AM-AMC-151 MACOM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Features
n 5 dB Typical Midband Noise Figure n +38 dBm Typical Midband Third Order Intercept n +21 dBm Typical Midband 1 dB Compression
Description
M/A-COM’s AM-151 is a coupler feedback amplifier with high intercept and compression points. The use of coupler feedback minimizes noise figure and current in a high intercept amplifier. This amplifier is packaged in a TO -8 package. Due t o the internal power dissipation the thermal rise minimized. The ground plane on the PC board should be configured to remove he at from under the package. AM-151 is ideally suited for use where a high intercept, high reliability amplifier is required. Cascadable Thin Film Amplifier, 12 dB Gain, 5 - 500 MHz AM-/AMC-151 TO-8-1 C-32 Absolute Maximum Ratings 1 1. Operation of this device above any one of these parameters may cause permanent damage. Parameter Absolute Maximum Max. Input Power +20 dBm Vbias +15.75 V Operating Temperature -55°C to +85°C Storage Temperature -65°C to +125°C V 3.00
Cascadable Thin Film Amplifier, 12 dB Gain, 5 - 500 MHz AM-/AMC-151 Specifications subject to change without notice. n North America: Tel. (800) 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020 Visit www.macom.com for additional data sheets and product information. V 3.00 Electrical Specifications 2,3 TA = -55°C to +85°C Case Temperature Parameter Test Conditions Frequency Units Min. Typ. Max. Gain @ +25°C 50 MHz dB 11.5 12.0 12.5 Frequency Response — 5 - 500 MHz dB — — ±1.0 Gain Variation with Temperature — 5 - 500 MHz dB — — ±0.8 1 dB Compression Output Power 5 - 500 MHz 10 - 500 MHz dBm dBm +19 +20 Noise Figure — 5 - 500 MHz dB — — 7.0 Reverse Transmission — 5 - 500 MHz dB — -16 -13 VSWR — 5 - 500 MHz Ratio — — 2:1 Output IP2 Two-tone inputs up to +10 dBm 5 - 500 MHz dBm +48 — — Output IP3 Two-tone inputs up to +10 dBm 5 - 500 MHz dBm +34 — — Ibias Vbias = +15.0 VDC — mA — 85 100 Power Dissipation @ +15V Bias — mW — 1275 — 2. All specifications apply when operated at +15 VDC, with 50 ohms source and load impedance. 3. Heat Sinking: Operation at case temperature above 95°C is not recommended. Heat sinking adequate to dissipate 1.3W must be provided in use.
Cascadable Thin Film Amplifier, 12 dB Gain, 5 - 500 MHz AM-/AMC-151 Specifications subject to change without notice. n North America: Tel. (800) 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020 Visit www.macom.com for additional data sheets and product information. V 3.00 Typical Performance Curves Noise Figure
Ordering Information
- Mounting kit part number AU00071 required for PCB applications. Part Number Package AM-151 PIN4 TO-8-1 AMC-151 SMA Connectorized 1 dB Compression Intermodulation Intercept Gain vs. Frequency VSWR vs. Frequency 3 5 10 20 30 50 100 200 400 600 Frequency (MHz) Noise Figure (dB) +85°C +25°C 3 5 10 20 30 50 100 200 400 600 Frequency (MHz) Output Power (dBm) +85°C +25°C 3 5 10 20 30 50 100 200 400 600 Frequency (MHz) Intercept (dBm) IP2 IP3 3 5 10 20 30 50 100 200 400 600 Frequency (MHz) Gain (dB) +85°C +25°C -55°C 1.0 1.2 1.4 1.6 3 5 10 20 30 50 100 200 400 600 Frequency (MHz) VSWR RF INRF OUT