AM-123 MA-COM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Features
- 3.5 dB Typical Midband Noise Figure
- +42 dBm Typical Midband Intercept
Description
M/A-COM’s AM-123 is a coupler feedback amplifier with high intercept and compression points. The use of coupler feedback minimizes noise figure and cur- rent in a high intercept amplifier. This amplifier is packaged in a TO-8 package. Due to the internal power dissipation the thermal rise minimized. The ground plane on the PC board should be configured to remove heat from under the package AM-123 is ideally suited for use where a high intercept, high reliability amplifier is required. FP-7 Parameter Absolute Maximum Max. Input Power +23 dBm Vbias +15.75 V Operating Temperature -55°C to +85°C Storage Temperature -65°C to +125°C Absolute Maximum Ratings 1 C-32 1. Operation of this device above any one of these parameters may cause permanent damage.
Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. High Performance Amplifier, 10 dB Gain 5 - 500 MHz Rev. V3 AM-123 / AMC-123 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Electrical Specifications: 2,3 TA = -55°C to +85°C Case Temperature Parameter Test Conditions Units Min. Typ. Max. Gain @+25oC dB 9.4 10.0 10.6 Frequency Response — dB — ±0.7 Gain Variation with Temperature — dB — — ±1.0 1 dB Compression Output Power dBm dBm +16 +19 Noise Figure — dB dB 7.5 5.5 Reverse Transmission — dB — -18 -15 VSWR — Ratio Ratio 2.5:1 2:1 Output IP2 Two-Tone inputs up to +10 dBm dBm dBm +33 +40 Output IP3 Two-Tone inputs up to +10 dBm dBm dBm +22 +32 Vbias — VDC +14.5 +15.0 +15.5 Ibias Vbias = +15.0 VDC mA — 62 75 Power Dissipation @ +15 V Bias mW — 930 — Frequency
50 MHz
- All specifications apply when operated at +15 VDC, with 50 ohms source and load impedance. 3. Heat Sinking: Operation at case temperature above 95°C is not recommended. Heat sinking adequate to dissipate 1 W must be provided in use. Frequency (MHz) S11 MAG/ANG S21 MAG/ANG S12 MAG/ANG S22 MAG/ANG 0.15/92.8 S-Parameter Data
Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. High Performance Amplifier, 10 dB Gain 5 - 500 MHz Rev. V3 AM-123 / AMC-123 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Typical Performance Curves
Ordering Information
Part No. Function
1 RF OUT
2 GND
Pin No. Function