AMAX-1220_15 ADVANTECH | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 1
Technical content
Features
Motor Driver Support Pulse-type servo Number of Axes AMAX-1220: 2 AMAX-1240: 4 Interpolation Linear and circular Max. Output Speed 6.5 Mpps Step Count Range ±134, 217, 728 Pulse Output Type OUT/DIR, CW/CCW, A/B phase Position Counter ±134, 217, 728 Home Modes 13 Velocity Profiles T-Curve, S-Curve Local I/O Machine Interfaces: EL+/-, ORG and SD (Slow Down) for Each Axis Servo Driver Interfaces: ALM, RDY , SVON, INP , Break for Each Axis Position Compare I/O: LTC, CMP for Each Axis(Only available for AMAX-1240-AE) Simultaneous Move Within Multiple Modules: CSTA/CSTP (Simultaneously Start/Stop) for each model General Purpose I/O: AMAX-1220 supports 8xDI and 8xDO Encoder Interface Input Type A/B phase, CW/CCW Counts per Enc. Cycle x1, x2, x4 (AB phase only) Input Range Low: 0 ~ 0.5V High: 3.5 ~ 7V Isolation Protection 2,500 VRMS Max. Input Frequency 2 MHz @ 5 V General Bus Type AMONet RS-485 Certification CE, FCC Class A Connectors RJ-45 x 2 are for communication port DB-26 connector by transfer cable to servo drives. Other are screw terminal type connectors Dimensions (L x W x H) 141 x 108 x 60 mm (5.6" x 4.3" x 2.4") System Power 2 W @ 24 V typical Consumption Output Channel Power Consumption 120W typical, 240W max. Input Channel Power Consumption AMAX-1220: 8 W @ 24 V external power (max.) AMAX-1240: 10 W @ 24 V external power (max.) System Power Input 24 V DC within 200 mV ripple Humidity 5 ~ 95% RH, non-condensing (IEC 60068-2-3) Operating Temperature 0 ~ 60°C (32 ~ 140°F)
Ordering Information
AMAX-1220-AE Economic 2-axis AMONet Motion Control Module AMAX-1240-AE Advanced 4-axis AMONet Motion Control Module Accessories PCL-10153PA5-2E 50-pin Cable to Panasonic A4 and A5 Servo, 2 m PCL-10153PA5LS-2E 50-pin Cable to Panasonic MINAS A Servo, 2 m PCL-10153YS5-2E 50-pin Cable to Yaskawa Sigma V Servo, 2 m PCL-10153MJ3-2E 50-pin Cable to Mitsubishi J3 Servo, 2 m ●PCL-10153DA2-2E 50-pin Cable from ADAM-3955/ADAM-3956 to Delta A2 Servo, 2 m Introduction AMAX-1220 and AMAX-1240 have compact open frame designs for horizontal placement and an interface connector mounted on the board. With a transfer cable to servo drive, both models can conveniently connect to Mitsubishi J3, Yaskwa Sigma V and Panasonic A4/A5. The AMAX-1220 is an economic 2-axis AMONet slave module which supports motion functionality in point-to-point (PTP), linear & circular interpolation, simultaneously start/ stop among multiple slave modules, and brake signal to servo for emergence consideration. The AMAX-1240 is an advanced 4-axis AMONet slave module which not only supports AMAX-1220 motion functionality, but also supports advanced features in position compare and triggering function. Both linear interval and table setups are supported. End limit logic is switchable (high or low active) BoardID is switchable Easily visible LED indicators on board to do diagnosis Direct wire to servo drive to save terminal board space while installation Max. 6.5 MHz, 4-axis pulse output 28 bits counter for incremental encoder Horizontal installation for for servo or stepping motor driver Suitable for DIN-rail mounting Open Frame Type 2/ 4-axis AMONet Motion Slave Modules NEW AMAX-1220 AMAX-1240 RoHS COMPLIANT 2002/95/EC All product specifications are subject to change without notice All product specifications are subject to change without notice Last updated : 5-May-2015