AM-155 MA-COM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Features
- 2.5 dB Typical Midband Noise Figure
- +21 dBm Typical Midband Output Power
- +37 dBm Typical Midband Third Order Intercept
Description
M/A-COM’s AM-155 is a coupler feedback amplifier with high intercept and compression points. The use of coupler feedback minimizes noise figure and current in a high intercept amplifier. This amplifier is packaged in a TO-8 package. Due to the internal power dissipation the thermal rise minimized. The ground plane on the PC board should be configured to remove heat from under the package. AM-155 is ideally suited for use where a high intercept, high reliability amplifier is required. TO-8-1 Parameter Absolute Maximum Max. Input Power +10 dBm Vbias +15.75 V Operating Temperature -55°C to +85°C Storage Temperature -65°C to +125°C Absolute Maximum Ratings 1 1. Operation of this device above any one of these parameters may cause permanent damage.
Ordering Information
- Mounting kit part number AU00071 required for PCB applications. Outline Drawing: SMA Connectorized * ∗ Dimensions are inches (millimeters) ±0.015 (0.38) unless otherwise specified.
Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. High Dynamic Range Amplifier, 12.5 dB Gain, 300 - 1000 MHz Rev. V4 AM-155 / AMC-155 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Electrical Specifications: 2,3 TA = -55°C to +85°C Case Temperature Parameter Test Conditions Units Min. Typ. Max. Gain @+25oC dB 11.25 12.25 13.25 Frequency Response — dB — ±0.5 Gain Variation with Temperature — dB — — ±0.7 1 dB Compression Output Power dBm +18 — — Noise Figure — dB dB 4.0 5.5 Reverse Transmission — dB — -14 -10 VSWR Input Output Ratio Ratio 2.0:1 3.0:1 Output IP2 Two-Tone inputs up to +5 dBm dBm +40 — — Output IP3 Two-Tone inputs up to +5 dBm dBm +27 — — Vbias — VDC +14.5 +15.0 +15.5 Ibias Vbias = +15.0 VDC mA — 50 60 Power Dissipation @ +15 V Bias mW — 750 — Frequency
600 MHz
- All specifications apply when operated at +15 VDC, with 50 ohms source and load impedance. 3. Heat Sinking: Operation at case temperature above 95°C is not recommended. Heat sinking adequate to dissipate 0.8W must be provided in use. Frequency (MHz) S11 MAG/ANG S21 MAG/ANG S12 MAG/ANG S22 MAG/ANG 0.36/87.8 0.33/80.5 0.30/76.2 0.28/73.4 900 0.27/175.6 4.01/59.5 S-Parameter Data
Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. High Dynamic Range Amplifier, 12.5 dB Gain, 300 - 1000 MHz Rev. V4 AM-155 / AMC-155 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Typical Performance Curves