AM75QB-11005S-NZ

AM75QB-NZ AIMTEC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 9

Technical content

75 Watt | DC-DC Converter

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R1 1 of 9 North America only FEATURES:

• Ultra-wide Input range up to160VDC • Input / Output Isolation up to 3000VDC
• Efficiency up to 93% • Operating Temperature: -40°C to +100°C
• Input under voltage lockout • OVP, OCP, OTP
• Continued short circuit protection • On-Off, Trim and Output Sense controls Models Single output Model Input Voltage (V) Max Input Current FL I NL (mA) Output Voltage (V) Output Current max (A) Isolation (VDC) Max Capacitive Load (uF) Efficiency (%) AM75QB-4805SH22-NZ 18-75 1756 I 80 5 15 2250 6000 91 AM75QB-4812SH22-NZ 18-75 1756 I 80 12 6.25 2250 2000 92 AM75QB-4815SH22-NZ 18-75 1756 I 80 15 5 2250 2000 93 AM75QB-4824SH22-NZ 18-75 1756 I 80 24 3.13 2250 1000 92 AM75QB-4848SH22-NZ 18-75 1756 I 80 48 1.56 2250 470 92 AM75QB-11005S-NZ 66-160 793 I 15 5 15 3000 7500 87 AM75QB-11012S-NZ 66-160 783 I 15 12 6.25 3000 6000 88 AM75QB-11015S-NZ 66-160 783 I 15 15 5 3000 4700 88 AM75QB-11024S-NZ 66-160 766 I 15 24 3.125 3000 3000 90 Add suffix “-K” for optional heat sink NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Maximum Units Voltage range 48V Vin 18-75 VDC 110V Vin 66-160 Filter π(Pi) Network Startup time 25 ms Absolute Maximum Rating 48V Vin -0.7 - 90 VDC 110V Vin -0.7 - 180 Peak Input Voltage time 1 s On/Off control ON – open or 3.5-12VDC; OFF – short to –Vin or 0-1.2VDC, Idle current 2-10mA Under voltage lockout 48V Vin 16.6 VDC 110V Vin 58 Input reflected current 48V Vin 30 mA 110V Vin 50 Isolation Specifications Parameters Conditions Rated Maximum Units Tested I/O voltage 48V models, 60 sec, 5mA 2250 VDC 110V models, 60 sec, 1mA 3000 Tested Input / Case voltage 48V models, 60 sec, 5mA 1500 VDC 110V models, 60 sec, 1mA 1500 Tested Output / Case voltage 48V models, 60 sec, 5mA 1500 VDC 10V models, 60 sec, 1mA 500 Resistance At I/O Isolation 500VDC >100 MOhm >1000 Capacitance I/O 100KHz/0.1V 2200 pF

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R1 2 of 9 North America only Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy 48V models ±1 ±3 % 110V models ±2 ±3 Line voltage regulation Vin LL to HL 48V models ±0.5 % of Vin 110V models ±0.3 Load voltage regulation 10 – 100% load 48V models ±0.75 % 110V models ±0.5 Temperature coefficient ±0.03 %/oC Ripple & Noise 20MHz Bandwidth 48V Model 12V/15V Vout 100 200 mV p-p Others 150 250 110V models 100 300 Voltage adjustment range -5 to 10 % Output voltage Sense compensation* 5 % Over voltage protection 48V models 110 - 160 % of Vout 110V models 110 - 140 Over current protection 48V models 110 190 % of Iout 110V models 130 180 Short Circuit protection Continuous Short circuit restart Auto-recovery Thermal shutdown Base plate temperature 48V models 105 ºC 110V models 115 Transient recovery time 25% load step change 48V models 200 500 µs 110V models 300 500 Transient recovery deviation 25% load step change 48V Vin, 5VDC Vout ±3 ±7.5 % Others ±3 ±5 *NOTE: If Output Sense is not used, short +Vout with +Sense and -Vout with -Sense. Keep the connection track between +Vout with +Sense and -Vout with -Sense as short as possible for stable performance. General Specifications Parameters Conditions Minimum Maximum Units Switching frequency 100% load 48V models 250 KHz 110V models 220 Base plate temperature See derating curves 48V models -40 to +85 °C 110V models -40 to +100 Storage temperature -55 to +125 °C Maximum case temperature 105 °C Thermal resistance Without heatsink – Natural convection 10.7 °C/W Without heatsink – 200LFM convection 6 Without heatsink – 400LFM convection 5 Without heatsink – 1000LFM convection 4 With heatsink – Natural convection 5.1 With heatsink – 200LFM convection 2.8 With heatsink – 400LFM convection 2.2 With heatsink – 1000LFM convection 1.8 Cooling Natural convection or forced air Humidity Non-condensing 5 95 % RH Case material 48V models Aluminum alloy case (UL94-V0) 110V models Black heat resistant plastic case (UL94-V0) Weight 48V models Without heatsink 83 g With heatsink 114 110V models Without heatsink 46 With heatsink 76 Dimensions (L x W x H) MTBF >500,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 o Maximum soldering temperature 1.5mm from case for 10 sec 300 °C

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R1 3 of 9 North America only Environment Approval Parameters Conditions Cooling EN60068-2-1, 110V models only Dry heat EN60068-2-2, 110V models only Damp heat EN60068-2-30, 110V models only Shock and Vibrations IEC/EN61373 on both 48V and 110V models Safety Specifications Pin Out Specifications Pin Single 1 +Vin

2 On/Off Control

6 Trim

DIV: 2.54 x 2.54 Dimensions: mm (inch) Case Tolerance: ±0.50 (0.02) Pin Tolerance: ± 1.50 (0.06) Pin diameter Tolerance: ±0.10 (0.004) Pin 1, 2, 3, 5, 6 & 7 diameter: 1.00 (0.04) Pin 4 & 8 diameter: 1.50 (0.06) Mounting hole screw torque: max 0.4 N m 40.20 (1.58) 61.80 (2.43) 47.20 (1.86) 26.20 (1.03) BOTTOM VIEW 12.70±1.00 (0.50±0.04) 4.50 (0.18) 50.80 (2.00) 12.48 (0.49) 7.62 (0.30) 2xM3 3.00(0.12) 6XØ1.00 (0.04) Side view 2 x ᴓ 3.50(0.14) 2xᴓ 1.50(0.06) 2 x ᴓ 2.00(0.08) 6 x ᴓ 1.50(0.06) Parameters Standards CISPR32/EN 55032, Class B, with external filter IEC 61000-4-2 48V Meet EN50121-3-2, Contact ±6KV, Air ±8KV, Criteria B 110V Contact ±6KV, Air ±8KV, Criteria B IEC 61000-4-3 48V Meet EN50121-3-2, 10V/m, Criteria A 110V 10V/m, Criteria A IEC 61000-4-4 48V Meet EN50121-3-2, ±2KV with external filter, Criteria B 110V For 110V models, ±2KV with external filter, Criteria B EN50121-3-2 48V differential mode ±1KV, 1.2/50us, source impedance 42Ω with external filter, Criteria B IEC 61000-4-5 110V Meet EN50155, L- L ±2KV, L-G ±4KV with external filter, Criteria B IEC 61000-4-6 48V Meet EN50121-3-2, 10Vrms, Criteria A 110V 10Vrms, Criteria A EN50155 110V 100%0%, 10ms, with external filter, Criteria B

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R1 4 of 9 North America only 48V Models With Optional Heatsink DIV: 2.54 x 2.54 Dimensions: mm (inch) Case Tolerance: ±0.50 (0.02) Pin Tolerance: ± 1.50 (0.06) Pin diameter Tolerance: ±0.10 (0.004) Pin 1, 2, 3, 5, 6 & 7 diameter: 1.00 (0.04) Pin 4 & 8 diameter: 1.50 (0.06) Mounting hole screw torque: max 0.4 N m 40.20 (1.58) 61.80 (2.43) 47.20 (1.86) 26.20 (1.03) BOTTOM VIEW 27.70±1.00 (1.09±0.04) 4.50 (0.18) 50.80 (2.00) 7.62 (0.30) 2xM3 3.00(0.12) 6XØ1.00 (0.04) Side view 2xᴓ 1.50(0.06) 2 x ᴓ 3.50(0.14) 2 x ᴓ 2.00(0.08) 6 x ᴓ 1.50(0.06) 12.48 (0.49) 110V Model Dimensions DIV: 2.54 x 2.54 Dimensions: mm (inch) Case Tolerance: ±0.50 (0.02) Pin Tolerance: ± 1.50 (0.06) Pin diameter Tolerance: ±0.10 (0.004) Pin 1, 2, 3, 5, 6 & 7 diameter: 1.00 (0.04) Pin 4 & 8 diameter: 1.50 (0.06) Mounting hole screw torque: max 0.4 N m 39.20 (1.54) 60.80 (2.39) 47.20 (1.86) 26.20 (1.03) BOTTOM VIEW 12.70±1.00 (0.50±0.04) 4.20 (0.17) 50.80 (2.00) 31.58 (1.24) 7.62 (0.30) 2xM3 3.00(0.12) 6XØ1.00 (0.04) Side view Aluminum baseplate 2 x ᴓ 3.50(0.14) 2xᴓ 3.50(0.14) 2 x ᴓ 2.00(0.08) 6 x ᴓ 1.50(0.06)

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R1 5 of 9 North America only 110V Models With optional heatsink DIV: 2.54 x 2.54 Dimensions: mm (inch) Case Tolerance: ±0.50 (0.02) Pin Tolerance: ± 1.50 (0.06) Pin diameter Tolerance: ±0.10 (0.004) Pin 1, 2, 3, 5, 6 & 7 diameter: 1.00 (0.04) Pin 4 & 8 diameter: 1.50 (0.06) Mounting hole screw torque: max 0.4 N m 39.20 (1.54) 62.00 (2.44) 47.20 (1.86) 26.20 (1.03) BOTTOM VIEW 30.80±1.00 (1.21±0.04) 4.20 (0.17) 50.80 (2.00) 31.58 (1.24) 7.62 (0.30) 2xM3 3.00(0.12) 6XØ1.00 (0.04) Side view 2 x ᴓ 3.50(0.14) 2xᴓ 3.50(0.14) 2 x ᴓ 2.00(0.08) 6 x ᴓ 1.50(0.06) Derating -40 0 40 60 80 100 100 Safe Operating Area Output Power (%) Ambient Temperature º C AM75QB-4805S-NZ Without heatsink -20 Vin = 24 Vin = 48 -40 0 40 60 80 100 100 Safe Operating Area Output Power (%) Ambient Temperature º C AM75QB-4805S-NZ With heatsink -20 Vin = 24 Vin = 48 -40 0 40 60 80 100 100 Safe Operating Area Output Power (%) Ambient Temperature º C AM75QB-4812/15/24/48S-NZ Without heatsink -20 Vin = 24 Vin = 48 -40 0 40 60 80 100 100 Safe Operating Area Output Power (%) Ambient Temperature º C AM75QB-4812/15/24/48S-NZ With heatsink -20 Vin = 24 Vin = 48

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R1 6 of 9 North America only - 40 10 20 40 60 80 100 100 Safe Operating Area Output Power (%) Ambient Temperature º C 30 50 70 90 AM75QB-11005S-NZ Without heatsink With 200 LFM Natural convection With 400 LFM With 1000 LFM 100 Safe Operating Area Output Power (%) Ambient Temperature º C - - 40 10 20 40 60 80 10030 50 700 90 With 200 LFM Natural convection With 400 LFM With 1000 LFM AM75QB-11005S-NZ With heatsink 100 Safe Operating Area Output Power (%) Ambient Temperature º C - 40 10 20 40 60 80 10030 50 700 90 With 200 LFM Natural convection With 400 LFM With 1000 LFM AM75QB-11012S-NZ Without heatsink 100 Safe Operating Area Output Power (%) Ambient Temperature º C - 40 10 20 40 60 80 10030 50 700 90 With 200 LFM Natural convection With 400 LFM With 1000 LFM AM75QB-11012S-NZ With heatsink 100 Safe Operating Area Output Power (%) Ambient Temperature º C - 40 10 20 40 60 80 10030 50 700 90 AM75QB-11015S-NZ Without heatsink With 200 LFM Natural convection With 400 LFM With 1000 LFM 100 Safe Operating Area Output Power (%) Ambient Temperature º C - 40 10 20 40 60 80 10030 50 700 90 AM75QB-11015S-NZ With heatsink With 200 LFM Natural convection With 400 LFM With 1000 LFM

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R1 7 of 9 North America only Typical application circuit 48V models DC DC + Vin - Vin Cin 220 µF Cout +Vout - Vout Single Output + + FUSE Output 5V 12V/15V 24V 48V Cout 470 µF 220 µF 100 µF 100 µF 110V Models DC DC + Vin - Vin Cin 100 µF Cout 220 µF +Vout - Vout Single Output + + Recommended External EMC filter 48V models DC DC +Vout - Vout CY1 1nF/400VAC + Vin - Vin + Vout 47µF - Vout CY2 1nF/400VAC CY4 1nF/400VAC 2.2µF LDM 1.5µH + Vin - Vin LCM1 1mH 2.2µF 2.2µF 2.2µF 2.2µF 2.2µF 2.2µF CY3 1nF/400VAC 100 Safe Operating Area Output Power (%) Ambient Temperature º C - 40 10 20 40 60 80 10030 50 700 90 AM75QB-11024S-NZ Without heatsink With 200 LFM Natural convection With 400 LFM With 1000 LFM 100 Safe Operating Area Output Power (%) Ambient Temperature º C - 40 10 20 40 60 80 10030 50 700 90 AM75QB-11024S-NZ With heatsink With 200 LFM Natural convection With 400 LFM With 1000 LFM

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R1 8 of 9 North America only 110V Models C1, C2, C3, C4 & C5 C6, C7, C8 & C9 (EC type) LCM1 LCM2 D1 2.2 µF / 250V 100 µF / 400V 2200 µH *2 4700 µH *2 SF306 Trimming Output voltage can be externally trimmed by utilizing the methods as shown below Fixed Resistor Variable Potentiometer Leave open if not used. AM75QB-xxx05S-NZ xxx can be 48 or 110 Trim down % 1 2 3 4 5 Trim up % 1 2 3 4 5 6 7 8 9 10 DC DC +Vout - Vout MOV S20K130 CY1 2.2nF/400VAC + Vin - Vin + Vout - Vout CY2 2.2nF/400VAC CY3 2.2nF/400VAC CY4 2.2nF/400VAC LCM2 C5C4 LCM1 C2C1 C3C7C6 C8 LDM 10µH +++ + Vin - Vin

www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R1 9 of 9 North America only AM75QB-xxx12S-NZ xxx can be 48 or 110 Trim down % 1 2 3 4 5 Trim up % 1 2 3 4 5 6 7 8 9 10 AM75QB-xxx15S-NZ xxx can be 48 or 110 Trim down % 1 2 3 4 5 Trim up % 1 2 3 4 5 6 7 8 9 10 AM75QB-xxx24S-NZ xxx can be 48 or 110 Trim down % 1 2 3 4 5 Trim up % 1 2 3 4 5 6 7 8 9 10 AM75QB-4848S-NZ Trim down % 1 2 3 4 5 Trim up % 1 2 3 4 5 6 7 8 9 10 NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5.Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate