AMIS-30600 ONSEMI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 11

Technical content

Features

  • LIN−Bus Transceiver ♦ LIN compliant to specification rev. 1.3 and rev. 2.0 ♦ I2T high−voltage technology ♦ Bus voltage /C0036 40 V ♦ Transmission rate up to 20kbaud ♦ SOIC−150−8 package
  • Protection ♦ Thermal shutdown ♦ Indefinite short circuit protection to supply and ground
  • Load dump protection (45 V)
  • Power Saving ♦ Operating voltage = 4.75 to 5.25 V ♦ Power down supply current < 50 /C0109A
  • EMS Compatibility ♦ Integrated filter and hysteresis for receiver
  • EMI Compatibility ♦ Integrated slope control for transmitter ♦ Slope control dependant from Vbat to enable maximum capacitive load
  • These are Pb−Free Devices *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com PIN ASSIGNMENT (Top View) RxD TxD INH EN LIN AMIS− 30600 PC20041204.3 See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet.

ORDERING INFORMATION

Table 1. PIN LIST AND DESCRIPTIONS

1 RxD Receive data output; low in dominant state

2 EN Enable input; transceiver in normal operation mode when high

3 VCC 5V supply input

4 TxD Transmit data input; low in dominant state; internal 40 k/C0087 pullup

5 GND Ground

6 LIN LIN bus output/input; low in dominant state; internal 30 k/C0087 pullup

7 VBB Battery supply input

8 INH Inhibit output; to control a voltage regulator; becomes high when wake−up via LIN bus occurs

Table 2. ABSOLUTE MAXIMUM RATINGS

  1. Standardized Human Body Model system ESD pulses in accordance to IEC 1000.4.2.
  2. Applied transient waveforms in accordance with “ISO 7637 parts 1 & 3”, capacitive coupled test pulses 1 (−100 V), 2 (+100 V), 3a (−150 V),

and 3b (+150 V). See Figure 8.

  1. Applied transient waveforms in accordance with “ISO 7637 parts 1 & 3”, direct coupled test pulses 1 (−100 V), 2 (+75 V), 3a (−150 V), 3b

Table 3. OPERATING RANGE

AMIS−30600 http://onsemi.com

APPLICATION INFORMATION

PC20061221.1 VCC = on permanently VCC controlled by INH: INH = Float B VCC = off INH = H B VCC = on POWER UP EN = H EN = L INH = H Rx = H EN = L Wake−up over bus t > t wake VBB = on and VCC = on EN = H INH = Float Rx = H INH = H Rx = LIN data STANDBY MODE NORMAL MODE SLEEP MODE POWER UP EN = H EN = L INH = H B VCC = on Rx = H EN = L Wake−up over bus t > t wake INH = FloatB VCC = off Rx = Float INH = H Rx = LIN data STANDBY MODE NORMAL MODE SLEEP MODE VBB = on Figure 3. State Diagrams transients on the supply line. be set in normal operation mode by EN = H (see Figure 3).

Table 4. DC CHARACTERISTICS VCC = 4.75 V to 5.25 V; VBB = 7.3 V to 18 V,VEN < VENon, TA = −40°C to +125°C; RL = 500 /C0087 unless specified otherwise. All voltages with respect to ground, positive current flowing into pin, unless otherwise specified.

  1. Guaranteed by design. The total resistance of the pullup resistor and the serial diode is measured on ATE.

Table 5. AC ELECTRICAL CHARACTERISTICS ACCORDING TO LIN V13 VCC = 4.75 V to 5.25 V; VBB = 7.3 V to 18 V,VEN

  1. Guaranteed by design; not measured for all supply/load combinations on ATE.

AMIS−30600 http://onsemi.com DEVICE ORDERING INFORMATION Part Number Temperature Range Package Type Shipping† AMIS30600LINI1G −40°C − 125°C SOIC−8 (Pb−Free)

96 Tube / Tray

AMIS30600LINI1RG −40°C − 125°C SOIC−8 (Pb−Free) 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.

AMIS−30600 http://onsemi.com PACKAGE DIMENSIONS SOIC 14 CASE 751AP−01 ISSUE A DATE 29 AUG 2008

AMIS−30600 http://onsemi.com ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 AMIS−30600/D LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative