AM-119 MA-COM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Features
- 2.3 dB Typical Midband Noise Figure
- +23 dBm Typical Midband Output Power
- +40 dBm Typical Midband Third Order Intercept
Description
M/A-COM’s AM-119 is a coupler feedback amplifier with high intercept and compression points. The use of coupler feedback minimizes noise figure and current in a high intercept amplifier. This amplifier is packaged in a TO-8 package. Due to the internal power dissipation the thermal rise minimized. The ground plane on the PC board should be configured to remove heat from under the package. AM-119 is ideally suited for use where a high intercept, high reliability amplifier is required. TO-8-1 Absolute Maximum Ratings 1 1. Operation of this device above any one of these parameters may cause permanent damage.
Ordering Information
Parameter Absolute Maximum Max. Input Power +13 dBm Vbias +15.75 V Operating Temperature -55°C to +85°C Storage Temperature -65°C to +125°C Outline Drawing: SMA Connectorized * ∗ Dimensions are inches (millimeters) ±0.015 (0.38) unless otherwise specified. 4. Mounting kit part number AU00071 required for PCB applications.
Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. High Performance Amplifier, 8 dB Gain, 30 - 250 MHz Rev. V4 AM-119 / AMC-119 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Electrical Specifications: 2, 3 TA = -55°C to +85°C Case Temperature Parameter Test Conditions Units Min. Typ. Max. Gain @+25oC dB 7.5 8.0 8.5 Frequency Response — dB — ±0.75 Gain Variation with Temperature — dB — — ±1.0 1 dB Compression Output Power dBm +20 — — Noise Figure — dB — — 3.5 Reverse Transmission — dB — -11.0 -9.5 VSWR — Ratio — — 2.3:1 Output IP2 Two-Tone inputs up to +10 dBm dBm +39 — — Output IP3 Two-Tone inputs up to +10 dBm dBm +34 — — Vbias — VDC +14.5 +15.0 +15.5 Ibias Vbias = +15.0 VDC mA — 50 60 Power Dissipation @ +15 V Bias mW — 750 — Frequency
250 MHz
- All specifications apply when operated at +15 VDC, with 50 ohms source and load impedance. 3. Heat Sinking: Operation at case temperature above 95°C is not recommended. Heat sinking adequate to dissipate 1W must be provided in use.
Visit www.macomtech.com for additional data sheets and product information. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. High Performance Amplifier, 8 dB Gain, 30 - 250 MHz Rev. V4 AM-119 / AMC-119 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions is considering for development. Performance is based on target specifications, simulated results, and/or prototype measurements. Commitment to develop is not guaranteed. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. Commitment to produce in volume is not guaranteed. Typical Performance Curves