AM-184 MA-COM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Features
- 20 dB High Gain
- 60 mA Maximum Low Power
Description
M/A-COM’s AM-184 is a feedback amplifier with high intercept and compression points. This amplifier is packaged in a TO-8 package. Due to the internal power dissipation the thermal rise should be minimized. The ground plane on the PC board should be configured to remove heat from under the package. AM-184 is ideally suited for use where a high intercept, high reliability amplifier is required. TO-8-1 Parameter Absolute Maximum Max. Input Power +13 dBm Vbias +15.75 V Operating Temperature -55°C to +85°C Storage Temperature -65°C to +125°C Absolute Maximum Ratings 1 1. Operation of this device above any one of these parameters may cause permanent damage.
Ordering Information
- Mounting kit part number AU00071 required for PCB applications. Outline Drawing: SMA Connectorized * ∗ Dimensions are inches (millimeters) ±0.015 (0.38) unless otherwise specified.
Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Cascadable Thin Film Amplifier, 20 dB Gain, 10 - 2000 MHz Rev. V4 AM-184 / AMC-184 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Electrical Specifications: 2,3 TA = -55°C to +85°C Case Temperature Parameter Test Conditions Units Min. Typ. Max. Gain @+25oC dB 19.0 20.0 21.0 Frequency Response — dB — ±1.5 Gain Variation with Temperature — dB — — ±1.5 1 dB Compression Output Power dBm +10 — — Noise Figure — dB — — 6.0 Reverse Transmission — dB — -30 -27 VSWR — Ratio 2.0:1 Output IP2 Two-Tone inputs up to 0 dBm dBm +30 — — Output IP3 Two-Tone inputs up to 0 dBm dBm +20 — — Vbias — VDC +14.5 +15.0 +15.5 Ibias Vbias = +15.0 VDC mA — 52 60 Power Dissipation @ +15 V Bias mW — 780 — Frequency
1000 MHz
- All specifications apply when operated at +15 VDC, with 50 ohms source and load impedance. 3. Heat Sinking: Operation at case temperature above 95°C is not recommended. Heat sinking adequate to dissipate 1.0 W must be provided in use. Frequency (MHz) S11 MAG/ANG S21 MAG/ANG S12 MAG/ANG S22 MAG/ANG 0.10/80.7 S-Parameter Data
Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Cascadable Thin Film Amplifier, 20 dB Gain, 10 - 2000 MHz Rev. V4 AM-184 / AMC-184 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Typical Performance Curves