AM-180 MA-COM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Features

  • +14 dBm Typical 1 dB Compression
  • 5 dB Typical Noise Figure
  • 1.4:1 Typical VSWR

Description

M/A-COM’s AM-180 is a feedback amplifier with high intercept and compression points. This amplifier is packaged in a TO-8 package. Due to the internal power dissipation the thermal rise should be minimized. The ground plane on the PC board should be configured to remove heat from under the package. AM-180 is ideally suited for use where a high intercept, high reliability amplifier is required. TO-8-1 Parameter Absolute Maximum Max. Input Power +10 dBm Vbias +15.75 V Operating Temperature -55°C to +85°C Storage Temperature -65°C to +125°C Absolute Maximum Ratings 1 1. Operation of this device above any one of these parameters may cause permanent damage.

Ordering Information

Outline Drawing: SMA Connectorized * ∗ Dimensions are inches (millimeters) ±0.015 (0.38) unless otherwise specified.

Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Cascadable Thin Film Amplifier, 10 dB Gain, 10 - 2000 MHz Rev. V4 AM-180 / AMC-180 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Electrical Specifications: 2,3 TA = -55°C to +85°C Case Temperature Parameter Test Conditions Units Min. Typ. Max. Gain @+25oC dB 8.7 9.7 10.7 Frequency Response — dB — ±1.0 Gain Variation with Temperature — dB — — ±1.0 1 dB Compression Output Power dBm +13 — — Noise Figure — dB 7.0 Reverse Transmission — dB — -14 -12 VSWR — Ratio 2:1 Output IP2 Two-Tone inputs up to 0 dBm dBm +39 — — Output IP3 Two-Tone inputs up to 0 dBm dBm +25 — — Vbias — VDC +14.5 +15.0 +15.5 Ibias Vbias = +15.0 VDC mA — 45 50 Power Dissipation @ +15 V Bias mW — 680 — Frequency

1000 MHz

  1. All specifications apply when operated at +15 VDC, with 50 ohms source and load impedance. 3. Heat Sinking: Operation at case temperature above 95°C is not recommended. Heat sinking adequate to dissipate 800 mW must be provided in use. Frequency (MHz) S11 MAG/ANG S21 MAG/ANG S12 MAG/ANG S22 MAG/ANG 0.24/166.9 0.23/170.3 0.22/171.1 0.21/166.1 200 0.18/170.9 3.01/162.0 500 0.13/149.3 3.05/134.3 S-Parameter Data

Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Cascadable Thin Film Amplifier, 10 dB Gain, 10 - 2000 MHz Rev. V4 AM-180 / AMC-180 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Typical Performance Curves