AM-146 MA-COM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Features
- 4 dB Typical Midband Noise Figure
- +38 dBm Typical Midband Third Order Intercept
- +24 dBm Typical Midband 1 dB Compression
Description
M/A-COM’s AM-146 is a coupler feedback amplifier with high intercept and compression points. The use of coupler feedback minimizes current in a high intercept amplifier. This amplifier is packaged in a flatpack with flanges. Due to the metal flatpack the thermal rise minimized. The ground plane on the PC board should be configured to remove heat from under the package. AM-146 is ideally suited for use where a high intercept, high reliability amplifier is required. FP-9 Parameter Absolute Maximum Max. Input Power +10 dBm Vbias +15.75 V Operating Temperature -55°C to +85°C Storage Temperature -65°C to +125°C Absolute Maximum Ratings 1 1. Operation of this device above any one of these parameters may cause permanent damage. C-25 Pin No. Function
1 RF OUT
2 GND
3 GND
4 GND
5 VDC
Pin No. Function
6 RF IN
7 GND
8 GND
9 GND
10 VDC
Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. High Performance Amplifier, 21 dB Gain, 10 - 500 MHz Rev. V3 AM-146/AMC-146 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Electrical Specifications: 2,3 TA = -55°C to +85°C Case Temperature Parameter Test Conditions Units Min. Typ. Max. Gain @+25oC dB 20.3 21.0 21.7 Frequency Response — dB — ±1.0 Gain Variation with Temperature — dB — — +-0.8, -1.2 1 dB Compression Output Power dBm +20.0 — Noise Figure — dB dB 7.0 5.5 Reverse Transmission — dB — -35 -30.0 VSWR — Ratio 2:1 Output IP2 Two-Tone inputs up to +10 dBm dBm +40 — — Output IP3 Two-Tone inputs up to +10 dBm dBm +30 — — Vbias — VDC +14.5 +15.0 +15.5 Ibias Vbias = +15.0 VDC mA — 130 140 Power Dissipation @ +15 V Bias mW — 2 — Frequency
50 MHz
- All specifications apply when operated at +15 VDC, with 50 ohms source and load impedance. 3. Heat Sinking: Operation at case temperature above 95°C is not recommended. Heat sinking adequate to dissipate 2 W must be provided in use. Frequency (MHz) S11 MAG/ANG S21 MAG/ANG S12 MAG/ANG S22 MAG/ANG 0.14/164.6 0.16/168.2 0.15/155.9 0.13/143.8 300 0.18/86.3 11.34/176.4 400 0.20/55.2 11.33/110.4 S-Parameter Data
Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. High Performance Amplifier, 21 dB Gain, 10 - 500 MHz Rev. V3 AM-146/AMC-146 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Typical Performance Curves