AM-143 MA-COM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Features

  • 1.9 dB Typical Midband Noise Figure
  • +7 dBm Typical Midband Output Power
  • +20 dBm Typical Third Order Intercept

Description

M/A-COM’s AM-143 is a coupler feedback amplifier with low noise figure and high intercept points for the low bias current. The use of coupler feedback minimizes noise figure and current in a high intercept amplifier. This amplifier is packaged in a TO-8 package. The ground plane on the PC board should be configured to remove heat from under the package. AM-143 are ideally suited for use where a low noise, high reliability amplifier is required. TO-8-1 Parameter Absolute Maximum Max. Input Power +20 dBm Vbias +15.75 V Operating Temperature -55°C to +85°C Storage Temperature -65°C to +125°C Absolute Maximum Ratings 1 1. Operation of this device above any one of these parameters may cause permanent damage.

Ordering Information

  1. Mounting kit part number AU00071 required for PCB applications. Outline Drawing: SMA Connectorized * ∗ Dimensions are inches (millimeters) ±0.015 (0.38) unless otherwise specified.

Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Low Noise Amplifier, 16 dB Gain, 5 - 500 MHz Rev. V4 AM-143 / AMC-143 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Electrical Specifications: 2, TA = -55°C to +85°C Case Temperature Parameter Test Conditions Units Min. Typ. Max. Gain @+25oC dB 15.3 15.8 16.3 Frequency Response — dB — ±1.0 Gain Variation with Temperature — dB — — ±0.8 1 dB Compression Output Power dBm +4 — — Noise Figure — dB — 3.5 2.7 Reverse Transmission — dB — -21 -16 VSWR — Ratio — — 2.5:1 Output IP2 Two-Tone inputs up to -10 dBm dBm +24 — — Output IP3 Two-Tone inputs up to -10 dBm dBm +16 — — Vbias — VDC +14.5 +15.0 +15.5 Ibias Vbias = +15.0 VDC mA — 13 15 Power Dissipation @ +15 V Bias mW — 200 — Frequency

50 MHz

  1. All specifications apply when operated at +15 VDC, with 50 ohms source and load impedance. Frequency (MHz) S11 MAG/ANG S21 MAG/ANG S12 MAG/ANG S22 MAG/ANG 0.32/-24.9 0.27/-24.9 0.26/-17.4 0.25/-28.0 S-Parameter Data

Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Low Noise Amplifier, 16 dB Gain, 5 - 500 MHz Rev. V4 AM-143 / AMC-143 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Typical Performance Curves