (V IN - V OUT ) = 5V 8.00 9.00 10.00 A Minimum Load Current AMS1083 (V IN - V OUT ) = 12V (Note 5) 5 10 mA Quiescent Current AMS1083/-1.5/-2.5/-2.85/ V IN ≤ 12V 5 10 mA Ripple Rejection AMS1083 f =120Hz , C OUT = 25 µF Tantalum, I OUT = 8A, (V IN -V OUT ) = 3V, C ADJ =25 µF 60 75 dB AMS1083-1.5 f =120Hz , C OUT = 25 µF Tantalum, I OUT = 8A, V IN = 4.5V 60 72 dB AMS1083-2.5 f =120Hz , C OUT = 25 µF Tantalum, I OUT = 8A, V IN = 5.5V 60 72 dB AMS1083-2.85 f =120Hz , C OUT = 25 µF Tantalum, I OUT = 8A, V IN = 6V 60 72 dB AMS1083-3.0 f =120Hz , C OUT = 25 µF Tantalum, I OUT = 8A V IN = 6V 60 72 dB AMS1083-3.3 f =120Hz , C OUT = 25 µF Tantalum, I OUT = 8A V IN = 6.3V 60 72 dB AMS1083-3.5 f =120Hz , C OUT = 25 µF Tantalum, I OUT = 8A V IN = 6.5V 60 72 dB AMS1083-5.0 f =120Hz , C OUT = 25 µF Tantalum, I OUT = 8A V IN = 8V 60 68 dB Thermal Regulation AMS1083 T A = 25°C, 30ms pulse 0.008 0.04 %W Adjust Pin Current AMS1083 10mA ≤ I OUT ≤ 8A , 1.5V ≤ (V IN - V OUT ) ≤ 12V 55 120 µA µA Adjust Pin Current Change AMS1083 10mA ≤ I OUT ≤ 8A , 1.5V ≤ (V IN - V OUT ) ≤ 12V 0.2 5 µA Temperature Stability 0.5 % Long Term Stability T A =125°C, 1000Hrs 0.3 1 % RMS Output Noise (% of V OUT ) T A = 25°C , 10Hz ≤ f ≤ 10kHz 0.003 % Thermal Resistance Junction-to-Case M Package: Control Circuitry/ Power Transistor T Package: Control Circuitry/ Power Transistor 1.5/4.0 1.5/4.0 °C/W °C/W Parameters identified with boldface type apply over the full operating temperature range. Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. For guaranteed specifications and test conditions, see the Electrical Characteristics . The guaranteed specifications apply only for the test conditions listed. Note 2: Line and Load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the input/output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. Note 3: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead ~1/8” from the package. Note 4: Dropout voltage is specified over the full output current range of the device. Note 5: Minimum load current is defined as the minimum output current required to maintain regulation. When (V IN - V OUT ) = 12V the device is guaranteed to regulate if the output current is greater than 10mA.

Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMS1083 APPLICATION HINTS The AMS1083 series of adjustable and fixed regulators are easy to use and have all the protection features expected in high performance voltage regulators: short circuit protection and thermal shut-down. Pin compatible with older three terminal adjustable regulators, these devices offer the advantage of a lower dropout voltage, more precise reference tolerance and improved reference stability with temperature. Stability The circuit design used in the AMS1083 series requires the use of an output capacitor as part of the device frequency compensation. The addition of 150 µF aluminum electrolytic or a 22 µF solid tantalum on the output will ensure stability for all operating conditions. When the adjustment terminal is bypassed with a capacitor to improve the ripple rejection, the requirement for an output capacitor increases. The value of 22 µF tantalum or 150 µF aluminum covers all cases of bypassing the adjustment terminal. Without bypassing the adjustment terminal smaller capacitors can be used with equally good results. To ensure good transient response with heavy load current changes capacitor values on the order of 100 µF are used in the output of many regulators. To further improve stability and transient response of these devices larger values of output capacitor can be used. Protection Diodes Unlike older regulators, the AMS1083 family does not need any protection diodes between the adjustment pin and the output and from the output to the input to prevent over-stressing the die. Internal resistors are limiting the internal current paths on the AMS1083 adjustment pin, therefore even with capacitors on the adjustment pin no protection diode is needed to ensure device safety under short-circuit conditions. Diodes between the input and output are not usually needed. Microsecond surge currents of 50A to 100A can be handled by the internal diode between the input and output pins of the device. In normal operations it is difficult to get those values of surge currents even with the use of large output capacitances. If high value output capacitors are used, such as 1000 µF to 5000 µF and the input pin is instantaneously shorted to ground, damage can occur. A diode from output to input is recommended, when a crowbar circuit at the input of the AMS1083 is used. Normal power supply cycling or even plugging and unplugging in the system will not generate current large enough to do any damage. The adjustment pin can be driven on a transient basis ±25V, with respect to the output without any device degradation. As with any IC regulator, none the protection circuitry will be functional and the internal transistors will break down if the maximum input to output voltage differential is exceeded. AMS1083 IN OUT ADJ + C OUT 150 µF V OUT R 1 R 2 C ADJ 10 µF V IN Overload Recovery When the power is first turned on, as the input voltage rises, the output follows the input, permitting the regulator to start up into heavy loads. During the start-up, as the input voltage is rising, the input-to-output voltage differential remains small, allowing the regulator to supply large output currents. A problem can occur with a heavy output load when the input voltage is high and the output voltage is low, when the removal of an output short will not permit the output voltage to recover. The load line for such a load may intersect two points on the output current curve. In this case, there are two stable output operating points for the regulator. With this double intersection, the power supply may need to be cycled down to zero and brought up again to make the output recover. Ripple Rejection The ripple rejection values are measured with the adjustment pin bypassed. The impedance of the adjust pin capacitor at the ripple frequency should be less than the value of R1 (normally 100 Ω to120 Ω ) for a proper bypassing and ripple rejection approaching the values shown. The size of the required adjust pin capacitor is a function of the input ripple frequency. If R1=100 Ω at 120Hz the adjust pin capacitor should be 25 µF. At 10kHz only 0.22 µF is needed. The ripple rejection will be a function of output voltage, in circuits without an adjust pin bypass capacitor. The output ripple will increase directly as a ratio of the output voltage to the reference voltage (V OUT / V REF ). Output Voltage The AMS1083 series develops a 1.25V reference voltage between the output and the adjust terminal. Placing a resistor between these two terminals causes a constant current to flow through R1 and down through R2 to set the overall output voltage.

Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMS1083 TYPICAL PERFORMANCE CHARACTERISTICS -2.0 -1.0 1.0 2.0 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (° C) 0 1 2 3 4 5 6 Dropout Voltage -0.20 -0.15 -0.10 -0.05 0.05 0.10 -50 -25 0 25 50 75 100 125 150 0 2 4 6 8 10 12 Short-Circuit Current Load Regulation -0.4 0.6 50 60 70 80 90 100 110 100 0 100 -100 150 100 Temperature Stability 7 8 9 10 Ripple Rejection vs. Current 100 1k 10k 100k Ripple Rejection 10050 8 ~~ ~~ -0.2 0.2 0.4 Load Transient Response 200 Line Transient Response 14 ~~ ~~-150 -50 100 Maximum Power Dissipation* 120 130 140 150 TIME ( µs) TIME ( µs) CASE TEMPERATURE (° C) *AS LIMITED BY MAXIMUM JUNCTION TEMPERATURE POWER (W) INPUT DEVIATION (V) OUTPUT VOLTAGE DEVIATION (mV) LOAD CURRENT (A) OUTPUT VOLTAGE DEVIATION (V) FREQUENCY (Hz) RIPPLE REJECTION (dB) RIPPLE REJECTION (dB) OUTPUT CURRENT (0 TO I FULL LOAD ) INPUT/OUTPUT DIFFERENTIAL (V) SHORT-CIRCUIT CURRENT (A) OUTPUT VOLTAGE CHANGE (%) TEMPERATURE (° C) OUTPUT VOLTAGE DEVIATION (%) OUTPUT CURRENT (A) MINIMUM INPUT/OUTPUT DIFFERENTIAL (V) f R = 120Hz V RIPPLE ≤ 3V P-P f R =20kHz V RIPPLE ≤ 0.5V P-P I OUT =I FULL LOAD (V IN -V OUT ) ≥V DROPOUT V RIPPLE ≤ 3V P-P V RIPPLE ≤ 0.5V P-P (V IN -V OUT ) ≥ 3V C ADJ = 0 V OUT = 10V I IN = 0.2A C IN = 1 µF TANTALUM C OUT = 10 µF TANTALUM V OUT = 10V V IN = 13V PRELOAD = 100mA C IN = 1 µF C OUT = 10 µF TANTALUM C ADJ = 0 ΔI = 8A T J =150° C T J =25° C

Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMS1083 TYPICAL PERFORMANCE CHARACTERISTICS (Continued) -50 -25 0 25 50 75 125 100 0 2 4 6 8 10 12 14 100 150 Minimum Operating Current (Adjustable only) Adjust Pin Current (Adjustable only) ADJUST PIN CURRENT ( µA) TEMPERATURE (° C)INPUT/OUTPUT DIFFERENTIAL (V) MINIMUM OPERATING CURRENT (mA) T J = 25° C T J = 150° C PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted.

3 LEAD TO-220 PLASTIC PACKAGE (T)

0.330-0.370 0.050 (8.382-9.398) 0.090-0.110 TYP 0.390-0.415 (9.906-10.541) 0.165-0.180 (4.191-4.572) 0.045-0.055 (1.143-1.397) 0.095-0.115 (2.413-2.921) 0.013-0.023 (0.330-0.584) T (TO-220) AMS DRW# 042193 0.147-0.155 (3.734-3.937) DIA 0.230-0.270 (5.842-6.858) 0.460-0.500 (11.684-12.700) 0.570-0.620 (14.478-15.748) 0.218-0.252 (5.537-6.401) 0.520-0.570 (13.208-14.478) 0.980-1.070 (24.892-27.178) 0.028-0.038 (0.711-0.965)

Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMS1083 PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted (Continued).

3 LEAD TO-263 PLASTIC DD (M)

0.330-0.370 0.032 0.060 (1.524) TYP (8.382-9.398) ( 5.05-5.54 ) 0.090-0.110 (2.286-2.794) 0.199-0.218 (0.81) TYP 0.390-0.415 (9.906-10.541) 0.165-0.180 (1.143-1.397) 0.095-0.115 (2.413-2.921) 0.90-0.110 (2.29-2.79) 0.013-0.023 (0.330-0.584) 0.108 (2.74) TYP ( 0.102 )+0.203 -0.102 0.004 +0.008 -0.004 M (DD3) AMS DRW# 042191R1