AMLD-6035Z

AMLD-Z AIMTEC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 13

Technical content

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 1 of 13 North America only FEATURES: Models Single output Model Input Voltage (V) Output Voltage (V) Output Current (mA) Efficiency (%) Ripple & Noise (mV p-p) AMLD-6015Z 7-60 2-57 150 97 150 AMLD-6025Z 7-60 2-57 250 97 200 AMLD-6030Z 7-60 2-57 300 97 250 AMLD-6035Z 7-60 2-57 350 97 300 AMLD-6050Z 7-60 2-57 500 97 400 AMLD-6070Z 7-60 2-57 700 97 500 AMLD-60100Z 7-60 2-48 1000 97 800 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Maximum Units Voltage range 7-60 VDC Filter Capacitor Absolute Maximum Rating 65 VDC Peak Input Voltage time 500 ms DC/DC ON (Leave open if not used) ON –Open or 0.3V<Vadj<1.25 DC/DC OFF OFF(shutdown) – Vadj<0.15 Maximum Remote pin drive current Vadj = 1.25V 1 mA Quiescent Current in Shutdown mode Vin = 60V, Vadj <0.15 0.1 mA On/Off Control (Digital Control) Max PWM Frequency 1KHz Output current adjustment PWM Frequency <300Hz 0.1 to 100 % Minimum Switch ON/OFF time 200 ns On/Off Control (Analog Dimming Control) (Leave open if not used) Input voltage range 0.3-1.25 VDC Output current adjustment* Vin-Vout<30 25-100 % Control Voltage Range limits ON – 0.2 – 0.3V (Vadj rise) OFF – 0.15-0.25V (Vadj fall) Maximum Analog pin drive current Vadj = 1.25V 1 mA NOTE: Vin –Vout must be less than 30V to maintain current adjustment range Output Specifications Parameters Conditions Typical Maximum Units Current accuracy ±7 % Output Voltage range V input = 60V 2-57 VDC Output current Vin – Vout > 3V Short Circuit protection Regulated at the rated current for each model Output no load Protection Continuously Max load capacitance 47 µF Temperature coefficient Ta = -40 to +85°C ±0.03 %/ oC Ripple & Noise 20MHz Bandwidth See model table

• Step Down DC/DC LED driver • Operating Temperature range -40ºC to +85ºC
• Constant current output • Open and Short LED Protection
• Ultra Wide (8:1) input voltage range • PWM/Digital and Analog Voltage dimming
• High efficiency up to 97% • Built with MLCC Capacitors only

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 2 of 13 North America only General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 20 - 500 KHz Operating temperature -40 to +85 oC Storage temperature -40 to +150 oC Derating See derating curve Maximum case temperature 110 oC Thermal Impedance Free air convection +30 oC/W Cooling Free air convection Humidity 95 % RH Case material Non-Conductive Black Plastic (UL94-V0 rated) Weight 12.5 g MTBF > 950 000hrs (MIL-HDBK-217 F at +25 oC) Maximum Soldering Temperature 1.5mm from case for 10sec. 260 oC NOTES: 1. Reversed polarity at the input power will damage the driver. The input ground must not be connected to the negative output. 2. Leave the pin VADJ opened if not used, grounding VADJ will shut the driver off, connecting VADJ to +Vin will damage the driver. 3. Maximum output open voltage is equal to input voltage. Safety Specifications Parameters Agency approvals CE Standards EN 55015 (CISPR22) EN 61547 IEC 61000-4-2 (Perf. Criteria A) IEC 61000-4-3 (Perf. Criteria A) IEC 61000-4-4 (Perf. Criteria A) IEC 61000-4-5 (Perf. Criteria A) IEC 61000-4-6 (Perf. Criteria A) IEC 61000-4-8 (Perf. Criteria A) Pin Out Specifications Pin Single 2 - V Input - DC Supply 3 - V Input - DC Supply

4 Vadj PWM/ON/OFF or not used

9 - V Output LED Cathode connection 11 - V Output LED Cathode connection 14 + V Output LED Anode connection 16 + V Output LED Anode connection 22 + V Input + DC Supply 23 + V Input + DC Supply

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 3 of 13 North America only Derating Dimensions 31.75 (1.25) 23 22 16 14 9 11 20.30 (0.80) 15.24 (0.60) 2.54 (0.1) 12.45 (0.49) 5.08 (0.2) 0.50 (0.02) 3.05 (0.12 Bottom View 25.40 (1.00 Application circuit examples: Mechanical Tolerances Case tolerance ± 0.25mm or ± 0.01 inches Pin tolerance ± 0.05 or ± 0.002 AMLD-Z +Vin -Vin VADJ 1st LED Last LED +Vout Analogue DIM PWM Dim/ON/OFF -Vout AMLD-Z +Vin -Vin VADJ 1st LED Last LED +Vout -Vout Analogue DIM PWM Dim/ON/OFF

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 4 of 13 North America only Application circuit examples (continued): Output Current Adjustment by External DC Control Voltage (VCTRL): VCTRL= VADJ (If VCTRL=0-1.25Vdc) (If VCTRL> 1.25Vdc) AMLD-Z +Vin -Vin VADJ 1st LED +Vout Analogue DIM PWM Dim/ON/OFF -Vout AC In AC In 5Vac to 42Vac Last LED 0.1uF optional 100uF to 330uF AMLD-Z -Vin VADJ 1st LED Last LED +Vout -Vout 0 -1.25V GND AMLD-Z -Vin VADJ 1st LED +Vout -Vout +5v 10K 30K Vctrl [ [ VADJ = R2 R1 + R2 X VCTRL AMLD-Z -Vin VADJ 1st LED +Vout -Vout 0 – 10VDC 10K 70K VCTRL

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 5 of 13 North America only Output Current Adjustment by External DC Control Voltage (VCTRL) (continued): Resistive Dimming Control A simplified dimming control can be achieved using a variable resistor connected between VADJ and GND. Capacitor CADJ is optional, it is installed to limit AC mains interference and high frequency noise. The recommended value of CADJ is 0.22µF. NOTE: Typical error is ±10% with resistive dimming control AMLD-Z -Vin VADJ 1st LED +Vout -Vout RADJ CADJ The output current is given by: If RADJ is between 0 and 2M ohm, the maximum adjustment range of Iout is 25% to 90% (for Vin – Vout < 20V) Ioutnom ≈ Iout x Radj (Radj + 50K) AMLD-Z -Vin VADJ 1st LED +Vout -Vout +Vin TL431 10K 10K 4.7K Last LED If Vin is between 7 VDC and 36 VDC it is recommended to use the circuit shown below AMLD-Z -Vin VADJ 1st LED +Vout -Vout TL431 10K 10K Last LED If Vin is between 36 VDC and 60 VDC it is recommended to use the circuit shown below +Vin 4.7KR1 KDZTR-27B [ [ VADJ = R3 R2 + R3 X 2.5 If VCTRL = Vin

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 6 of 13 North America only Output Current Adjustment by PWM Control: Driving VADJ Directly A Pulse Width Modulation (PWM) signal with a duty cycle DPWM can be applied to the ADJ pin as shown below. AMLD-Z -Vin VADJ 1st LED +Vout -Vout PWM 1.25V GND Last LED The output current is given by: Ioutnom x DPWMIout ≈ [if PWM frequency < 300Hz, for 0.1<DPWM<1] Driving VADJ Via Open Collector Transistor The VADJ can also be driven via an open collector transistor as shown below. The diode and resistor serve to suppress any possible high amplitude negative voltage spikes to the VADJ input resulting from the collector to emitter capacitance of the transistor. Any negative voltage spikes will cause errors in output current and/or unstable driver operation.

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 7 of 13 North America only Driving the VADJ from a Microcontroller The VADJ can be driven from an open drain output of a microcontroller as shown below. The diode and resistor serve to suppress any possible high amplitude negative voltage spikes to the VADJ input resulting from the drain to source capacitance of the FET. Any negative voltage spikes will cause errors in output current and/or unstable driver operation. Output Current Adjustment by PWM Control (Dimming): A PWM signal must have a frequency of greater than 100Hz to prevent any visible flicker. Output Current Adjustment by PWM Control (Flash):

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 8 of 13 North America only Recommended Class B EMI Filter: AMLD-Z +Vin -Vin VADJ 1st LED Last LED +Vout Analogue DIM PWM Dim/ON/OFF -Vout 4.7uF 47uH 4.7uF Typical Characteristics: AMLD-6030Z Efficiency vs Vin ( Forward Voltage = 3.5V per LED) 100 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Vin (V) Efficiency (%)

1 LED

2 LED

3 LED

4 LED 5 LED

6 LED 7 LED

7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Vin (V) Frequency (KHz) Operating Frequency vs Input Voltage (Forward Voltage = 3.5V per LED)

4 LED

5 LED

6 LED

7 LED

VADJ (V) ILED (mA)

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 9 of 13 North America only Typical Characteristics: AMLD-6035Z 7 8 9 1 01 11 21 31 41 51 61 71 81 92 02 12 22 32 42 52 62 72 82 93 0 Vin (V) Frequency (KHz) Operating Frequency vs Input Voltage (Forward Voltage = 3.5V per LED) VADJ (V) ILED (mA) Vin (V)

5 LED 6 LED

(Forward Voltage = 3.5V per LED) 70.00 75.00 80.00 85.00 90.00 95.00 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Efficiency (%)

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 10 of 13 North America only Typical Characteristics: AMLD-6050Z 70.00% 75.00% 80.00% 85.00% 90.00% 95.00% 100.00% 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Vin (V) Efficiency (%) Efficiency vs Vin (Forward Voltage = 3.5V per LED)

4 LED 5 LED 6 LED 7 LED

7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Vin (V) Frequency (KHz) Operating Frequency vs Input Voltage (Forward Voltage = 3.5V per LED)

1 LED 2 LED

VADJ (V) ILED (mA)

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 11 of 13 North America only Typical Characteristics: AMLD-6060Z 100 125 150 175 200 225 250 275 300 325 7 8 9 1 01 11 21 31 41 51 61 71 81 92 02 12 22 32 42 52 62 72 82 93 0 Vin (V) Frequency (KHz) Operating Frequency vs Input Voltage (Forward Voltage = 3.5V per LED) VADJ (V) ILED (mA) 70% 75% 80% 85% 90% 95% 100% 7 8 9 1 01 11 21 31 41 51 61 71 81 92 02 12 22 32 42 52 62 72 82 93 0 Vin (V) Efficiency (%) Efficiency vs Vin (Forward Voltage = 3.5V per LED)

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 12 of 13 North America only Typical Characteristics: AMLD-6070Z 100 125 150 175 200 225 250 275 300 325 350 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Vin (V) Frequency (KHz) Operating Frequency vs Input (Forward Voltage = 3.5V per LED)) VADJ (V) ILED (mA) 70% 75% 80% 85% 90% 95% 100% 7 8 9 1 01 11 21 31 41 51 61 71 81 92 02 12 22 32 42 52 62 72 82 93 0 Vin (V) Efficiency (%) Efficiency vs Vin (Forward Voltage = 3.5V per LED)

Up to 1000mA | LED Driver www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 13 of 13 North America only Typical Characteristics: AMLD-60100Z NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. 70% 75% 80% 85% 90% 95% 100% 7 8 9 1 01 11 21 31 41 51 61 71 81 92 02 12 22 32 42 52 62 72 82 93 0 Vin (V) Efficiency (% ) Efficiency vs Vin (Forward Voltage = 3.5V per LED)

5 LED 6 LED 7 LED

7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Vin (V) Frequency (KHz) Operating Frequency vs Input Voltage (Forward Voltage = 3.5V per LED)

7 LED 5 LED 3 LED

2 LED 4 LED 6 LED

VADJ (V) ILED (mA)