AMIS-42670_13 ONSEMI | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 10
Technical content
Features
- Fully Compatible with the ISO 11898−2 Standard
- Certified “Authentication on CAN Transceiver Conformance (d1.1)”
- Wide Range of Bus Communication Speed (0 Mbit/s up to 1 Mbit/s)
- Allows Low Transmit Data Rate in Networks Exceeding 1 km
- Ideally Suited for 12 V and 24 V Industrial and Automotive
Applications
- Low Electromagnetic Emission (EME) Common−Mode Choke is No Longer Required
- Differential Receiver with Wide Common−Mode Range (/C003635 V) for High EMS
- No Disturbance of the Bus Lines with an Unpowered Node
- Thermal Protection
- Bus Pins Protected Against Transients
- Silent Mode in which the Transmitter is Disabled
- Short Circuit Proof to Supply V oltage and Ground
- Logic Level Inputs Compatible with 3.3 V Devices
- These are Pb−Free Devices* *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com PIN ASSIGNMENT (Top View) TxD RxD S GND CANL AMIS− 42670 PC20041204.3 See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet.
ORDERING INFORMATION
Table 1. TECHNICAL CHARACTERISTICS
- The parameters V CM−peak and VCM−step guarantee low electromagnetic emission.
Figure 1. Block Diagram Table 2. PIN DESCRIPTION
1 TxD Transmit Data Input; Low Input → Dominant Driver; Internal Pullup Current
2 GND Ground
3 VCC Supply Voltage
4 RxD Receive Data Output; Dominant Transmitter → Low Output
5 VREF Reference Voltage Output
6 CANL Low−Level CAN Bus Line (Low in Dominant Mode)
7 CANH High−Level CAN Bus Line (High in Dominant Mode)
8 S Silent Mode Control Input; Internal Pulldown Current
AMIS−42670 http://onsemi.com Table 3. ABSOLUTE MAXIMUM RATINGS
- Applied transient waveforms in accordance with ISO 7637 part 3, test pulses 1, 2, 3a, and 3b (see Figure 3).
- Standardized human body model ESD pulses in accordance to MIL883 method 3015.7.
- Static latch −up immunity: static latch−up protection level when tested according to EIA/JESD78.
- Standardized charged device model ESD pulses when tested according to EOS/ESD DS5.3 −1993.
Table 4. THERMAL CHARACTERISTICS
APPLICATION INFORMATION
AMIS− 42670 CANH CANL GND RxD TxD VREF PC20070831.3 VCC S CAN controller VBAT 5V−reg IN OUT 47 nF 60 /C008760 /C0087 CAN BUS 47 nF 60 /C008760 /C0087 VCC GND Figure 2. Application Diagram
one of two operating modes can be selected through Pin S. Table 5. FUNCTIONAL TABLE OF AMIS−42670; x = don’t care controller which is out of control. dissipation increases during this fault condition.
AMIS−42670 http://onsemi.com
ELECTRICAL CHARACTERISTICS
All voltages are referenced to GND (Pin 2). Positive currents flow into the IC. Sinking current means the current is flowing into the pin; sourcing current means the current is flowing out of the pin. Table 6. DC CHARACTERISTICS VCC = 4.75 V to 5.25 V, TA = −40°C to +150°C; RLT = 60 /C0087 unless specified otherwise.
AMIS−42670 http://onsemi.com DEVICE ORDERING INFORMATION Part Number Temperature Range Package Type Shipping† AMIS42670ICAH2G −40°C − 125°C SOIC−8 (Pb−Free)
96 Tube / Tray
AMIS42670ICAH2RG −40°C − 125°C SOIC−8 (Pb−Free) 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
AMIS−42670 http://onsemi.com PACKAGE DIMENSIONS SOIC 8 CASE 751AZ−01 ISSUE O ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 AMIS−42670/D LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative